HTML-код
- Опубликовано: 17 сен 2016
- Today, We are Replacing The Tub Seal and Bearing Kit on a Maytag Bravos Made by Whirlpool. Part Number W10435302, Model Number MVWB700VQ0. This repair can also be done for Most Whirlpool Cabrio and Kenmore Oasis Models.
Please Like this Video, Share and Subscribe for Future DIY Videos. Support Our Channel by Using the Affiliate Links Below. (By Using them, We do Earn a Small Commission at NO Extra Expense to You) If You Can, You may Also Leave a Tip Below. Thanks For Watching and for the Support.
Maytag Bravos Washer F51 Error Code: • How to Fix F51 Error C...
Washer Bearing Kit (OEM)
- Amazon: amzn.to/3vN1fuZ
- RepairClinic: bit.ly/3uaJhlJ
- eBay: ebay.us/UOYjVG
Washer Bearing Tool:
- Amazon: amzn.to/3Sd0xyH
- eBay: ebay.us/qiCrSH
- RepairClinic (OEM) bit.ly/48OHmCm
Washer Bearing Kit and Tool Set (Aftermarket)
- AMAZON: amzn.to/3ETi5IV
- EBAY: ebay.us/8gQHTD
Find Some of Our Faves on Our Amazon Storefront!! ➡️➡️ amzn.to/3xPs2rI
Sign up For a FREE 30-Day Trial of Amazon Prime and Get Your Appliance Going Faster! CLICK HERE: amzn.to/3BA7Erj
If this Video Helped you in any way, Consider Leaving a Tip:
- Buy Me a Coffee: buymeacoffee.com/diyrepairsnow
- PayPay: @diyrepairsnow
- Venmo: @diyrepairsnow
**If you are interested in Purchasing the Tub Removal Tool, Go to: diyrepairsnow.square.site/ - Free Shipping, U.S.A. Only (OUT OF STOCK)
**RepairClinic Offers Original OEM Parts and 365 Day Return Policy. Visit them HERE: www.anrdoezrs.net/click-10023...
Warning: Please Be sure to Unplug Any Appliance Before Starting any Repairs! This video is to help DIY's do the repairs themselves, at their own risk.
Thanks for Watching and be Sure to Subscribe for more HowTO/Repair Videos!
- DIY Repairs Now
**Disclaimer: This Post May Contain Affiliate Links. These are in No way an Extra Cost to you, However If you use them, You will be helping out this channel.
After watching this video, I told my wife that I am going to try and repair the failed bearing. I also told her to get ready to buy a new washing machine. :)
Good luck 😂😂
If she's anything like my lady, she's crossing her fingers for the new machine!! 😁
I'm in the same boat my friend. My wife seems to think money, dryers, washers all grow on trees........Women.....
@@shanecthompson77 uyyy tuuuuuuuuuuu
Update?
Great video, one helpful hint for people with a stuck tub. You dont need any extra tools just skip that step and go on to hammering our the shifter rod from the bottom side with the tub and all. Once out the tub is free, pull it out and then hammer the shifter out of the tub from inside the tub. Tub puller is only needed when you don't want to replace the bearings.
Dude! You saved me a ton of money! My girlfriend was having a fit to buy a new washer which cost between $700 - $900! I told her, for Heaven's sake, buy me the kit and tool and I'll do it and save you some serous cash! If I fail, nothing ventured, nothing gained, right? Thanks to your video I did the job no problem! THANK YOU!
Most repairmen would quote this repair very high encouraging the owner to replace the washer. This is the kind of repair that a homeowner does themselves when saving money is more important/critical than convenience. Excellent video btw!
By far the best step by step video replace the Bearings and put the machine back together. Thanks so much!!!
Just gotta say 6 yrs later and this is still helpin folks man, better explanation than most and even included your mistake AND the correction with a forewarning so we dont have to hassle with the order of when to add the washer.... Thanks to this video i was able to find it was just debris in the bearing and some pb blaster andspinning by hand was able to work it out of the bearing way with out having to replace bearings or the otherwise fine spindle.... The plastic magnet ring in the bottom beeded cleaning too as the debris was STARTING to erode the plastic ruffles that match the spindle
This is one of the BEST step by step explained videos I have ever seen. It walked me through what I needed to do and what I need to be aware of to complete my job. Thanks!!!
