Dear this circuit is only Good for leds lights. Yes You Right the Capacitor Is Overcharged You can Use More Voltage capacitor. Overcharge Capacitor May punture after Some Time Sorry For That Dear. My Mistake
@@creativechannelpro371 I need to convert a drill (from battery to power) of 14.4v and another of 18v for which I need to have at least 8 amps. Using an ATX PC source as power.
@@cachoale-xs4cb better just making own battery i had same problem with lidi circular saw eating battery fast cus they crap .....cud use a boost converter off ebay 12 to 20v but because of the boost function drawing extra current (8amp 20v would be like 12v 15 amp from battery) ......be better going higher voltage and stepping down (buck regulator style ) mod the atx supply transformer to have a 20v to 30v secondary winding remove the 5v winding if not needed note the turns and multiply it by 6 to get the 30v but change the components associated to the 5v circuit x 6 the rating plus feedback circuit needs adjusting ......just idea tho lol
The world's best teacher
Very good
Thanks My dear
Wow super good work
Good job Bro!
Thanks bro
So nice
Good video
Thank you so much bro😊😊😊
How the capacitor with voltage rating 25 volt withstand output voltage to the magnitude of 42 ?
Dear this circuit is only Good for leds lights. Yes You Right the Capacitor Is Overcharged You can Use More Voltage capacitor.
Overcharge Capacitor May punture after Some Time Sorry For That Dear. My Mistake
Great video you are pro like 2
Thanks you so much freind
Hello, nice video, can this circuit take 12v in and give 24v out ? if yes, at how many amps ? thanks.
No bro this circuit cannot because this circuit good for leds only
@@creativechannelpro371 thank for answering :)
Welcome bro
Can we ran a motor with it
Cannot Sorry bro because its current is to low
Can I use this dc boost circuit to lighten up for a 40 volt dc led bulb? If it can, if there will be problem when I use the bulb for long time?
sorry sir yt not show me your comment sir zyada dher tak shayd na chalay
Can't i use the mosfet 2N60 bro?
So Sorry for late reply dear Yes you can Try
inner and outer diameter tiroid?
No matter dear use any
Bro can i use 13005??
No bro MOSFET is good
Any mosfet??
Most n channel MOSFETs work
@@creativechannelpro371 😁😁
I will try thanks 😍
Nomber mosfet????
ola boa noite o amigo ai poderia mi dizer quantas horas é a duração da bateria nesse circuito?
Pls define me in English
out put 40v ?? use 25v capacitor ?????
Great bro You are right pls use above 40volt capacitor my capacitor heating to much sorry for that
What is the maximium power it can handle
Friend this is good for leds only you can easily run leds strip
Sir, you are using 18-0-18 in toroid winding
But if we are using more no. of toroid winding (like 50) what effect on project
No to much effect voltage not increase and amp not increase
@@creativechannelpro371 where i put potential meter and how to increase amp and volt?
Hi
☺️ Hi dear friend
Use some solder
Put some solder on it.
Thanks friend OK friend I try to improve my soldring
My friend, To regulate it: Where do I place the potentiometer and what value? and How many amps are there at the exit?
Friend output voltage is good but amps are too low at least 200mah
Friend you need to connect voltage regulater circuit on exit
@@creativechannelpro371 I need to convert a drill (from battery to power) of 14.4v and another of 18v for which I need to have at least 8 amps. Using an ATX PC source as power.
@@cachoale-xs4cb Yes friend great idea computer power supply is good in amps
@@cachoale-xs4cb better just making own battery i had same problem with lidi circular saw eating battery fast cus they crap .....cud use a boost converter off ebay 12 to 20v but because of the boost function drawing extra current (8amp 20v would be like 12v 15 amp from battery) ......be better going higher voltage and stepping down (buck regulator style )
mod the atx supply transformer to have a 20v to 30v secondary winding remove the 5v winding if not needed note the turns and multiply it by 6 to get the 30v but change the components associated to the 5v circuit x 6 the rating plus feedback circuit needs adjusting ......just idea tho lol
40v output voltage, 25v capacitor :D :D NoT Like !
No too much problem of capacitor voltage uf matter
@@creativechannelpro371 wrong
@@creativechannelpro371
I've seen capacitors go pop due to over-voltage.
😊😄 Yes my capacitor also pop up due to high voltage joint two capacitors in series bro
Thanks for comment
@@creativechannelpro371
It is fun to hear them squeal then go pop though. :-D
Can i make using transformer mobile phone charger ?
Yes friend you can use mobile phone transformer
But first you need to unwind and rewind again like a vedio
Hello friend, Can i use a Potentiometer to adjust the voltage?
Yes friend you can
@@creativechannelpro371 where i put potential meter and how to increase amp and volt?
Friend if you want to put potential meter you need to make voltage regulator circuit
I can use p55 as it
You can use N channel mosfet
Thanks but I have p55
And it make 3.7v to 12v but how I can make 32v for cob led chip
And how many amperes are required by this circuit
Bro better you buy step up modules
How many amp in this circuit
My friend really sorry for late reply friend output amp to low at leat 200mah sorry friend
Essa música já está chateando
Bro not understand your language
Unlike for unnecessary music
Sorry bro
Sir, 56 v ko 24 v kaise change kare?
Sir you want to change 56 volt to 24 volt use 7824 regulator
56 volt DC ha
@@creativechannelpro371 sir ,56 v dc hai. potentiometer agar use karna chahe to kitne kilo om ka le?
wire diameter ???????
0.5mm to 1mm friend sorry for late answer
Kitna Amp hai
100-200ma
Kgra
Make it variable
Thanks for comment friend OK I try latter
is not working
Thanks for comment friend its working please check the circuit diagram and check your all components
MOSFET you use friend
You can use irf3205
Output is lower than the battery power
Is this problem of mosfet?
What used in the video?
with a 12 volt power supply it is shorted
Yes friend its works on 3.7volt battery or 5 volt only sorry friend
Hello friend..
What parts to change, if use 9V - 12V In Power Suply
(e.g. 9Volt battery Vin) ,, Thankyou ..
@@permudahsaja4179 Use a normal transformer with a center tap instead of a toroid. Better insulation.
where is the schematics
Thanks for comment friend schematic on time 1.19 to 1.24
Dynamo laga ke rickshaw charge nahi kiya ja Sakta
Nahi bro amps boht Thoray ha
@@creativechannelpro371 amp ko kaise badaye
Bhai amp thoray hotay ha increase nahi hotay sorry
Sir AMP
Bro 100_200ma
اسکول،بجای این آهنگ مسخره، مشخصات اقلام مصرفی و یه دیاگرام از کل کار مینوشتی!!!!!!!!!
Bro don't understand language
its just joule thief
Yes Upgraded joule theif
fake video
Friend its not fake its working please check your circut again and check your mosfet. Rewind torodiol may bi wrong winding
Not fake
Yes bro you are right not fake it is 100% working
But some people do mistakes in circuit diagram and winding of tesla
Contact me on Whatsapp may be I help you
My no +601169439048
bro you not show input only output and looked at both connections lol 8:50
Sorry for my mistake bro input 3.7volts outbut at least 24-30
Thanks for comment
Verry good
Thank you so much bro
Fake video
No friend 100% real please check your circuit again or use correct components may your winding is not correct if need help whatsapp me +601169439048
Sub component sahi hoke bhi pura circuit jal gaya bhai
Bhai app na input zyada to nahi de diya
Or winding par bhi depend karta ha
Input 3.7 v diya tha pura circuit hit hua