So, I just tried this. Got into Relearning active, went and let some air out of the front driver tire and it never beeped. Got to just about completely flat and no beep. Does this mean this sensor is bad? 2013 GMC Sierra 1500 WT 4X4 with no DIC buttons, only odometer that scrolls through.
Thank you … from your videos I have done my first brake job, front struts , rear shocks , now I’m in to the body….. again thank you for making it easy and boosting my confidence
Thanks for the visual; between your guidance and the manual, resolved the issue! There was two messages on the display - service tire pressure monitor system and check tire pressure (on a few of the tires). We did have to try it a few times; once by decreasing the air pressure but it didn't clear the message but then followed the steps again and increased the air pressure (for those that don't have the manual, increasing/decreasing air pressure is listed in it) and it worked!
Mine will beep twice when I click relearn but then I get nothing on any of the tires when I try to release some air?? Any suggestions? Thanks in advance!
Hey just gotbdonebtrying this and it still wont go away....but my truck did 2 beeps on the third wheel and would let me get to driver rear any suggestions plleeeaase
That's because the order in which he deflate tire was wrong on my 2008 chevy silverado you gotta start left driver side and then rear left until the last one right passenger tire.
everything worked as described until I started letting air out of front left tire. it never beeped after approx. 30 seconds of letting air out. started over and the same thing happened again.
@@ComedyBros5 same thing happened to me but the sensor reads fine on the dash it’s another sensor but yet the front left tire would never beep when I’m letting air out of it and it’s in relearn mode
So my only concern or question is do (they) compensate for the materials that the new tires are made of. Every year is a better tire with a better price.
I can get the 2 beeps, and the marker light on the left fron comes on, but I can let all of air out of the tire and I will not get another beep to move to the next tire.
If you do this and on the last tire it says the same thing "service tire monitering system" does that mean i need a new tire pressure reader. Mine is on the passenger front. It says "learning" until i get to that tire.
I have my dash reading "Tire learning active", and i get the 2 horn chirps. But when i start letting air out of the first tire, i never get a horn beep. Went all the way to 2 psi. These are new used tires i purchased, and were already on the rims. Any ideas?
What did y'all figure out on this? I just put bigger tires on my yukon and they can inflate up to 65psi. I know in the past when my pressure was over 45 in my stock wheels it gave me the warning light and eventually blew a fuse. Is there a fix to allow a high pressure without the system going crazy?
You should always put the PSI that it shows on the tag or sticker that’s on the inside door jam on the drivers side.. provided they’re a stock size tire ..
Good question but who does actually knows the answer so far I can't find any answer between all this comment...I sure need help to finish my clients vehicle in the next 2 weeks not to mention my pitbull decided to chew my sensor scan tool
Everything went well util I got to the last tire (Driver's side rear). It never beeped even though I bled it down to 20 PSI. Does this mean the censor is bad? How hard is it to replace one?
I see this is almost a year late, but yes, it means you need a new one. You simply buy a replacement online (Amazon has 'em for $15). Take it a tire shop, and they swap it out. Then, simply do the process shown in this video.
I don't have the dic buttons, and when scrolling it doesn't have the re learn tpms at on the display, so how would I do this? I do have a key fob. I have 2008 4x4 lt chevy silverado thank you for all your advice.
All mine quit working at once on my 2010 while going down the highway. Put it in relearn. Bled them all the way down to 10 psi with no horn beep at all. Service tire monitor light comes on before I even crank over the ignition. Did all my sensors die at once or am I stupid?
Yes. You should hear 2 beeps once you get to the driver's side rear tire. Once you hear that, it's out of the relearn sequence & you can air them up in whatever order you want.
So my clients 2011 Silverado WT comes with key fob but once I get to the relearning tire positions and release 30 second worth of air per tire the horn won't beep not sure what else to do other than probably order new sensors. I could really use some help since my dog decided to chew my sensor scan tool...if anyone with knowledge/experience is watching this comment I would I appreciate it ur help. Thanks and blessings. Happy holidays y'all
i have done this , and the drivers side front didnt beep , went over to the r/front and it beeped, then to the r/rear it beeped over to the L/rear it didnt beep .. but? when the truck sits it goes off , it only comes on after i drive it more than 20 miles or so my truck is 2011 LS reg/cab .. with 48,+++ miles on it
I got to try this because sometimes my break lights won’t even come on while pressing the brake so I can’t change gears they told me because of the tms light being on it’s messing with my break lights is this true?
i tired this on my truck but the truck wont learn the front driver tire. i tried multiple times and tired to increase pressures but no luck. what could be the problem?