Thank you so much ! Great walkthrough ! i did it my self cost 136 $ canadien dollars, 5 day waithing for part and hours of fun. Bravos maytag MCT bought it 9 years ago. no more airplane in the house. Thank you again !
Absolute best example of how to replace bearings in Bravo and Cabrio units. Watch first. He teaches how not to make his mistakes. Thank you. Well done!
+David Kinman Thank you so much. Glad you liked my Video.
Agreed well done ny man....Well done very thorough!
This was a great video. My brother & I were able to do this repair very easily. It really worked out great with two people. I would like to say that we have a great deal of mechanical ability when it comes to replacement of bearings and seals. We used to repair scaffold hoists for a living. The step by step instructions were very good & helpful. This was the first time we have ever tackled this project. So, the video was very helpful. The only thing we regret was the cost of the Driver Tool. We are retired and probably could have done this job without the expense of the Driver Tool. But, without our Machine Shop, we felt that the expense was needed. We know how important it is to get bearings and seals lined up properly. The Driver Tool was able to do just that. Now, with that said.....Is there a need for others to share in the cost of a GOOD used Driver Tool which was used only one time and for only 15 minutes?? BTW, our repair was a total success. We could have NOT done it without this video. Thank you!!
My washer kept shooting kept shooting a code (F8?) and after watching a video from this channel I too almost bought the tool until I took a closer inspection with my flashlight and discovered an old wash rag stuck between the tub and agitator😅 That tool is not cheap saved around $120? It’s leaking water now but I think I’ll just buy a new one
You did a great job in making this doable for the average DIY guy. I am confident I can do this and save having to buy a new washer. Thanks!!!!!
Glad I could help! Thanks for Watching!
Excellent write up! Thanks for taking the time to do this. I was able to do my Bravos XL today with this tutorial!
Bro, this video was absolute gold - had to complete this exact repair on our Bravos & was a complete success. Followed your tips (eg: the washer one) and avoided any pitfalls. Thanks again for the awesome DIY support!
Glad it helped with the Repair of Your Maytag Washer! Thanks for Watching!
Much love! Your video gave me hope I could fix it. Took 4 hours the main problem was lining up the washer above the bottom bearing. It would always move and block the shaft. Either way old one was a gross and good time to change, no more leak
Thank you for the video. My washer leaked and sounded like a jet engine. With your help, its purring like a kitten. Did it myself in a couple hours with your help. Thank you
Great video. Replaced everything much quicker than anticipated.
One thing to note, the Bravos XL has 2 screws you must remove to open the top. Putty knife does nothing. Also, to properly tighten the stator, use a small T handle Allen thru the cap holes to keep it from spinning as you tighten.
Where are those two screws? I have been trying to get the top off and it is not coming off with a putty knife.
Thank you so much i ve followed your instruction to a T and 2 month later the washing machine is still quiet and functions perfectly, you saved me 300.00 many thanks again!
Your video was so helpful. I can't thank you enough. Everything went exactly like you described. The only added issue I had was getting the tub out as I had use a jack and a piece of wood (found this solution on a different video) but it was no big deal. The job took me almost 5 hours as I went very slow and took my time. Thanks again as my washer now sounds and acts like a new one and the wife thinks I can do anything now. lol
Lar
Thank you very much! My wife and I fixed our washer using this video. Excellent!
Thanks a bunch! Great video. Step by step. Took my time. The only thing I can say to others is not to tighten too hard when installing the new bearings. I bent my new "spacer" with the tool NOT allowing me to slide the new axle so had to use the old spacer. Well done dude. Sounds like a new washing machine again. Cheers.
What a great video, thank you very much for your help. This made my job extremely easy to do, your step by step instructions were right on point. I and a lot of people really appreciate your help.
Thanks again
Your video saved me a ton of money thank you. Replaced the seal and it’s been working ever since.
My washer had become completely unusable because the bearings had gone bad. Wouldn't even make it through a spin cycle. But I was able to fix my washer because of this video. Thank you so much for saving me hundreds of dollars as I thought I might have to buy a new washing machine.
Great video. A couple of comments.
