Hello from San Antonio, TEXAS! Depending I guess on the application as to how much force this gear is taking I would have pressed/heated it in using an interference fit followed up by a nice roll pin but that is me.
I really respect the way you work to design damaged items to be rebuilt. I'm a mechanic who finds it difficult to find pineapple-shaped gear and has a difficult structure
Well this is a turn up for the books. Keith Rucker has a go at cutting helical gears, having to make up some elaborate set ups, and takes for ages. Never mind the hours and hours spent reading up on it in the machinists handbook and others, and all the calcs to get the job done. Abom79 wouldn't even go there, too many calcs and trig for him, lol. Whereas these guys have the right machine for the job and get it done in no time.
Ele deixou a engrenagem folgada no eixo ❗, e posteriormente soldado com solda amarela ❗, condeno esse trabalho , a engrenagem deveria ser argolada a quente , e a solda com o eletrodo 7018.
Cast iron bar? I think not. But, far better work than most of these backwater machine videos. At least I saw actual measuring tools and proper wrenches.
Te pasaste de la medida , el piñón está flojo. Te pasa por trabajar alocadamente, sin micrómetros. Mejor era con chaveta en el eje y piñón y el ajuste de prensa.
Im a time served Fitter/Turner and this is most definitely not the proper way to do this in so many ways. Definitely scrap heap challenge engineering at it's best LOL
Já caiu um cavaco no meu olho, e eu usava óculos de proteção, até hj depois depois de 38 anos como torneiro mecânico não sei pq esse pessoal Não Usa óculos
Yup but it looked impressive. I give it one week in production before that glue breaks loose and the gear spins. Or maybe because it's soft steel she may just shear off the teeth on its first run
Hello from San Antonio, TEXAS! Depending I guess on the application as to how much force this gear is taking I would have pressed/heated it in using an interference fit followed up by a nice roll pin but that is me.
I really respect the way you work to design damaged items to be rebuilt. I'm a mechanic who finds it difficult to find pineapple-shaped gear and has a difficult structure
These guy's are fabulous fabricators
Yes.
Alex.
@@alex79teramo49no by
Well this is a turn up for the books. Keith Rucker has a go at cutting helical gears, having to make up some elaborate set ups, and takes for ages. Never mind the hours and hours spent reading up on it in the machinists handbook and others, and all the calcs to get the job done. Abom79 wouldn't even go there, too many calcs and trig for him, lol. Whereas these guys have the right machine for the job and get it done in no time.
Amazing to watch excellent work it's good to see how parts use to be made much respect.
Good Job 👍
Undoubtedly, master machinist. Thanks
Excelente maquinista , aprendo mucho
Meu sonho é comprar um torno 😃😃😃😃😃😃
Похоже, парнишка, уже один глаз повредил. Но всё равно работает без очков
Good job
Já trabalhei numa retificar 😃😃😃😃👍
Ele deixou a engrenagem folgada no eixo ❗, e posteriormente soldado com solda amarela ❗, condeno esse trabalho , a engrenagem deveria ser argolada a quente , e a solda com o eletrodo 7018.
Brazed instead of welded. No oil quench, no heat treat. Sounds like it's made to fail.
@@woodsonpayne8378 Thanks for watching 🙌
Très beau travail . .
Creative video, thanks :)
Good job 🇿🇦
You guys are very talented, good luck
nice eye precission setup on the lathe ;-)
what is the Helix Angle for this helical gear?
Prindapan pancen expert... 👍👍👍
Excelente trabajo
eye protection?
Não aceita erros se errar perde toda engrenagem aí que falo da trabalho pra fazer aí e puxar o escorpião pelo pé e caro. Trabalho top exelemte
por que não fez chaveta?
Cast iron bar? I think not. But, far better work than most of these backwater machine videos. At least I saw actual measuring tools and proper wrenches.
You'd be amazed at how much shops like this make for western countries. You can get relatively decent parts for very cheap.
Aaaaaa.@@okgroomer1966
Te pasaste de la medida , el piñón está flojo.
Te pasa por trabajar alocadamente, sin micrómetros.
Mejor era con chaveta en el eje y piñón y el ajuste de prensa.
It's good to let the swaffs fall out of the work piece if it's long swaffs can get tangled to the arm or around your neck u know it's always sharp
good tell 23:57
😊😊
Nice job, nice photography, try a bit if slow motion photography.
N. E. U. S. A.
Quincy, Massachusetts
Eu só torneiro mecânico a 34.anos sempre usei ipis segurança em primeiro lugar
It should have been preseed on and brazed after that
Beleza muito legal 👍👍
I like to see the tidy shops. Working in filth doesn't give people confidence in your work. These guys put the effort in.
❤
👍👍👏👏
Kitna time lagta hai isko banane mein?
Dwaring milengi?
Geeeeez >> He could have Thrown that Helical Gear onto that shaft from 20 feet away ..and it still would have gone on side ways !
No pues el que sabe sabe...muchos que se dicen torneros....no saben ni usar un Vernier pero pa cobrar que tal....y más aquí en la alcaldía de Tláhuac
В этом адском конвеере я упустил из вида термиста. 😄
Не упустил, его нет))
А зачем нам кузнец ? Не , кузнец нам не нужен . Когда чел протачивал шестерню на синем валу видно было что она не калёная .
Im a time served Fitter/Turner and this is most definitely not the proper way to do this in so many ways. Definitely scrap heap challenge engineering at it's best LOL
Já caiu um cavaco no meu olho, e eu usava óculos de proteção, até hj depois depois de 38 anos como torneiro mecânico não sei pq esse pessoal Não Usa óculos
به تراشکار بگو با اعتماد به نفس کامل کار مردم رو خراب کرد. 😂😂❤❤ درود
مصنوع من مادة A 60 خاطئ المادة غير صلبة
don't no what it's for but nice jub 😎👍
He eyeballed the runout to 0.02 mm.
No press fit, no heat treat, and BRASS brazing!?!?!?!?!?!
Te pasaste con el torno 😅
Hello j nanga innum speeda seivom
Muito folga entre a engrenagem e o eixo
Nota 0
Vai fica exentrica a engrenagem do eixo
Após a soldagem
Old USA when they made parts in the states, now we have to wait months.
You can still buy United States made parts, you just have to pay United States labor.
Не один резец не возьмёт хорошую шестяренку а такая сыромятина и ходит не долго
M Karachi se
Sir 🙏
New technology?
好粗糙的加工
Надо закалку сделать шестеренки
Bhai pement kitna hai tume
Queer looking cast iron. Thought machining swarf broke up, not coming off in spirals.
Thanks for watching 🙌
I won silensar maruti car 800 5 speed brother halp me.
it is not cast iron
An old pair of calipers and a can do attitude.
Nos profissionais tem que respeita a máquina porque a maquinas não respeita ninguém
Ok
That was wrong in so many ways
Yup but it looked impressive.
I give it one week in production before that glue breaks loose and the gear spins. Or maybe because it's soft steel she may just shear off the teeth on its first run
I see you are amateur machinist.. Good luck.
ini baru bubut....
@@RIBUTHERMANTO-v7mlp
笑死人
Это запчасти для хаймерсов или челенжеров?
Припой хоть на мм протёк?
Я боялся что бы его футболку не наматало на станок вместе с ним 😂
Когда напильником фаски снимал.