How to Replace Rear Brakes 2017-Present Ford F-350 Dually
HTML-код
- Опубликовано: 25 авг 2024
- Shop for New Auto Parts at 1AAuto.com 1aau.to/c/387/b...
Brake pads wear out over time, much like tires, and need replacing, on average, every 50,000 miles, with variations depending on driving habits and environment. Brake rotors may also need to be replaced if they are warped or grooved. Often, it’s safer and more cost effective to replace pads and rotors at the same time. Squealing or grinding noises, or wheel vibration are all symptoms of worn brakes. This video shows you how to install new, quality TRQ brake pads and rotors on your 2017 and up Ford F-350 Super Duty.
• Check here for more videos on the 2017+ Ford F-350: • Ford F-350 2017-2020+ ...
This process should be similar on the following vehicles:
2017 Ford F-350 Super Duty
2018 Ford F-350 Super Duty
2019 Ford F-350 Super Duty
2020 Ford F-350 Super Duty
2021 Ford F-350 Super Duty
2022 Ford F-350 Super Duty
Tools you will need:
• Flat Blade Screwdriver 1aau.to/oa/1AXA...
• Pry Bar 1aau.to/oa/1AXA...
• 16mm Wrench
• 18mm Socket 1aau.to/oa/1AXA...
• 21mm Socket 1aau.to/oa/1AXA...
• 24mm Socket
• Brake Caliper Compressor Tool. Dual Piston. Pump Style. 1aau.to/oa/1AXA...
• 3/8 Inch Air Impact Gun
• 1-1/8 Inch Socket
• E18 Inverted Torx Socket
• 1/2 Inch Breaker Bar 1aau.to/oa/1AXA...
• 1/2 Inch Ratchet 1aau.to/oa/1AXA...
• 3/8 Inch Drive Ratchet 1aau.to/oa/1AXA...
• Ratchet 1aau.to/oa/1AXA...
• Swivel
• Torque Wrench 1aau.to/oa/1AXA...
• Block of Wood
• Brake Fluid
• Brake Grease
• Brake Parts Cleaner
• Cloth Rags 1aau.to/oa/1AXS...
• Gear Oil
• Gloves 1aau.to/oa/1AXS...
• Liquid Thread Locker
• Rust Penetrant
• sanding disc
• Assistant
• Center Punch 1aau.to/oa/1AXA...
• Drain Pan 1aau.to/oa/1AXA...
• Hammer 1aau.to/oa/1AXA...
• Jack Stands 1aau.to/oa/1AXA...
• Razor Blade / Gasket Scraper 1aau.to/oa/1AXA...
• Vise
• Wire Brush 1aau.to/oa/1AXA...
Subscribe: / @trq
Check out our playlist:
Ford F-350 2017-2020+ 4th Gen: • Ford F-350 2017-2020+ ...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts
√ *Do it Yourself*
√ *Save Money*
Thank you guys, this is Awesome guide! Im ready to order parts from your online store, but I need also additional parts as bearings and seals. I didn't find it on your site. can you add full parts list for this procedure? Or make replacement kit for rear axle that will include seals, bearings pads and rotors.
This video made me feel a little bit better about why the dealership charged me so much for brakes.
I wish i could find a mechanic half as thorough as you are. You are a true craftsman. Ty for this video man, really helped me out with my project.
Wow. I own a 2013 F450 and need to change the rear brakes but did not realize how much work was actually involved. Thanks for the video.
Parts are expensive
Its not a a bad job at all to do in an afternoon boss! Just eat your weeties for breakfast cuz although its not a bad job its a tad on the heavier side lol
Outstanding job at making this 5-star instructional video! One of the very best I've ever experienced on RUclips. Thank you very much for your effort at putting this together.
Great no nonsense video, With this clip I think I could 'Do the job' , thanks for posting, good camera and lighting work 10 out of 10. Don.S
Gotta love having a proper seal installation kit with the right sized bushings! Good job getting that seal seated without damaging it. I know I would have crushed it haha
Excellent, professional quality video! Every single step explained in detail.
Well explained and thank you for saying the torque settings as you went.
Great video. Just want to make a recomendation that you crack open the bleeder screw when you push the brake pistons in so you dont force any dirty fluid back into the system.
+Eshedal74 Thanks for the tip! We'll pass this info along to our production team. 1aau.to/m/Shop-TRQ
Great idea!
Will that require us to have to bleed the brakes?
I'm a newbie when it comes to the big trucks..
Thanks for the video. Tried to upsale this job on a used F350 I was processing for a dealership. They said no and wholesaled it back to the auction with it. Now I know what I missed.
This is the best video explaining how to do the rear brakes on my truck. Thank you.
You need to grease the seal before installing. It would also make sense to use some high temp grease to grease the bearings until the gear oil will fully supply them when you start driving.