1. My instructions did not say to add grease to the bearings, so i did not
2. You were the ONLY one, to call out the issue of the bottom washer seating improperly when installing the bottom bearing. I too set the bottom bearing twice and the washer was not seat correctly. However, the bearing press tool will seat all the way to the bottom and you do not know that the washer is wrong until you try to remove the press tool. I had to remove the bottom bearing twice. I found your video and the washer seated perfectly! Thanks
BTW if you seat the bottom bearing and the washer is not in the correct position, it will jam it up into the spacer, resulting in the spacer getting bent. I had to spend quite a bit of time to hammer it back to round.
Jim Acevez Yes that washer gave me a hard time, Thanks for your comment and watching my video.
Excellent step by step video! Allowed me to succesfully tackle what would otherwise have been a ridiculously hard job.
Thank you so much for your video. I ordered my kit and the instructions were far from easy to understand. They of course didnt show removing the basket and we spent an hour trying to remove the shaft and couldn't figure it out until I watched your video. Next time I'll pay the extra for the tool but we made it work with some washers, nuts and a threaded rod. Thanks to you we also figured out how to put the seal in correctly. Whirlpool and Maytag need to have better directions.
Thanks for your lifesaving video!
Dude You rock!!! this was awesome and you made it clear, and I especially appreciate pointing out the little problems to look for! fantastic!!!
Thank you so much, I did the job my myself saving a lot of money!! Everything went smoothly, awesome video!
Thank you so much for this instructional!!! Easy to follow and detailed!!! I found the parts and tool in a combo package for $100.00 but it didn’t come with directions. I used this video and did everything myself with little difficulty!!!
Donald Watkins. Where. Did. U get. The. Combo. Package
Great video, my friend. Gotta tear into mine tomorrow and helped me see what I'll be getting into. Thanks!
Great video of explaining the process and the mistakes he did and how to correct them. I just finished doing the bearings and seal, it works great. I do want to share an extra pointer. The bottom nut was pretty hard to get it started. I would recommend to try to make sure it fits smoothly before placing the shaft in the washer. Once, you can get it started outside of the washer, then when you put the shaft in its place, the nut will easily go on. That was an issue I encounter, but easy to address before you get started. Again, thank you for the video.
Thanks for the video it helped me troubleshoot a rotor position sensor fault code F51. Since the procedure to replace the bearing involves removal of the stator and rotor I could see what all of these components looked like before taking the washer apart. Big ball of dust fell out of the rotor assembly during removal, cleaned up rotor and stator and F51 code went away!
Great clip! I just finished the repair on my own machine and everything was sufficient except for the part on the tub removal. Another option is to use a jack with a strategically placed two by four! Other than that, well done and thanks for the video!
Thank you very much for the detailed video! Worked like a charm and now my washer is back from the dead! 👍🏻
Thanks for your video. Don’t think the grease is for the bearing, they are sealed. It’s for the top sealer
OUTSTANDING video. Thanks for walking me through this. Had no experience doing this kind of repair. Bought parts online and watched your video... step by step.. took me several hours. My Maytag Bravos sounded like a freight train during spin cycles and started leaking rusty water on the floor. Figured a bad seal ruined the bearings over time.. Everything worked well and I'm back in business !! Only suggestion I would make is that after placing the top bearing loosely into it's housing... that you unscrew the nut on top of the bearing press tool almost to the end (to give you more rod length) before placing through the bearing.
Thanks for your Comment, I am glad my video Helped you.
Bravo XL....sorted...Gracias Amigo! Great Vid
Many thanks for this video. It was perfect. Using it gave me the confidence to do the job even when gentle persuasion (via 4lb sledge) was required. Thanks again from the frozen Canadian north.
I really appreciate the time you took to make this tutorial. Well done and thank you!
Just finished doing this repair on my washer thanks to your video waiting for the sealer to fully dry then going to run a load thanks for the video super helpful
Great video!!!!!!!! . You are a very detailed mechanic . I will be experimenting with my loud spin cycle noise as soon as I order the kits .Thanks million.
Excellent video and sound quality. Well presented and very helpful. I'm about to go and start the job.
Thank you very much for taking the time to make/share this video good sir. You saved my young family hundreds of dollars with this tutorial.
I searched many "how to" videos on this job, and this was the clear and concise BEST. I owe you and your a dinner.
Washer works like a dream now.
Rob Kilcollins You're welcome thanks for watching my video ...