Have a 2011 siverado 1500 ,no key fob, same dash displays as this truck in video, dont have the button to push on the dash to get to the relearn display?
Soooo everyone else on RUclips is doing the order the other way from what you say. They're going driver front first then passenger back then around..you did fronts first. I'm really confused
Hi Thank you for the help. This what I was looking for. I followed all the steps ( Silverado 1500 WT) till pressing the button where you hear the horn , but Mine did not sound any horn and it didn't show “ Re-learn tire position ACTIVE” , it only flashed winked once and nothing else. Is there something wrong. I appreciate all inputs
+Sardook Thank you for the great reply. We love to empower our customers by showing you how-to perform your own auto repairs while installing our high quality auto parts. Have a great day! 1aauto.com
+Omar Alrubaiee We don't have a how-to video for your vehicle right now, but the basic steps in this video should be enough to do this task. Buy this part for your vehicle on 1AAuto.com: 1aau.to/m/Shop-1AAuto-c
thanks for the informative video. Why do they even have a TPS when it only takes a minute to check tire pressures once a week or so. another example of tech overkill:)
You're wrong. Yes, you can also do this relearn process with a tool, and it makes the process easier, but you don't need to "reset the system" with a tool. This will work whether you replace a tpms sensor with a new one, rotate tires, change from a summer set of wheels to winter wheels, etc. The only thing necessary is that you have the correct 315 MHz sensors installed. Stop spewing misinformation.
+__Stop it__ We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
@@__stopit__5259 My 09 suburban illuminates the turn signal of the wheel it wants you to work on (starts with front left). When it is programmed the light goes out and the next one lights up. Maybe yours does too?
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto
√ *Do it Yourself*
√ *Save Money*
So, I just tried this. Got into Relearning active, went and let some air out of the front driver tire and it never beeped. Got to just about completely flat and no beep. Does this mean this sensor is bad? 2013 GMC Sierra 1500 WT 4X4 with no DIC buttons, only odometer that scrolls through.
Thank you … from your videos I have done my first brake job, front struts , rear shocks , now I’m in to the body….. again thank you for making it easy and boosting my confidence
I want to thank you for everything you guys do for the General Public
+Rosendo Madriz Thanks for checking us out! We are happy to hear these help! 1aau.to/m/Shop-1AAuto-c
Thanks for the visual; between your guidance and the manual, resolved the issue! There was two messages on the display - service tire pressure monitor system and check tire pressure (on a few of the tires). We did have to try it a few times; once by decreasing the air pressure but it didn't clear the message but then followed the steps again and increased the air pressure (for those that don't have the manual, increasing/decreasing air pressure is listed in it) and it worked!
How much you decrease your tire pressure? I start at 36 psi and I hear no horn beeping. Tire is down to 20 psi.
U JUST SAVED ME 160 DOLLARS THANKS ALOT.
Mine will beep twice when I click relearn but then I get nothing on any of the tires when I try to release some air?? Any suggestions? Thanks in advance!
what if I put newer tire rims on still Chevy but my 2007 not see the 2017 rims setup?? is there a work around for this??
Hey just gotbdonebtrying this and it still wont go away....but my truck did 2 beeps on the third wheel and would let me get to driver rear any suggestions plleeeaase
That's because the order in which he deflate tire was wrong on my 2008 chevy silverado you gotta start left driver side and then rear left until the last one right passenger tire.
everything worked as described until I started letting air out of front left tire. it never beeped after approx. 30 seconds of letting air out. started over and the same thing happened again.
Adam Gillen sweet no one replied! That’s awesome because that just happened to me today
Same thing happened to me , any suggestions ?
@@nickwelch2002 It means you need a new sensor for the one that doesn't beep.
@@ComedyBros5 same thing happened to me but the sensor reads fine on the dash it’s another sensor but yet the front left tire would never beep when I’m letting air out of it and it’s in relearn mode
So my only concern or question is do (they) compensate for the materials that the new tires are made of. Every year is a better tire with a better price.