+Ewald Rindlisbacher Thanks for watching our video! 1aau.to/m/Shop-TRQ
This video is very informative. Very helpful for a step by step, while doing a job
+@rynely1 Thanks for watching. Buy the part in this video on 1AAuto.com: 1aau.to/m/Shop-TRQ
One more thing, those salty areas like the coast and northern country are hell on these wheels and axle center. We stated using a mild coat of grease when installing, so far the come backs for tires and or brakes or coming off Way better.
Very professional and well executed! Explained as well, keep more videos coming. Thx!
+Phil B G Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-TRQ
Use axle bearing grease where he uses vaseline and use alot of it. Fill the cavity in where the spring is. Id rather know for a fact that spring wont move then habe to take it apart again. Ive learned the hard way. Done dozens and dozens of these. Also. Instead of going nuts with the impact on the e torx bolts holding rotor to hub I've always gone and torqued those bolts to the same spec as wheel lug nuts. And on this truck should be 150-165. Good luck!
heal bar to pull seals life saver
After watching this video I don’t think I want to own a DWR anymore. I’m good with. SWR.
But nice and informative video BTW!
I like your videos--precisely what DIYs need. I was looking for some direction of how to remove rear output transfer case shaft seal on my 2016 Ford f250. It has a leak from the output shaft.
You are taking the chance of damaging the hub seal area by using the pry bar and air hammer. I’ve literally done 1000s of these by using end cut pliers. Easy as pie.
Also a seal driver or a same size piece of tubing works better for seal install.
Not getting those wheels off that easy in the north lol.
Upsets me nobody uses torque wrenches.
Amazing I love to do everything on my truck and cars thank you for the video it’s very well explained
using this video as a reference since the rear bakes and axles are virtually identical to my 1999 f350 superduty dually and i do not have the e-brake for some reason.
I’m having a hard time accessing the rear passenger adjustment its the on the opposite side
Is he going to bonk it????? Lol!!
What is the part number for the 4 point locking nut tool you used? Thanks for the video
W83008 Amazon. 2 3/4 . Or Napa has a equivalent one
Great video! I appreciate the clear instruction with each step. I have a 2017 f350 4x4 6.7, single rear wheel. Are the torque specs mentioned the same on the single rear wheel trucks? Thank you.
I am a little bit concerned here, why use a Vaseline instead of the regular grease.
Hi there i just want to know if i need to do grease pack on bearings, thanks
This same procedure works on a 2008 F350 also. All the same parts.
I enjoyed the video but the rear axle retaining bolts torque spec is 80 ft lb, not 188! Please fix this in your video or take it down so somebody else doesn't ruin the rear hub like I just did. My fault for not checking the torque specs myself.
Yup. 188, it is not! Plz correct it. I bet I am not the only one to torque it that high after watching this video. In the video, u don't look like u r doing that high either. U just state "188".
I can see that you love what you doing just like me 🙏🙏👌👌👌👌👌 but I’m just a Beginner
This is where I do one side and go "eh the other side is probably ok"
Muy buen video broth pero seria bueno que explicara como sangrando tambien
Great job.🏴🏴
I don't tell anyone what to do but, I use a seal tool, rent or borrow or own it,, Second I pack a little grease on my bearings because, I change the diff grease and this way you have a positive lube on the bearings when you roll out, Mind you, I and my buds ease out to a ditch or lean and let the new oil or grease run to each side and then come back and top off. REASON>>> In the early 80's we seen a lot of oilfield company's running these jobs themselves and they was having bearing failure. Being at a Ford garage we questioned the job, What I recommended was not what they did. They actually was running a dry or semi dry bearing to long right of the bat. Axle, not that what you did want work with a Love tap but not recommended. Usually one good deadblow to the center of the axle face will pop that axle right to you, it might take a couple but never the back face of axle. Outboard style drums and or rotors have changed the game A LOT. Hope someone sees a tip or advice hear.
Thanks. Very detailed. Will help a lot.
How do you adjust the e brake on the passenger side? It don’t look like the side you did. The cable is were the hole should be to back the e brake off!
Do you have to remove the axle to change rear brakes
Great work buddy 👍👍
Looks like your doing all this in a shop w ac. Must be nice 😂 go do all this in a 95° shop
you could only WISH the dealer did it like that ................ nice job !! ,, the reason why I could never make book time .....
+Ironworker FXR Thanks for watching our video! 1aau.to/m/Shop-TRQ
I was thinking the same thing. Would the tech take all those extra steps to clean mating surfaces and other steps this guy did. I highly doubt it. This was a job well done.
How do you know or confirm that the orange/brown seal or what colour is it that is sitting on the bearing that you start installing at 9.00 minutes that you used a wood to beat in is well seated or should I say is properly installed.
Just did new pads and rotors 2015 f550 I didn't add gear oil like you did at 13:10. I was wondering if I fill the rear end filler plug will it go down axle to these bearings? I really don't want to take it all apart again. Thanks
Anyone else break a axle shaft bolt around 100ft/lbs they started stretching not tightening no way 188ft/lbs is the correct spec
Lol that definitely wasn't right
Whoa you have to pull the axle to change the brakes. Wow
Will this procedure also apply to a 2016 F-350dually also what is the part number of the tool needed to take the center bolt off
Great INFO
Great video!!!!! Thanks.
