The guy who had 68v on the 35v capacitor was lucky that the capacitor didn't explode, put a higher voltage on the capacitor and if the coil squeaks, it means that it is very loaded and the coil probably has too low a maximum current, if the coil gets hot, change the coil
you can use the same circuit to convert 5V to 12V. Use the potentiometer to adjust the output voltage to 12V, then add a 12v zener diode at the output. The current is low but it will still work.
Hi, i want to ask about the components that are used, irfz44n mosfet, 220 ohm Resistor, 2200uf/35V capacitor, what value of inductor and diode or which type, and 10k pot? And how can i decrease the output?
You can use high power N channel MOSFETs to boost voltage without too much heat problems. I used IRFz44N MOSFET for my project. It shorted from a high voltage feedback in the coil bc I don't have any zener diodes to protect my MOSFET from blowing up.
HI, I could use other transistors like H22 13866 or P133009 or LT5250 or SB3040PT or RC3009 or MOSFET S20C45C instead of irf3205 ??, thanks so much in advance.. best regards!
Thank you very much bro❤
Its working very well🎉
I made a super bright emergency light with this💖💖👍👍
welcome bro thank you.
Great work mine boost to 76v without potentiometer from 3.7v but drops as soon às i put even a simple load and doesn't work why?
🤔
The guy who had 68v on the 35v capacitor was lucky that the capacitor didn't explode, put a higher voltage on the capacitor and if the coil squeaks, it means that it is very loaded and the coil probably has too low a maximum current, if the coil gets hot, change the coil
1 st good video and experiment
welcome and enjoy
Good but amp.kaise badhaye.please reply.
5A
Good job 💥🤟🤟 ...thanks for shearing 🙏💛
welcome
Very nice video ! Can you please show how to make 12v to 48v to make work inverter from battery. Thanks.
ok i will try
Nicely done 👍 how do I make one to convert from 5v to 12v thanks in advance ❤
Please wait
@@homemade_101 ok thanks
you can use the same circuit to convert 5V to 12V. Use the potentiometer to adjust the output voltage to 12V, then add a 12v zener diode at the output. The current is low but it will still work.
works great! BTW, i was wondering, if I use a lower trigger voltage MOSFET, would it be capable of stepping FROM lower voltages? say, 1-2.5V?
Yes you can!
Can i use this to boost voltage from 18V Solar Panel dc voltage to get 300V Dc so get ac 230v Product can run ??
@sumitd4u Not all devices are capable in powering house appliances. They run on AC but you can use light bulbs and phone chargers on DC.
Hi, i want to ask about the components that are used, irfz44n mosfet, 220 ohm Resistor, 2200uf/35V capacitor, what value of inductor and diode or which type, and 10k pot?
And how can i decrease the output?
Hi again, I have 0.6mm of wire. How many turns i can use for the inductor?? Thanks for allí. Great proyect
40 runs all 20T 0 20T
Work kar raha hai bro😊😊😊
thanks borther
Is it necessary to use potentiometer in this project?
YES
If dc input 0.5 volt - 2 Volt DC, what is component can i use for booster converter?
2v ok yes
12turn inductor can be bought or made?
made it
can i use z24n or 2x z24n ????
yes you can use
@@homemade_101 1x z24n ??? ... BUt thank you so much
Can i use " ITA12N65R n channel mosfet ...instead...
yes
Yes, it's working now...
Thanks 😊
You can use high power N channel MOSFETs to boost voltage without too much heat problems. I used IRFz44N MOSFET for my project. It shorted from a high voltage feedback in the coil bc I don't have any zener diodes to protect my MOSFET from blowing up.
Can I use 10 k trimpot instead of variable resistor
ok
Ive made it .. But the mosfet cant stop heating.. How can i fix it? tnx bro!!!
It is nomal, use heat sink
Add a 12v zener diode from gate to source of MOSFET to protect high voltage from killing the MOSFET.
Can I use 4700uF 16v capacitor ,IRF3205 mosfet and 1N4007 diode for this?
yes. but not recommend Diode and capacitor voltage
could you pls tell me why is there background noise when the boost is working, where is the sound from and how to decrease the noise ?
it is normal. induction sound
How much ampere brother.
Please explain.
sir, how to make with this boost converter flyback driver?
I think can do it
can I use a 10A10 or MUR1540G for the diode?
ok
Con eso elevó el voltaje pero si el amperaje es bajo también me funciona para elevar el amperaje lo digo por las placas solares
yes low amper 5A max
HI, I could use other transistors like H22 13866 or P133009 or LT5250 or SB3040PT or RC3009 or MOSFET S20C45C instead of irf3205 ??, thanks so much in advance.. best regards!
can't. MOSFET only.