Adding my thanks here! Followed the instructions and fixed my machine for the cost of the kit and tool...about $80. I had one major hickup though..my upper bearing had basically exploded. When removing it, only half of the bearing came out. The other half had to be cut out using a Dremel tool. Nobody's fault, but a serious pain in the A$$. Once it was out, everything went back together seamlessly and now she's running smooth and QUIET! Thanks again
Josh Clark some advice for next time you run into something like that . pulley puller can grab the outer bearing race and pull it out
Thank you for this video. I change the shaft and the bearing its was so easy following your video
my wife she so happy
Benoit
Quebec Canada
Great video ! helped me complete my repair on my washer . Thank you very much
Thank you for this video especially the trick for setting to lower bearing!!!
Outstanding video & provided links in the description. I ordered the stuff by following the links and I'll start the job ASAP. Thank you!!!!!!!!!
Great vid man, now i can tackle my bearing issue. thank you.
5/5 video for this repair. If I lived in Tampa I’d hire this man.
My washer is making the bad bearing noise i came on youtube to see repair done you have done a good job and will be ordering parts this week Thank you
Thank you very much for this video. You saved me a bunch of money and you did a great job explaining everything. Can’t thank you enough for sharing the information
Thank you for this video, it helped me change out the bearings on my Bravos! It is such a relief not to have a jet turbine going on in the house!
Smart approach to this loud nagging problem! You saved me a lot of time, thank you.
You're welcome I'm glad I can help👍🏻👍🏻👍🏻
Thank You very much for the video. It was very helpful. I will be ordering my parts tomorrow.
July 2020 - Thanks. This was an excellent easy to understand and follow tutorial. Absolute must watch if considering this DIY repair.
Finally a video that has the same hub as my maytag. All the the other videos have the hub with the pin.
Hi, today I did the same repair to my Maytag washer changed the bearings and now it works like the first day I bought it ,NO NOISE like the jet plane ,Thanks Guys your video was very helpful.
STAGE1MUSICLAB how many hours did this project take?
Thanks for this video, it definitly made the job alot more easy than trying to do the job "cold turkey" ie; no video help! I had the very same issue with the spacer sleeve and spacer washer shifting slightly out of position which caused the shift shaft not being able to drop into place. If this happens to any of you DO NOT POUND THE SHIFT SHAFT DOWN! Looked closely with a flashlight and felt with my finger I could see the sleeve and washer were misaligned which ment I had to loosen the bearings slightly by tapping ever so carefully with the punch tool and shifted them back in alignment from the top (used a long screwdriver to move the spacer) then reinserted the bearing tool and retightened the bearings. Now I was able to slide the shift shaft down thru the bearings and finish seating with a few hammer taps on top of the shaft.
Thank you very much. EXACTLY, the same problem I am having.
Thanks for your time making the video! You saved our family a lot of money
Thanks, man. I don't my think my problem is the bearing but that's a great look at how that thing is designed.
One of the best if not the best video and bearing and seal replacement.
This is a great video. He’s step by step. Helped me out a lot. Thank you.
Nicely done, step by step, with the key points.
Great video. Thanks for the upload. I have the same washer and the same problem. Followed you video and just saved $300 at least.
The only problem I ran into was getting the stater hub off. The bolt was rusted on there and stripping the allan wrench hole out. Since it has such a flat profile and rounded, I had no choice but to use a dremel tool and grind away some plastic so I could get some vice grips on there. Even then, I had to bang it off to the last thread. When I put it back on the new one, I dabbed a little grease in there to help prevent that. It should still stay on there even with grease. It has a very fine thread. It's going to have to make many turns to come off.
Thanks again. Thumbs up!
Randi Rain thanks for your comment I'm glad my video could help....
Randi Rain I need some help guys
I am having to change this bearing again. This washer is a piece of crap. I filled it full of grease and water still got to the bearing.
Thanks for this. If you don't have the bearing tool you can use the old bearings, old seal and old shaft and a block of wood to push the new ones into place. Just don't get the old upper bearing stuck in the tub on top of the new one.
SHAFT.......not shifter!!! LOL! Great video, thanks for your efforts and time!!!
You’re welcome thanks for watching my video👍🏻👍🏻💯💯
You are the best! Very thorough! Thank you.
Dude! Great video! I'm up against doing a bearing job on my Mom's Maytag WTW6300WW0. Thank you for the heads up on the tricky washer. Rebuilding transmissions, I used petroleum jelly (dissolving grease) to hold tricky bits in place. Thank you for the reminder. lol.