Doing this job now. Unfortunately, mine has a grooved inner ring for what I assume is for ABS or a speed sensor I can't get off the ring or find a part to replace. I have 2014 Monaco Motor home on a F35 frame chassis. Any ideas?
Great great video helps a lot
Excellent video👍👍👍👍
curious as to why not install new bearings while you have them out
No need if they look good. A visual should be fine on a truck.
Will this process be the same for a 2008 F-350? Thank you.
TORQUE AXEL BOLTS TO 75 FT POUNDS HE STATES 188FT POUNDS WILL STRIP YOUR HUB
Excelente trabajo saludos.
when removing the hub locking nut, sorry is the pass side reverse threads or standard
Are you going to do the passenger side as well.????
never heard of a seal driver eh
PN 205-1070 Dana axle
205-1069 Ford axle
$300 a piece. No aftermarket options. Backordered until December.
I had to follow his hack instructions after I met that brick wall.
Hi, I want the name of equipment that you used it to open Lock Nut. Thank you
What size is the Spindle Nut Socket? I’ve seen a couple different sizes. I have an 04 F350 super duty dually king ranch 4X4?
Loving bonks
What is the number of this big socket
Would it be the same for a 2017 F-550?
Can you tell me please what the silver part on minute 12:49 called please?
And how can i find it on your website?
Does it call rear spindle or what ?
He didn't pack the bearing
They don’t need packed, they’re oil filled bearings.
Parking brake could have used some new springs. Those old ones are rusty and will snap.
What's that's socket drive called the 4?
your doing the driver side correct,,,lefty loosey, correct,,,, what about the passenger side ,,is it the same OR is it reverse thread
+taterhead 3e The threads should be the same on both sides.
I think ill just pay a shop to do this lol
How much did the customer pay for this job? Also did you do the front brakes? Thanks loved the video. 🥰🥰😊😊
I just did this on a 2018 f450 and now there’s a squeal when moving any idea what it could be, I just rewatched ur video and realized I didn’t put any vaseline on the seal would that cause that, do I have to take it back apart?
Did you find out what was causing that squealing?
So do the drum brakes assist the disc while stopping? Or do the discs work alone while braking?
+james richardson On most vehicles the drum brakes under brake rotors are the parking brakes. Thanks for watching our video! 1aau.to/m/Shop-TRQ
nice video
+taterhead 3e Thanks for watching our video! 1aau.to/m/Shop-TRQ
On my 2020 E450 the top caliper bolt can’t come out. The springs are in the way. The only way to replace the brake pads is to remove the bottom caliper slide bolt, pry the caliper up, remove the old pads. Then push the caliper all the way in towards the springs, then lube the slide pin as well as you can. Then put everything back together. How in the hell do I get those top bolts out?
remove the caliper bracket
I have the video how top do it check my page
13:10 yeah buddy I agree
+Phillip Drake Thanks for watching our video! 1aau.to/m/Shop-TRQ
At 1:40, what are you prying against?
The old rotor foo
B O N K
How much should this job cost per side at a shop?
+Matthew Bolt Thanks for watching! We do not have that information available.
that means hold to your socks.
Not a regular 50 dollar break job lol
My rear tires are wearing on the inside how do I correct that
Lube you glide pins. Maybe flush out you lines and calipers
@@corysturgis6660 I'm not an expert but I think it would have something to do with the suspension.
Screw that i will stay single tires on my F-350
I can't understand ,why you have removed a hub, to change the brakes, unless customer told you to change the rotor ,otherwise no need to do all of this to just change the brakes ,to change parking brakes, yes it is need to do all of it
Dude I would NEVER Let you Pry on my Wheels like that. No Sir Man. Mine come off just fine from 2 inches off the ground.
Also, did you just say Veer-icle?
My truck is a 1999 Ford F-350 dual it’s the same process for my truck??
+El Tigre This procedure might be different for your application. We do not currently have a how-to video for this particular year, make and model. Thank you for asking! 1aau.to/m/Shop-TRQ
Squirt Squirt 😂
13:09
AAAAH PACK YOUR BEARINGS AAAAAAHHH
A chisel. Woe. Yikes
188 foot pound? that is too much🤔
rear axle shaft bolt
I was thinking that seemed high too.
Do not torque the shaft bolts to 188 ft lbs his crazy lmao
Could you please show me any owners manual, or driving manual which states "Emergency" Brake. I have only seen then officially referred to as "Parking Brakes". I know they can be used in an emergency, but with any Ford Heavy Duty, if I had to use mine while towing a trailer, I know they would not be able to stop the truck in an emergency. You might want to check with your Lawyer to find out if you referring to them as an Emergency brake, if you are exposing yourself to a liability if a person has a crash and they thought you telling them it is an Emergency brake, if you could be held liable for damages suffered.
+Skyhawk Sailor While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
Shut up karen.
LOL!!!!! come let me show you how to actually do these,,,,,
This video has the wrong title. This is replacement of rotors, not brakes