Is this only for stock tires because my 07 Silverado has 07 SUV tires and IT not work ! What do i wrong
Thanks for this video. I just bought new rims and tires and new tpms sensors for my truck and imma put them on tomorrow
Best DIY automotive channel around
What if you relieve the tire pressure on the front passenger side tire and it won't beep, even after a minute?
Mine doing the same but only on rt front wont beep..
@@jeffdonovan3504 Same here. 2007 Silverado 2500. Only RF won't beep. Now it stays in Check Tire Press Mon. system light on.
I can get the 2 beeps, and the marker light on the left fron comes on, but I can let all of air out of the tire and I will not get another beep to move to the next tire.
If you do this and on the last tire it says the same thing "service tire monitering system" does that mean i need a new tire pressure reader. Mine is on the passenger front. It says "learning" until i get to that tire.
Love it straight to the point and worked like a charm
Thank you for this video, how do we take it out of "tire calibrate mode"?
I have my dash reading "Tire learning active", and i get the 2 horn chirps. But when i start letting air out of the first tire, i never get a horn beep. Went all the way to 2 psi. These are new used tires i purchased, and were already on the rims. Any ideas?
Sounds like you don’t have tpms sensors in those rims. The truck doesn’t have anything to communicate with.
No sensor
What if the new tire requires a higher psi... does it automatically adjust to what you inflate the tire to?
I'll be doing my truck this weekend. I'll let you know for sure if it does.
What did y'all figure out on this? I just put bigger tires on my yukon and they can inflate up to 65psi. I know in the past when my pressure was over 45 in my stock wheels it gave me the warning light and eventually blew a fuse. Is there a fix to allow a high pressure without the system going crazy?
You should always put the PSI that it shows on the tag or sticker that’s on the inside door jam on the drivers side.. provided they’re a stock size tire ..
Good question but who does actually knows the answer so far I can't find any answer between all this comment...I sure need help to finish my clients vehicle in the next 2 weeks not to mention my pitbull decided to chew my sensor scan tool
Everything went well util I got to the last tire (Driver's side rear). It never beeped even though I bled it down to 20 PSI. Does this mean the censor is bad? How hard is it to replace one?
I see this is almost a year late, but yes, it means you need a new one. You simply buy a replacement online (Amazon has 'em for $15). Take it a tire shop, and they swap it out. Then, simply do the process shown in this video.
You can skip that tire and let the air out of a different tire to trick the system to get your light to go out
I don't have the dic buttons, and when scrolling it doesn't have the re learn tpms at on the display, so how would I do this? I do have a key fob. I have 2008 4x4 lt chevy silverado thank you for all your advice.
All mine quit working at once on my 2010 while going down the highway. Put it in relearn. Bled them all the way down to 10 psi with no horn beep at all. Service tire monitor light comes on before I even crank over the ignition. Did all my sensors die at once or am I stupid?
Thank you very much for your Professionalism and love to people. Gid bless yall!!
What if your truck doesn’t have the “ Re-learn tire position” option ? Is there another way ?
Did you ever find out bro ? Mine doesn’t say that either.
Did you end up figuring it out?
After doing some research if you press the remote key lock and unlock button at the same time while your key is turned on but engine off it may work.
Also does not have or have remove
Its the unlock buttons
so once the last tire beeps the horn then you can re inflate any tire no particular order?
Yes. You should hear 2 beeps once you get to the driver's side rear tire. Once you hear that, it's out of the relearn sequence & you can air them up in whatever order you want.
So my clients 2011 Silverado WT comes with key fob but once I get to the relearning tire positions and release 30 second worth of air per tire the horn won't beep not sure what else to do other than probably order new sensors. I could really use some help since my dog decided to chew my sensor scan tool...if anyone with knowledge/experience is watching this comment I would I appreciate it ur help. Thanks and blessings. Happy holidays y'all
i have done this , and the drivers side front didnt beep , went over to the r/front and it beeped, then to the r/rear it beeped over to the L/rear it didnt beep .. but? when the truck sits it goes off , it only comes on after i drive it more than 20 miles or so my truck is 2011 LS reg/cab .. with 48,+++ miles on it
what if i dont have a odo button to hold down? no fob & no buton...??
Same here , what to do?
This works on a 2010 2500 with a key fob ? Or is the menu option inside only available when the service tpms error shows ?