OK, only mosfet, but I can use MOSFET S20C45C? thanks again.
Use more than one capacitor bcz when the load is higher the voltage drop at 3.7 again
THANK YOUR ADVICE
@@homemade_101 Welcome 😊
Hi, what Is the section in mm of the wire to create the inductor?? And the diammeter of the toroidal ?? Thank you
Can you tell me the diammeter of the wire and the toroidal to create the inductor??
1mm, 2cm
@@homemade_101 Ok, if i use for example 0.6mm i need to reduce the number of turns or not??
I can use irf630mosfet for this. Please reply
yes you can
Thank you for reply
Chào bạn.video rất hay.ban cho tôi hỏi đầu vào dung điện đc 12v được không? Xin cảm ơn!
dùng tụ điện 35V
Ye circuit kitna der Tak chal sakta hai
it is depend
Hola lo hize exactamente igual pero mi transistor se calienta y qué será lo que esta mal?
G-S connect 10K resistor and use heat sink
@@homemade_101 gracias ya funcionó perfecto 👌 un chingon eres hermano✌️👍
its boos the amp ?
5A
Good video, you can share the diagram
OK i will send tomorow
Circuit diagram 👉 drive.google.com/file/d/16eFvt-oyOp4ul343Uy-lTJ4bbMdWeu8l/view?usp=sharing
@@homemade_101 thanks bro
Ok cuon cam khu nhieu tot......!
thank you
What Is the value in Henry of the inductor?? Thanks
0.11mH 0.3 Ohm
Thank
Nice video 👍, can you give the circuit diagram? And I want to ask, how many winding the inductor? Thank you
Please wait
drive.google.com/file/d/16eFvt-oyOp4ul343Uy-lTJ4bbMdWeu8l/view?usp=sharing
Dc 775 motor chalage isme please reply
??
Where is that hissing sound coming from. From Capacitor or Inductor?
it is inductor
@@homemade_101 Can I supply this circuit with 5vdc if i don't have the 3.7vdc?
yes 5V ok @@century_centure
How to make the inductor you used
Inductor value
0.12 mH
And can it work with 5v direct from 5.5v Solar panel? Kindly reply to this please.
yes
@@homemade_101 I can see you have already answered my question. Thank s alot Bro.
is me 12V 1.5AMP input to 12V 5 AMP output circuitdiagram milega sir
No no. 3.7v to 5v input
@@homemade_101 sir ye work hi nahi kar raha kya karu 3.7 V input deta hu to bass 3.4 hi output aata hai ic bhi sahi hai fir bhi sir
Max current?
5A
@@homemade_101 thanks.
can i use ti wifi router
don't bbro
How many henery inductor brother
30uH
@@homemade_101 will a 5millihenery work i salvaged it from old cfl driver circuit
its not working bro 😢 me banaya ye nahi aa raha output bass 3.30V input deta hu to 3.40V Output hi milta hai potentio ko gumata hu fir bhi not work
This is working well. change inductors and mosfet
@@homemade_101 kitne size ka inductor use karu
How to delete the noise ,that noise every nigth is crazy
it is normal
Que diodo usas que numero
5A diode
I will just buy 2 more batteries 😁
it is no problem 😉
60v cannot give full illumination to the 12v car lamp...😁😁😁
yep
Hello bro can you make h bridge circuit that convert 310dc to 220v Ac plz
I haven't idea it. I will try
Hello baro waht led is no thing real to car light bulb baik indecatr bulb .waht is led .but led 1.5 volt .
Working volt 2200uf 35V step up 60V DC danger❗ of kapasitor
no, this circuit is safe. use a switch
Diode ka name kya hai
1N5401
Joule thief circuit 🙂
yes 12.6v
3.7v to 12v ❌
3.7v to 68v ✅
Solution?
i don't know
ทำแล้วยังไม่สำเร็จครับ มอสเฟตร้อนมาก
sorry
Y it make noise... ?????????😮😮😮😮😮😮😮😮
it is norml
Kepala sangat sakit lihat vidio ini karena terlalu cepat bagi saya pemula.
😮💨
Bo loc thanh........?
🤔
Маленькая сила тока. Мне больше вот эта схема нравится: ruclips.net/video/S_WAZnX_v94/видео.html
Ok ❤
enjoy
генерация срывается , не показал как мотать в какую сторону и каким проводом . нет стабилизации на выходе . схема отстой! ! ! !
what bro
Adjustable power Supply: ruclips.net/video/1tJxmAp36Cg/видео.html
Can it give constantly output 12volt 5a in small load
@@howtomakemoneyonfacebookpa2747 yes try
35 to 65 ☠️💀😇
sorry
No Good, Where is schematic
this is a very simple circuit.
How much ampere brother.
Please explain.