Thank you so much for this video!! I was attempting to swap.out my OEM headlights for LED by just going through the back and was so frustrated! I've learned so much from watching your channel!!
The other half and I installed my lights without removing the whole housing. It was a nightmare. He installed his this way and it was a world of difference! Thanks for sharing this.
I change out the headlights on both Rykers the hard way. Right side was the worst. I can see it would have been easier to remove the housing. Thanks again the the great videos.
Just followed your instructions, thank you so much for the video. Much easier to follow than the Slingmod instructions, they need to request use of your video. Again, thank you. Also, I used a T-30 and it fit perfectly? Probably the assembler used a different torx? Thanks Beth, and Tina (videographer).
Just a quick recommendation to take note of the USB’s polarity when removing the USB’s two Fast-On connectors. A “+” is cast into the rear of the USB housing adjacent to the terminal. Mark the Fast-On terminal sheath with a “+” using a Magic Marker so you get it right when re-installing the glove box. The PO of my Sport got it wrong and the USB port was dead until I figured out what was wrong and corrected the error.
Hey Beth, I just purchased a '22 Ryker 600 ACE and installed the SlingMods reverse jockey shifter, which required removing the lower left side panel. Shifter went on great, but now I can't get the panel back on. Any tips/tricks would be so appreciated. Am getting zero help from the dealership.
Beth, my frunk cover has a bunch of scratches. I tried googleing how to remove just the cover and only saw your video. My question is, can you just remove the frunk cover. I saw at cheapcycle that I can order just the cover. Thank you in advance for answering my question.
Yes! There are 2 small screws that hold the frunk lid in place. Then it should just pop off. If you run into trouble PM on FB and I can walk you through it.
What are you do with the plastic washer that was on the original headlight do you leave that off and just use the black one that comes with that headlight?
@Ryker Rydes thank you very much for your response it was definitely helpful. My next question is my Ryker is pretty new I almost hit 300 miles but I was told once I hit 200 miles I should get an oil change but when I called the dealer he's talking about its going to cost me a little over $400 is that true? For checking all the bearings and make sure everything is running correctly?
@@bullsback23 you should be able to bring your Ryker to the dealership for a free walk-through after 200 miles to make sure everything is intact. That is common place to do after you buy a new Ryker. As far as the oil change is concerned, there are two schools of thought. One is after the break in, which is usually 500 miles or some believe you can wait 6000 miles for the first oil change. I think I did mine after 4000 miles. I will give you the link so you can follow my steps to do the oil change and it’s not that hard, it’ll save you a bunch of money. How and When to Change Your Can Am Ryker's Oil (6 easy steps) ruclips.net/video/bOg6frl9XSs/видео.html
@@RykerRydes I wanted to try to do my first oil change myself but I didn't have the necessary equipment. I've seen videos and as expected most people doing oil change have everything they need but they don't really go through what you should purchase to continuously do your own oil change besides the filter and oil
Beth of all the parts & accessories; why haven’t can am or you considered adding hazard flashing lights? As a retired fl law officer I’m thinking about traffic safety and tons of traveling motorists. I’m curious why can am haven’t added these much needed lights to their US Rykers even in ‘22. Even you haven’t added it to your Ryker
You are 💯 correct. It should Be on the Ryker. Honestly, this may sound silly, but the one time I need hazard lights, I just put it in reverse. Boom, flashing lights. Not a perfect solution, but it works.
@@RykerRydes Use of hazard flashers: just verifying soooo when I take the trike out of park, while in reverse, the flashers illuminates and the trike will not move backward unless I throttle correct?
G'day Beth, greetings from down-under and kudos for the content you continue to supply - it's always informative. Regarding the Ryker "push-pins" do you happen to know the specifications for these and are all the push-pins on a Ryker the same size??
It made me want to cuss out the Slingmods guy that does the video on LED headlight installation. Tha parts in the damn video were not even the same !!!
Just want to add: a CAUTION, it’s so easy to break the plastic on the CanAm panels! Be VERY CAREFUL , if you are not sure as to how a panel removes. Go to you-tube, and do full research on how to remove a given panel. These things are made really CHEAP, I’m certainly sorry to say this cause I own one. Also when you break one of these tabs, good luck finding any type of glue that will bond to this type of plastic. And who wants to buy a new panel just because you broke one of the fasting tabs.😡
Thank you so much for this video!! I was attempting to swap.out my OEM headlights for LED by just going through the back and was so frustrated! I've learned so much from watching your channel!!
You are so very welcome! 🤗
You always make things so easy for your followers. What originally might have been to intimidating, you now make simple. Well done.
Thanks John!!!
The other half and I installed my lights without removing the whole housing. It was a nightmare. He installed his this way and it was a world of difference! Thanks for sharing this.
Awww thanks Heather!!! ❤️❤️❤️
Good review, good analytical skills. I like the way you divided the project into five small steps.
I appreciate that!!
I change out the headlights on both Rykers the hard way. Right side was the worst. I can see it would have been easier to remove the housing. Thanks again the the great videos.
Yup, 💯 easier. I miss you. We need a good chat soon!
Can not find your video for removing gas stains ! Thanks for all your help👍👍👍👍
Sorry for late response!!
What is the Best Way to Remove Gas / Petrol Stains (on a Can Am Ryker)?
ruclips.net/video/mplbQeWKy5I/видео.html
Just followed your instructions, thank you so much for the video. Much easier to follow than the Slingmod instructions, they need to request use of your video. Again, thank you. Also, I used a T-30 and it fit perfectly? Probably the assembler used a different torx? Thanks Beth, and Tina (videographer).