I have a 2013 Silverado 1500 and it never shows the option relearn tire positions
If one wheel isnt beeping it needs a sensor but why doesn't it say the psi in any of the wheels on the dash display
The tire monitor systems on these year trucks were not that advanced yet to do that.
I put new sensor on one of my tire and don’t work, don’t beep like the other tires I don’t know what is wrong.
I got to try this because sometimes my break lights won’t even come on while pressing the brake so I can’t change gears they told me because of the tms light being on it’s messing with my break lights is this true?
My relearn tire position indicator doesn't show to select?
Horn doesnt beep on front driver side but does on the other three ????
Didn't get the two chirps system didn't enter tire relearn active mode..?
i tired this on my truck but the truck wont learn the front driver tire. i tried multiple times and tired to increase pressures but no luck. what could be the problem?
the best place for repair info.. and great prices on parts also
I tried on a 2013 suburban and it didn’t work. There’s no option for that.
My 2008 Silverado has key fob for alarm only, doesn't show relearn tire pressure
Have a 2011 siverado 1500 ,no key fob, same dash displays as this truck in video, dont have the button to push on the dash to get to the relearn display?
Me neither did u figure it out
This order doesn't work on a 2008 chevy silverado
What if you don't have a key fob, and that option doesn't show up
Soooo everyone else on RUclips is doing the order the other way from what you say. They're going driver front first then passenger back then around..you did fronts first. I'm really confused
I don't have "tire relearning" read, help?
Thanks for this video very helpful
Thanks
If one of the sensors is faulty will the relearn procedure still work?
No
So if my Silverado says service tps system is that what this means
Bad sensor
Hi
Thank you for the help. This what I was looking for. I followed all the steps ( Silverado 1500 WT) till pressing the button where you hear the horn , but Mine did not sound any horn and it didn't show “ Re-learn tire position ACTIVE” , it only flashed winked once and nothing else. Is there something wrong.
I appreciate all inputs
+Sardook Thank you for the great reply. We love to empower our customers by showing you how-to perform your own auto repairs while installing our high quality auto parts. Have a great day! 1aauto.com
Once you get to "relearn tire position" selection you must let go and then long press or hold the stick in until the horn beeps.
Does this works for chevy traverse 2017?
+Omar Alrubaiee We don't have a how-to video for your vehicle right now, but the basic steps in this video should be enough to do this task. Buy this part for your vehicle on 1AAuto.com: 1aau.to/m/Shop-1AAuto-c
Not the same on 2010 HD2500. Nothing to press there. Not the drone I was looking for.
+Tv S Thanks for checking us out! 1AAuto.com
Thank you so much!!!
+Isela Martinez Gomez Thanks for checking us out! 1AAuto.com
Sweet!
This does not work on LTZ package
thanks for the informative video. Why do they even have a TPS when it only takes a minute to check tire pressures once a week or so. another example of tech overkill:)
As in the owners manual...
Doesn't work on a 2013.
Each sensor has a unique code so when you rotate tires you have to reset the system with a tool. Says so on the driver manual. This method won't work
You're wrong. Yes, you can also do this relearn process with a tool, and it makes the process easier, but you don't need to "reset the system" with a tool. This will work whether you replace a tpms sensor with a new one, rotate tires, change from a summer set of wheels to winter wheels, etc. The only thing necessary is that you have the correct 315 MHz sensors installed. Stop spewing misinformation.
Doesn’t work the same for 2010
2011 does not have relearn on dash
If you have a fob, turn the key on amd hold lock and unlock on the fob until it pops up
My 2012 neither.
not one one of them beeped ant suggestions
probly have the wrong sensors inside the wheel
So....... my horn don’t work lol
+__Stop it__ We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
How can u do the tpms reset without a horn?
@@__stopit__5259 My 09 suburban illuminates the turn signal of the wheel it wants you to work on (starts with front left). When it is programmed the light goes out and the next one lights up. Maybe yours does too?
Why if one tire do not make the noise with the horn please help me
lugardo garcia did you ever find the solution I have the same problem
Isaul Martinez no creo que es el censor malo
It means the tire pressure sensor needs to be replaced in that specific tire that didn't beep.
nicholas jamele yes it what I think thankyou
@@njamele but it still reads tire pressure
Last tire never beeps this is the 3rd new set of tpms it has to be the brain inside that messed up chey
What a ignorant system. Geez
When I scroll through the options it does not have an option to relearn anything except the key fob. 2010silverado