Great work thanks much. That black gunk at the bottom of the inner tub and under the agitator stinks and the clothes don’t get completely clean. I disinfected it out it seemed the black stuff was moldy. Smelled much better. Your video rocks!!
Excellent video tutorial. Thank you for sharing your knowledge and expertise. Much appreciated.
Awesome video. Thank you for taking the time to make it.
you were spot on with that washer. it cost me a lot of time figuring that out. had i seen your video it would have saved me from turning the entire washer upside down. what a Pain in the a##
I had the same problem with that washer that is placed between the spacer and lower bearing. Made 3 attempts and on the last was able to correct it with the metal bar that comes with the tool kit. I like your solution better. FYI: Pouring a kettle of piping hot water on the "tub hub" enable me to remove a stubborn one.
For the most part this video helped! There are a few things to add to it though. There is an alignment hole in the stator that you can use for keeping the rotor from turning with a screwdriver while trying to take the nut off, and to make sure you have the right size allen wrench in there! This was my mistake and ended up tearing the rotor bolt up. Also you don't need their $200 tool to put the bearings in. If you have ever replaced wheel bearing races you can figure it out, and I actually use the shaft to line everything up straight. Also, be very careful not to break the tabs off of the position sensor, otherwise it'll be loose.
excellent tutorial. much appreciated!
Dude. What a great video. I've got friends in Tampa and will be sure to recommend you to them!
I also had trouble getting old shaft out, didn't get the press tool to get tub out. Great video, very well done, thank you for doing it.
One can use a bottle jack and 2x4's to pull the tub out.
@@Jake-by9ly my buddy and I almost tried that, we ended up pulling the tub and shaft out together then putting it up on two sawhorses and beat shaft out w several chunks of 2x4 (as the shaft proved tougher than wood) to a successful end.
Best video for this repair. Very detailed. Thanks.
Oh Man best how to video. Loved the easy instructions and video commentary this video should win an Oscar ! ❤❤❤❤🎉
FYI: It's not a "shifter", it's the "Main Power Shaft" or simply "shaft", or even "axle". Otherwise, great video! Excellent tip about the washer. This was my third time to change the bearings and (thanks to your tip) the first time I didn't get the washer jammed in crooked. Good job!
just used this video to replace mine, some advise for the next video would be to show close ups and bring up how some key parts go together. Like how the bearing looks when pressed in
WOW! Great video man! Very easy to follow. Thank you!
This is an excellent video of how "terrifying" a washer repair can be. I hope I don't have to do that job anytime soon; but thanks anyway.
Hey thanks for such a clear, easy to follow walkthrough.
How do I know when the shifter is in the right position when I'm driving it in? Can it go too far, or does it stop?
this machine doesnt have a 'shifter'! but the Shaft has a flange that bottoms out against the top of the top bearing. it is also possible to to overtighten the toot and drive the bearings in too far that the spacer tube and washer bind and make it hard to install the shaft. they should have s very slight freedom of movement before installing shaft. (i always check the washer has side to side movement but not up and down). the spacer tube and washer should be greased but not the outside of the bearings
Thanks guy. This helped tremendously 👍
Glad to hear it! Thanks For the Support!
All I can say is Great Job !!
+Janice Anmary thanks I'm glad I can help....
You're video is a great explanation of how to do this repair. I listened to the other video you made showing the diagnostic mode where you mentioned how it sounds like an airplane. My Cabrio made the same exact noise and I also described it as an airplane engine on takeoff. I thank you for sharing your knowledge and skill and thank you for patiently describing every step of the process. Now, I know I can do this repair. God bless you.
Thanks for your coming I really appreciate it💯💯👍🏻👍🏻
awesome, thank you very much for taking your valuable time to make this great video.
Wow nice video step by step I order the parts and seems like you made it vey easy for me to do this job .
I will leave another comment once I complete this task . Thank you for sharing this video .
Thank you. Great video!
Excellent video. Ordering the kit. Thanks!!!
Thanks for watching my video..
Awesome!!!!! One of the best this guy is… He knows his shit LOL great Great job thanks for helping us out 🤙🤙
Thanks for watching my video 💯💯👍🏻👍🏻
Very through video! Excellent!! I know I could do this if I need to! Keep up the great work!
