Stihl MS 462 C-M Review
HTML-код
- Опубликовано: 1 окт 2024
- Stihl MS 462 C-M Review Watch Before You Buy please feel free to comment below if i missed anything east coast guy with west coast bar lol
Email Katyhillfarmer@gmail.com please feel free to contact me
Facebook / katyhillfarmer
Instagram / katyhillfarmer
Twitter / katyhillfarmer
Want To Buy Items We Use On The Farm Check Them Out Here
www.amazon.com...
amzn.to/2MtYLs6 Try Amazon Prime 30-Day Free Trial
amzn.to/2rm1Zq2 GoPro HERO7 Black Camera What I use
amzn.to/2PUkr2A GoPro Dual Battery Charger + Battery
amzn.to/39a1v7K Create Amazon Business Account
Checkout my other videos here / katyhillfarmer
Subscribe For More great Videos goo.gl/ZRyyNd
Check Out My Channel / katyhillfarmer
About Me Well not much to say i work full time and also have a small registered angus farm in the hills of WV i also belong to the local vol Fire department and hold the rank as captain please feel free to ask any question you might have 
Развлечения
Thanks buddy...got one of these on the farm today....gonna have a blast with it!
Thanks for stopping by and it is a beast of a saw for sure hope you enjoy yours like I have mine
Did you drive the oil restrictor pin down when you turned your oiler up... as shipped the oil flow is limited to about half capacity. For a 32" bar there is a pin that needs to be driven down before you can max the high flow oil pump out
No I just turned the screw up
What are the lines for? Hahaha just bought one, haven’t use it yet but I am exited! Thanks for the video man. God bless!
Edwin Chire C. To show you the direction of the tree your cutting and where it should go
Stihls bar recommendations are extremely conservative. They even recommend a 25" bar for the 661cm. But they say on the website this saw will run up to a 36" bar
i run my 32 almost alll the time
FYI There's a little bump on the edge of the fuel cap [on the tank itself]: That bump is there to let you release pressure from the tank before pulling the cap all the way out. Stihl recommends you open the cap slowly to prevent fuel spray. Good to do if you put the saw away hot and open the tank cold later.
Zachary Bennett okay I will have to look thanks for the information and for watching the video
Those lines are ‘felling’ sights. The vertical line is used to set the notch cut for the direction you want the tree to fall. The horizontal line, the one inline with the bar, gives you an indication of where the bar is when it’s deep in the wood and you can’t see it during your back cut.
thank you for the information this is what i love about my channel people helping people again thanks hope you sub to the channel
The simplest and most precise description of felling sights I have seen yet
There's a pin you need to punch in by the oiler adjustment screw to let you open the oiler all the way. You'll need that if you're running a 32inch bar... alot of times they don't recommend a bigger size bar due to the oiler not being able to oil a bar that long its not the power.
thanks mine leaks now since being open all the way
@@Katyhillfarmer too much is not a bad thing.
If anyone has difficulty getting the wrap handle for this saw it uses the handle that is stock on the 462cm-R it has a scrench holder can in situ but can be removed with a sharp knife.
Thanks for the info and taking the time to let us know. have a great day hope to see you around
@@Katyhillfarmer no worries I had difficulty acquiring the wrap handle but as they updated the rescue saw which requires a wrap handle I jumped on it also to my knowledge it is the only wrap handle with the scrench holder it is a little cumbersome but I have not removed it thus far quite a useful addition. I normally like to put bright coloured duct tape on the shank of my screnches so I do not lose them but this won’t work on the handle as it has a tight fit.
They recommend up to 28"
it handles the 32 very well
@@Katyhillfarmer that's good to know hut I bet it doesn't balance on the saw like a 28" light bar does
Felling lines
thanks for the correction
Felling sights
Wisconsin edge thank you
Why did I need to watch before I bought?
Will Knott just showing some tips and tricks man thanks for watching hope you enjoy your saw
Great information, especially if one is shopping for a great 70cc class saw. Good job, young man.
Technical Terms lol. Love sthil haven’t pull trigger on pro saw yet. Got 310
Daryl Davis that’s what I started with and loved that saw got a good trade in on it thanks for watching