You're so welcome! I really appreciate your kind words!!!
Just a quick recommendation to take note of the USB’s polarity when removing the USB’s two Fast-On connectors. A “+” is cast into the rear of the USB housing adjacent to the terminal. Mark the Fast-On terminal sheath with a “+” using a Magic Marker so you get it right when re-installing the glove box. The PO of my Sport got it wrong and the USB port was dead until I figured out what was wrong and corrected the error.
Thanks for the tip! On my 2019, it doesn’t matter the which direction the USB is reattached. Interesting
@@RykerRydes Probably a different parts vendor through their supply chain.
👍🏻. This looked a whole lot easier than when you did it previously.
💯 easier!! I like to learn from my experiences and then share them. Thanks for your continued support!! ❤️
Yet another great tutorial video. I’m learning so much from your videos. You rock 🤙🏻. Thanks!!
Awwww thank you so much. I appreciate you watching!
Ps sorry for my delayed response, I am still on my bike trip.
Hey Beth, I just purchased a '22 Ryker 600 ACE and installed the SlingMods reverse jockey shifter, which required removing the lower left side panel. Shifter went on great, but now I can't get the panel back on. Any tips/tricks would be so appreciated. Am getting zero help from the dealership.
Hi Sharon. I am so sorry for the late reply. Were you able to get the panel back on?
Beth, my frunk cover has a bunch of scratches. I tried googleing how to remove just the cover and only saw your video. My question is, can you just remove the frunk cover. I saw at cheapcycle that I can order just the cover. Thank you in advance for answering my question.
Yes! There are 2 small screws that hold the frunk lid in place. Then it should just pop off. If you run into trouble PM on FB and I can walk you through it.
@@RykerRydes You're the best!! I mean that. I only think of your channel when I have Ryker questions. You're awesome!!!!
What are you do with the plastic washer that was on the original headlight do you leave that off and just use the black one that comes with that headlight?
You use the new one that comes on the new light.
@Ryker Rydes thank you very much for your response it was definitely helpful. My next question is my Ryker is pretty new I almost hit 300 miles but I was told once I hit 200 miles I should get an oil change but when I called the dealer he's talking about its going to cost me a little over $400 is that true? For checking all the bearings and make sure everything is running correctly?
@@bullsback23 you should be able to bring your Ryker to the dealership for a free walk-through after 200 miles to make sure everything is intact. That is common place to do after you buy a new Ryker. As far as the oil change is concerned, there are two schools of thought. One is after the break in, which is usually 500 miles or some believe you can wait 6000 miles for the first oil change. I think I did mine after 4000 miles. I will give you the link so you can follow my steps to do the oil change and it’s not that hard, it’ll save you a bunch of money.
How and When to Change Your Can Am Ryker's Oil (6 easy steps)
ruclips.net/video/bOg6frl9XSs/видео.html
@@RykerRydes thank you so very much
@@RykerRydes I wanted to try to do my first oil change myself but I didn't have the necessary equipment. I've seen videos and as expected most people doing oil change have everything they need but they don't really go through what you should purchase to continuously do your own oil change besides the filter and oil
Beth of all the parts & accessories; why haven’t can am or you considered adding hazard flashing lights? As a retired fl law officer I’m thinking about traffic safety and tons of traveling motorists. I’m curious why can am haven’t added these much needed lights to their US Rykers even in ‘22.
Even you haven’t added it to your Ryker
You are 💯 correct. It should Be on the Ryker. Honestly, this may sound silly, but the one time I need hazard lights, I just put it in reverse. Boom, flashing lights. Not a perfect solution, but it works.
@@RykerRydes Use of hazard flashers: just verifying soooo when I take the trike out of park, while in reverse, the flashers illuminates and the trike will not move backward unless I throttle correct?
Thank you!
G'day Beth, greetings from down-under and kudos for the content you continue to supply - it's always informative. Regarding the Ryker "push-pins" do you happen to know the specifications for these and are all the push-pins on a Ryker the same size??
All the pushpins on the Ryker are the exact same size. Here is a link for you: www.slingmods.com/replacement-push-pins
Thanks so much for watching!
Where can I find the led light?
Which red light?
@@RykerRydes the headlights the white one? I was to switch to the LED lights
Thank you for a nice vid tut.
Thanks Kenny!!! 😉
THANK YOU.
APPRECIATED Very much.
My absolute pleasure Terry. Thanks for watching!!
👍
Hi there just wanted to say hi,fred.
Hi Fred!!! How are you my friend??
First again.😄
You’re the best John!!
It made me want to cuss out the Slingmods guy that does the video on LED headlight installation. Tha parts in the damn video were not even the same !!!
lol!!! Thanks for the laugh. I try to be very thorough in my videos!
@@RykerRydes can wait to meet you in person, my wife thinks you’re awesome.
Hey, just saw your comment. Thanks for the love!!!
Just want to add: a CAUTION, it’s so easy to break the plastic on the CanAm panels! Be VERY CAREFUL , if you are not sure as to how a panel removes. Go to you-tube, and do full research on how to remove a given panel. These things are made really CHEAP, I’m certainly sorry to say this cause I own one. Also when you break one of these tabs, good luck finding any type of glue that will bond to this type of plastic. And who wants to buy a new panel just because you broke one of the fasting tabs.😡
I am so sorry to hear that.
Hi Beth, I hope you are well, G'Day, from down under.
Hello there! I’m doing great! We both are starting our riding seasons. Enjoy and be safe!