Setting up a Dillon Powder Measure for Pistol cases
HTML-код
- Опубликовано: 4 окт 2024
- Setting up a Dillon Powder Measure for Pistol cases
Extreme Reloading shows the proper way to setup your Dillon Precision powder measure for straight wall pistol cases. If you have any questions please feel free to comment below or you we can also be reached at 888-702-2341 or sales@extremereloadingnv.com - Хобби
it's 2022 and this is still the best video on how to get the Dillon ready
You are the only video that explained this set up in detail.Almost all others just like to hear themselves talk but scant on info.For a novice like me,you explained it so well that it is idiot proof!!Thank you very much!!!
triggersafe1 Thank you! I’m glad it was helpful for you.
This is a great video on the Dillon with good demonstration of the parts you are discussing. Thanks for the lessons on setting up the Dillon powder measure.
This is a good instructional video. Red hair, black, hair, and blond hair are still units of measure.
The primer in the case backwards is a good idea 💡 I’ll definitely be using that hack for my Dillon
A Dillon trick is to tighten the thumb nut that is on the end of fail safe rod until it will just let a business card pull through between two coils of the fail safe nut spring. This will ensure correct return positioning of the powder bar.
if you want 3.2grn multiply 3.2 x 5 and weigh 5 charges at once to get a more accurate powder drop. keep weighing 5 till you reach your target (3.2 x 5) +- .1grn
This was more helpful with my problem than was the Dillon website.
I just watched a great video on "press stretch" Basically, the press stretches when you size a case vs. when you don't. So, if you do your powder charge with nothing in the sizing stage, it's going to flare a little more than when you set it up. Probably not relevant to pistol rounds, but definitely on rifle, especially for precision bullet seating. Good video, man!
@@curtislong1987 Yea, you make perfect sense. Thanks
Great video it really cleaned up a few rough edges. I had. Thank you.!
I found it much easier to install the dies loosely into the tool head before or after sliding the tool head into the top of the press. Also less adjustment needed by doing it this way. Then simply drop in powder funnel, attach powder measure and raise the ram with a case in for final adjustments. One more thing is to do all the final lock downs of dies with cases in all stages of shell plate and ram raised which provides best alignment fore consistency and helps with concentricity.
+1
Hey thanks for the great explanation on how the powder charge is set. I just got my first press, the XL650 and that was the only part I wasn't clear on. Until now. Glad you took the time to show making the adjustments, how many times to run it, etc. and not edit out or fast forward. Nice tutorial
mylink2u7 you’re welcome! Glad it helped you out. If you have any other questions please let us know.
Thank you for an awesome demonstration of how to setup the powder measure. I was having trouble getting this station to setup but with your explanation I think I have a better understanding of what to do!
You are welcome. I’m glad if was helpful to you.
Great explanation and tutorial. I've got a 30 year old Dillon Progressive press and the technology as changed but not the basic operation and concept. This helps me out a lot.
Thank you! Glad it was helpful to you.
Great video. I ordered my 550C from Dillon on 12/3/23 and am awaiting its arrival. I'm 72 and started reloading back in 1974. Up until now, I've used the red Hornady presses. My brother-in-law has a 550B and it reloaded, for me, much easier than my red machines - I really likes the Dillon powder measure. I'm looking forward to getting it. I'm not sure reloading saves me any money compared to buying new ammo, but reloading is very therapeutic, and fun. Plus, i can reload, things like my 44 Mag and 45-70 to a much gentler load, less recoil.
They are great machines. If I didn’t own and operate a manufacturing facility I’d probably find enjoyment out of it as well. Lost that joy years ago. lol. I’m honestly a bigger fan of the Hornady/lyman/mark 7 style powder measure. For a hobbiest it is probably fine but we have had a lot of wear issues and went away from them. In most cases it’s just a fun expensive hobby. Enjoy! Thanks for the comment.
Well, my 550C arrived. Setting it up was no problem, with the Dillon color instructions. I really like Dillon's case activated powder measure. Today, I loaded some 115 gr Hornady hollow points and it went smoothly. When I was setting up my powder measure, I took a empty, resized, 9mm case and inserted a primer, the right way, into the case. I was loading a type of powder called Titegroup. Without the primer, that powder would spill out of the primer hole in the case. I know you can use the end of Dillon's wrench to adjust the powder measurs control, but found the a ratcheting 7/16 wrench worked even better.
Great video brother... This was the hardest part to me when I first got my Dillon 550C mainly because only thing I ever used was a single stage and turret press before this... I'm still trying to learn everything about it but for handgun it's so much faster then anything I ever used before... Again great video brother!!!
You are welcome. Thank you for the feedback.
Another great tutorial, thanks!
Hey thanks for the video. Clear explanation helped me work out a problem I was having with mine. Great job!
Your welcome. Glad it was able to help you.
I'd been contemplating on getting a Dillon and this part has been confusing until now. Thanks for explaining it thoroughly and I think I have the confidence now to get this part set up correctly. Very nicely done.
Outstanding video! I just purchases my Dillon 550C and had no idea what I was doing. Your video cleared things up! Thanks, James
Awesome...glad to hear it. Let us know if you have any other questions.
rather than chase an exact weight one at a time I use in 9 m/m a .357 mag case throw three or four charges and weigh for the average .
Unless you are shooting 50 yard bullseye this will save a lot of time and have charges that are plus or minus 0.1 grain variation.
For .45ACP I use a cut down .30 '06 case.
