I followed this had same fault of a dry joint so the car wouldn’t come out of park. Very easy to do took longer stripping console out than the repair. Thankyou saved me a few hundred quid.
How can i get mine fixed i took it to a detail shop after they got done with it now the shifter is stuck up and i cannot rotate in to gear and it has faults on the dash
Thanks for the share of knowledge, I have a little request, have you a detailed photos of the PCB, I have a PCB without some components, precisely under the start stop button, on the component side. Very thanks Gerry
I used a few rubber bands to hold that black pin piece and wrapped around it and clamped it down to hold it back so that way it wouldn’t get in the way of the shifter. Save me lots of money.
I this considered the “Transmission Control Unit”. Dealer says TCM module fault codes cause of the unable to apply parking brake. Also did you have to have the new one reprogrammed for the car? 2015 xf.
Thanks for this video. I am having this very same problem, this is, gear selector coming up but stuck in park. I will definitely give your suggestions a try this weekend!
No luck for me. I removed the small piece that blocks the selector, as I did not see any dry joint, and now the car shows messages for gearbox failure and faulty parking brake. I checked for messages with the OBDII and it reported a failure U101B, apparently a failure when connecting to the selector module.
@@santiagodavila1426 Brought it to the shop, resulting in a 800€ bill. I only did so because I thought the unit needed programming, but it didn’t. Had I knew, I would have just bought the unit second hand for 150€ and plugged it in.
@@markosanz do you know the cause of the mis function.? My car was just fine, until I decided to clean it really good a good n nice looking detail, i sprayed water and soap all over, in assuming that’s my issue 😭
@@santiagodavila1426 same happend to me i took it to get detail car went in running now it wont go in to gear it starts but it has a gear box failure and park brake fault and the shifter is stuck in the up position and no light come up infication what gear its in did you get yours fixed
Im just in the process of building my unit back up after replacing the plastic thread bracket piece that had snapped in the bottom of the unit (stopped it rising, but still allowed me to select gears all be it with a bit of force). I have now replaced this and built it back up but when connecting it back to the car it seems to be intermittent on wanting to rise? Not sure if i have positioned everything correctly? Can anyone be of any help? Many thanks, Ross
😊Hi Kevin wonder if you can help me. I have a 2009 Jag XF 3.0 diesel. Yesterday the gear selector got stuck in drive and it just won't budge. Had to leave the car where it was. Can you make any suggestions for rectification. Many thanks Tim
Please help. 2009 Jaguar XF, I was doing a interior detail on my car. I did use spray to clean my dash, degreaser, so after I finished, I tried to move my car and my shifter got stuck in P, after messing around with it now is stuck in D.. please help me.!
Hello I can’t get my car out of park but everything is working like it should but is there a shift lock solenoid that can break?? Or why I can’t get it out of park
Hi Steve Great video Mine is stuck in park, changed break pedal switch, still stuck Any idea where I can get a second hand one and is it plug in and play or do u have to get the software on it Cheers Steve
Hi Kevin thanks for the video, very helpful. Can you please clarify, I have a jaguar XF 2009 and the unit looks the same, If I need to replace it with a 2nd hand unit from another same model car, will I need to code it before using it? Or will it work without coding?...much appreciated
Same here bro this happened to me earlier and it was able to work after messing with the knob. I was told to be careful and not getting it wet in there. And then I had to clear the codes by disconnecting the battery. So far nothing yet. Do you have any recommendations or advice?
I had rain get in to my Jag XF 2015 and now the gear knob won't switch into gears. I get a "gearbox fault" message. I think looking at this video the computer/circuit board got fried, faulty resister or solenoid or both. I bought a whole Transmission selector that fit the 2015 XF.....Mechanic is still saying the knob will not turn and thinks he needs to reprogram....Any thoughts?
I have a 2009 XF, every works fine, until yesterday, I was doing a detail on my car, I did sprayed water and soap to all over my dash and my console, and after that my shifter is stuck in P and it’s showing the TRANSMISSION FAULT 😭
@@santiagodavila1426 my car did this earlier and now it’s working after letting it dry and disconnecting the battery to take the clothes off the dash. Do you have any advice or recommendations? Or what are your thoughts?
Anyone wanting to actually repair their control, please skip to the 7 minute mark. Thats where the real repair starts! Great video!
you only welded that resistor and the shifter was fine ??
Excellent video, I have same problem, thank you for being so thorough, I’m now subscribed
I followed this had same fault of a dry joint so the car wouldn’t come out of park. Very easy to do took longer stripping console out than the repair.
Thankyou saved me a few hundred quid.
Did you half to code it
No as it was original unit I only re soldered the one resistor. Cars still fine to this day.
Nice hopefully my repair is that simple would yk if a new pr used one would half to be reprogrammed?
Great find! I just finished a board repair where the customer spilled two mixed drink that worked it's way to the circuit board.
Did you fix it in your own.?
How can i get mine fixed i took it to a detail shop after they got done with it now the shifter is stuck up and i cannot rotate in to gear and it has faults on the dash
An amazing video. Thank You.
Thanks for the share of knowledge, I have a little request, have you a detailed photos of the PCB, I have a PCB without some components, precisely under the start stop button, on the component side. Very thanks
Gerry
thtanks for sharing with us your experience
Thanks mate for this video.