Just wanted to say thanks, this saved me a ton of money
Steve Miller you’re welcome I’m glad my video can help💯💯👍🏻👍🏻
@@DIYRepairsNow fytttyyytyytfzzz zyyttyydddtytttfz zffydytydddtdffzzfdfdddtyytyyyfzzzffdyytyttzzddytytyyytfzzdfdffdttdftz zyffytdydfzzzdyyytfzzdfyyyydzzdddddttttdyddzffzfffffizzdftttytytyfzfddfyzztytfyyzzyydzdddfzzddtydzzdtdtytfttdzzfdttttddydtztzzzztttdttyyytzzzddddfzzzfdddtty6zzzzdtttzzzftt6zzfzzfdtttt6zzftdtttzztfdydzzzzzzfddtddtdddtdtdddtddtdtdzzddtdtty6dzz6ddtt6dzzdty6dzrzfdtttyzzzd6zzWelcome to Gboard clipboard, any text you copy will be saved here.Welcome to Gboard clipboard, any text you copy will be saved here.Welcome to Gboard clipboard, any text you copy will be saved here.Welcome to Gboard clipboard, any text you copy will be saved here.Welcome to Gboard clipboard, any text you copy will be saved here.Welcome to Gboard clipboard, any text you copy will be saved here.Welcome to Gboard clipboard, any text you copy will be saved here.Welcome to Gboard clipboard, any text you copy will be saved here.Welcome to Gboard clipboard, any text you copy will be saved here.Welcome to Gboard clipboard, any text you copy will be saved here.Welcome to Gboard clipboard, any text you copy will be saved here.Welcome to Gboard clipboard, any text you copy will be saved here.Welcome to Gboard clipboard, any text you copy will be saved here.Welcome to Gboard clipboard, any text you copy will be saved here.Welcome to Gboard clipboard, any text you copy will be saved here.Welcome to Gboard clipboard, any text you copy will be saved here.Use the edit icon to pin, add or delete clips.Welcome to Gboard clipboard, any text you copy will be saved here.Welcome to Gboard clipboard, any text you copy will be saved here.Use the edit icon to pin, add or delete clips.Welcome to Gboard clipboard, any text you copy will be saved here.Welcome to Gboard clipboard, any text you copy will be saved here.Welcome to Gboard clipboard, any text you copy will be saved here.Welcome to Gboard clipboard, any text you copy will be saved here.Welcome to Gboard clipboard, any text you copy will be saved here.Tap on a clip to paste it in the text box.Use the edit icon to pin, add or delete clips.Use the edit icon to pin, add or delete clips.Welcome to Gboard clipboard, any text you copy will be saved here.Welcome to Gboard clipboard, any text you copy will be saved here.Tap on a clip to paste it in the text box.Use the edit icon to pin, add or delete clips.Welcome to Gboard clipboard, any text you copy will be saved here.Tap on a clip to paste it in the text box.Tap on a clip to paste it in the text box.Tap on a clip to paste it in the text box.Tap on a clip to paste it in the text box.Tap on a clip to paste it in the text box.Use the edit icon to pin, add or delete clips.Use the edit icon to pin, add or delete clips.Tap on a clip to paste it in the text box.Tap on a clip to paste it in the text box.Tap on a clip to paste it in the text box.Tap on a clip to paste it in the text box.Tap on a clip to paste it in the text box.Touch and hold a clip to pin it. Unpinned clips will be deleted after 1 hour.Touch and hold a clip to pin it. Unpinned clips will be deleted after 1 hour.Touch and hold a clip to pin it. Unpinned clips will be deleted after 1 hour.Touch and hold a clip to pin it. Unpinned clips will be deleted after 1 hour.Touch and hold a clip to pin it. Unpinned clips will be deleted after 1 hour.Touch and hold a clip to pin it. Unpinned clips will be deleted after 1 hour.Use the edit icon to pin, add or delete clips.Use the edit icon to pin, add or delete clips.Use the edit icon to pin, add or delete clips.
Thank you for this video, I was able to fix my washer!!!!!
You’re welcome thanks for watching my video 💯💯👍🏻👍🏻
Thanks for this great resource! Question... my Maytag needs bearings for sure. Can the bad bearings stop it from agitating ?
Great instructional video. However my stator cover screw came loose after a few days. Added locktight and retightened. Problem solved.
Great job. Thank you
Thank you. This is very helpful.
Great detailed video 👍🏾
good video bro makes everything so easy