The video is excellent and helped me a lot. I do think the case was flared a bit too much too but I think it was excellent.
Just getting back into reloading, this is a great tutorial. Your camera work is excellent. I was able to see how much flare is needed. Also you comments, especially the warnings about double load and how to measure will lead to happy days on the range. Thank you.
Thank you! Glad you enjoyed it.
thx bro, this solved my issue on my rl 1100
Your welcome. Glad it helped!
I use a small glass jar to run 10 loads which gives one more digit of precision
Thank you, very helpful
MPGunther1 your welcome. Glad it helped.
Awesome! Thanks to share your setup
Your welcome. Hope it helped!
I used your flied primer idea..thank you.
You are welcome! Glad it was helpful.
Very helpful thanks for the info. On powder measure going from lee torrent press to 650 thanks for powder measure info very good a few helpful do more on 650 thanks tommy
That is WAY too much flare. Your cases wont last more than 2-3 reloads at that rate.
This
Plus, I don't think he'd sized the case first which means it's actually worse.. yikes
There is no left or right to a round screw. Its either clockwise or counterclockwise. Using left or right with no reference could be either direction (relative to top or bottom of a screw)
Have you checked your case mouth flaring after tightened the powder measure clamp? Because it’ll open up the flaring more after tightening that clamp.
Is that a Dillon funnel orman after market? Looks like a cone shape.
I “think” it’s Dillon one. I didn’t buy it but I also know that at least at one point mr bullet feeders came with a funnel as well and it is possible that is where that one is from as well.
Thank you sir
Kyle Martin you are welcome!
I still have to set up my Dillon but the one question I have as I did not open my die set for 9mm is does the powder funnel come with the die set or do I need to buy that separately? Thank You for your answer in advance!
No, the powder funnel does not come with your die set. It will come with the conversion kit for whatever machine you are using. If you bought your machine new it would include the conversion kit for whatever caliber your loading. If you bought the machine used it may not have included the conversion kit. If you do end up needing one you can find them at www.extremereloadingnv.com/product-category/dillon-precision/dillon-conversion-kits/550-conversion-kits/
. Please let us know if you have any further questions. We can also be reached at sales@extremereloadingnv.com
you will buy the powder funnel with a conversion kit for the caliber you want to reload. You can also purchase separately, specific for the caliber. Buying it separately will likely be a special order as I've not found anyone who stocks the powder funnel or the shell plates individually.
Do you use return spring(s) on your powder bar?
I tried the spring and it certainly makes the machine run smoother. However, the spring is no guarantee the bell crank mechanism will return to the necessary position. I’ve loaded a couple of potential squibs on my XL650 when the spring did not do its job. Luckily, those rounds got caught by the powder check die. I strongly recommend sticking with the fail safe rod especially so on the 550 since you don’t have an available station for a powder check die on that machine.
Very disappointing you failed to mention that for a couple of dollars you can install a rotary thumb dial to increase/decrease the amount of the powder charge. The OEM nut provided by Dillon requiring the use of a wrench to make minute adjustments is ridiculously cumbersome. Additionally, good practice is once you think you have it set to the target weight, drop 10 charges and weigh the total amount of all 10. Then, divide the total weight by 10 to give you the average weight of each charge so you have a much better idea of how consistent your settings are.
Thank you for all your negative feedback and how things “should” be done in your opinion. This video was made over 7 years ago and was made to be a walk along video as setting up the machine. This has nothing to do with optional add ons that may or may not be available at the making of this video. Furthermore, depending on powders this powder drop should get you within 1/10th of a grain on most powders which is plenty accurate. If you are needing/wanting something more accurate than you shouldn’t be using a progressive style powder drop to begin with which is outside the training of this video.
@@ExtremeReloading so much potential in your video just wasted. Drop the wrench, get a knob and grow thicker skin.
Will do. Thanks for the advice.
How would you get sub 3gr?
You need to get Dillon's Extra Small Powder Bar, which is used for small loads like 32 S&W Long, e.g.
The case you used to set the flare - did you resize it first?
Brian Sweeney yes, these cases are already fully processed and ready to load.
Great video thank you. I’m getting a 650 and wondering what digital scale to get? They all seem crappy unless you spend a ton of money. Which one do you have/recommend. Thanks!
J S I have tried one that Berry’s Bullets makes and have had great luck with it. It was also less expensive than the Dillon. While I have not personally tried the Dillon scale everything they make is good and so while it is a bit more I would not hesitate to spend the money on that one either. I have tried the small mtm scales and overall I was not as pleased with them as the larger more expensive scales. Please feel free to contact me with any other questions and I’d be happy to answer them for you. 1-888-702-2341
I know this comment is 4yrs old . anyway I use a rcbs chargemaster for match loads . the scale itself is brilliant up one tenth of one grain
Are you serious ? You say you could run (load) 5 to 10 thousand rounds before checking the weight of the actual powder being thrown. I check (verify) the powder weight thrown every 100 rounds sometimes less. Just my 2 cents worth, Sorry
Yes I am serious. Notice the word could. My point was if your using a ball or flake powder the Drop is very consistent. I have used the same powder long enough to know what to expect when I’m loading. Everyone loads at their own comfort level and as a general rule I do tell people to check them much more often.
Tis video would be useful if you showed the screw you were adjusting instead of hoping we have the correct one. Thumb down.
There’s only one screw on the back to adjust plus or minus!
And if you have the same machine, you already know the screw to adjust and if you don’t have that knowledge, then you shouldn’t be reloading .