Hope it helps you out if you ever have the same problem.
I used a few rubber bands to hold that black pin piece and wrapped around it and clamped it down to hold it back so that way it wouldn’t get in the way of the shifter. Save me lots of money.
Thanks for the nice video hats off
This is a great informative video.Thank you so much. However, it's such a shame the shaking was so bad. Maybe purchase a try-pod or stand.
This video is a life saver, It worked for me .
you only welded that resistor and the shifter was fine ??
@@mzojuqa2110 yes I rewelded old one and shift lock started working as intended
I this considered the “Transmission Control Unit”. Dealer says TCM module fault codes cause of the unable to apply parking brake. Also did you have to have the new one reprogrammed for the car? 2015 xf.
nice video i also broke mine down and the pins were my problem they broke
Does this also work on the newer Land Rovers with that shifter.
Thanks for this video. I am having this very same problem, this is, gear selector coming up but stuck in park. I will definitely give your suggestions a try this weekend!
No luck for me. I removed the small piece that blocks the selector, as I did not see any dry joint, and now the car shows messages for gearbox failure and faulty parking brake. I checked for messages with the OBDII and it reported a failure U101B, apparently a failure when connecting to the selector module.
@@markosanz how did you fix it
@@santiagodavila1426 Brought it to the shop, resulting in a 800€ bill. I only did so because I thought the unit needed programming, but it didn’t. Had I knew, I would have just bought the unit second hand for 150€ and plugged it in.
@@markosanz do you know the cause of the mis function.?
My car was just fine, until I decided to clean it really good a good n nice looking detail, i sprayed water and soap all over, in assuming that’s my issue 😭
@@santiagodavila1426 same happend to me i took it to get detail car went in running now it wont go in to gear it starts but it has a gear box failure and park brake fault and the shifter is stuck in the up position and no light come up infication what gear its in did you get yours fixed
Iv a mk1 XF 2011. Can I use a mk2 module? Also if I have a 3.0 diesel will the 2.2 module work?
Im just in the process of building my unit back up after replacing the plastic thread bracket piece that had snapped in the bottom of the unit (stopped it rising, but still allowed me to select gears all be it with a bit of force). I have now replaced this and built it back up but when connecting it back to the car it seems to be intermittent on wanting to rise? Not sure if i have positioned everything correctly? Can anyone be of any help? Many thanks, Ross
😊Hi Kevin wonder if you can help me. I have a 2009 Jag XF 3.0 diesel. Yesterday the gear selector got stuck in drive and it just won't budge. Had to leave the car where it was. Can you make any suggestions for rectification. Many thanks Tim
What if the key board get wet would it stop it from working or turning shift?
Please help.
2009 Jaguar XF, I was doing a interior detail on my car. I did use spray to clean my dash, degreaser, so after I finished, I tried to move my car and my shifter got stuck in P, after messing around with it now is stuck in D.. please help me.!
Hello I can’t get my car out of park but everything is working like it should but is there a shift lock solenoid that can break?? Or why I can’t get it out of park
Do you need to reprogram after replacement?
Hi Steve
Great video
Mine is stuck in park, changed break pedal switch, still stuck
Any idea where I can get a second hand one and is it plug in and play or do u have to get the software on it
Cheers Steve
Hi Kevin thanks for the video, very helpful. Can you please clarify, I have a jaguar XF 2009 and the unit looks the same, If I need to replace it with a 2nd hand unit from another same model car, will I need to code it before using it? Or will it work without coding?...much appreciated
Did he ever get back to anyone ? I have problems with my xf I need advice
mine shifter is loose and wont shoot up, looks like some gear are broken in the shifter. How do i fix that?
Hey . Great video . Have a 2010 jaguar xf premium stuck in reverse. Any advice on how I can fix the issue . Thanks 👍 for your help
Same here bro this happened to me earlier and it was able to work after messing with the knob. I was told to be careful and not getting it wet in there. And then I had to clear the codes by disconnecting the battery. So far nothing yet. Do you have any recommendations or advice?
How much are these used ? And would it need to be programmed 9
What to do if stuck in drive
Mines stuck in reverse currently now I know what’s wrong with it
Sounds like you're from Stoke?😆
That's one part they should have left manual
As well as ignition
I had rain get in to my Jag XF 2015 and now the gear knob won't switch into gears. I get a "gearbox fault" message. I think looking at this video the computer/circuit board got fried, faulty resister or solenoid or both. I bought a whole Transmission selector that fit the 2015 XF.....Mechanic is still saying the knob will not turn and thinks he needs to reprogram....Any thoughts?
I have a 2009 XF, every works fine, until yesterday, I was doing a detail on my car, I did sprayed water and soap to all over my dash and my console, and after that my shifter is stuck in P and it’s showing the TRANSMISSION FAULT 😭
@@santiagodavila1426 how did u fix I have same problem. Did it work after it dried ?
@@santiagodavila1426 my car did this earlier and now it’s working after letting it dry and disconnecting the battery to take the clothes off the dash. Do you have any advice or recommendations? Or what are your thoughts?
What a ridiculously complex way of performing a simple task. Just use a cable or rod, it'll work reliably for 50 years.
I wish this video could be narrated in English I think this is called pig Latin? Bits and pieces of English mixed in garble. Video was Helpful