I will add that to the next video. Thanks for the suggestion. In the meantime you can see my other video on the Tesla model three, at the end I do show up close.
Do you know what custom length film is needed for the hood and the front bumper? I’m thinking about 5 feet length and 6-7 inches width for the front bumper?
I can the rest of the car area measured as follows FenderS - 4 feet x 2 feet Door- 3 feet x 5 feet (4) Back fenders - 4 feet x 4 feet Back 5 feet x 6 feet Back license plate area 4 x 2 feet Side mirrors- 1.5 feet x feet 1.5 Back bumper - 10 feet x 4 feet
What does the steamer do exactly for it? Does it help it stick better? Also any recommendations on which type of squeegee to get? Thank you! Love your work!
The steamer helps the film stretch/flex. Especially when it’s colder out. Every installer has their preference on squeegees. I use various fusion squeegees depending on the section of car. Thanks for watching 🙏
I can't ever understand why people do these videos with no VoiceOver- all I can do is watch you do the job in high speed with no advice, no expertise, no tips - nothing. Waste of time.
What over the shoulder pouch do you use?
It’s actually made to go around the waist but I just wear it over the shoulder. I got it from my 3M supplier
How much does it cost to have someone install this film for you?
Send me an email
Where r u located?
IE and Orange County areas. So cal
Can you give a quick explanation of what fluids to use during the install? There are two? Water with soap as first one? Second? And when to use?
First one is soapy water and the other just plain water with a little isopropyl alcohol.
What is the black spray tool? Just a power washer?
It’s a wagnor steamer.
@@dagraphics4369 what specific model is it?
Very good job!! But I wonder where did you buy this films? Amazon or eBay?
I buy directly from Xpel and STEK
How did you put emblem back on? have a new one on hand? or re-adhesive that one
Re-adhesive
Nice! What steamer is that?
Can you do a walk around on the finished work?
I will add that to the next video. Thanks for the suggestion. In the meantime you can see my other video on the Tesla model three, at the end I do show up close.
@@dagraphics4369 awesome, thanks!.
Do you know what custom length film is needed for the hood and the front bumper? I’m thinking about 5 feet length and 6-7 inches width for the front bumper?
4’x5’ for the hood
10’x30” for the bumper
@@dagraphics4369 awesome. Thanks so much!!
I can the rest of the car area measured as follows
FenderS - 4 feet x 2 feet
Door- 3 feet x 5 feet (4)
Back fenders - 4 feet x 4 feet
Back 5 feet x 6 feet
Back license plate area 4 x 2 feet
Side mirrors- 1.5 feet x feet 1.5
Back bumper - 10 feet x 4 feet
Did you use precut film or did you hand cut the film? The precuts seem to be much more expensive
How much? I have a model y on order
Send me an email. It’s in the description
Damn that black lip is smart.
Look at the Model X. That is were the idea came from I suppose.
your final touch with the black lip looks subtle but not to aggressive.. nice touch
Absolutely incredible job!
Thank you for sharing
What thickness of Xpel you put on the front bumper,... they do have two thicknesses correct ?
The black bottom looks aggressive!!!
I like the way you used that tape to realign the Tesla emblem after putting on the PPF. Very smart! :)
Great job. Thanks for sharing the video
Great Video. Did you put the Vinyl over the PPF?
Yes I did. The black was 3M satin black wrap vinyl.
I’m getting my model y tomorrow. Where are you located?
I service Orange County, CA area and surrounding areas too. My email is in the description if you’d like to schedule some work. Thanks for watching!
@@dagraphics4369 I sent you an email last night. I have a black model y
@@dagraphics4369 Do you service Riverside county, let me know, I need MY PPF, is there a number I can call you. BTW is there any warranty
@@00056433 Yes I do. Send me an email and we can set something up. It’s in the description
@@dagraphics4369 Is there a number where I can call you so I can setup a time
What does the steamer do exactly for it? Does it help it stick better? Also any recommendations on which type of squeegee to get? Thank you! Love your work!
The steamer helps the film stretch/flex. Especially when it’s colder out. Every installer has their preference on squeegees. I use various fusion squeegees depending on the section of car. Thanks for watching 🙏
Looks great! Awesome !
looks great!
I wish you were located in Texas.... just ordered my White Model Y and love your work and work Ethics!! how much that a work like that cost??
Thanks for the compliment!
Typically around $1000.
Thanks for watching!
Beautiful work! Yes, the black part looks so cool too! Do you plan to put ceramic or graphene coat on top of the clear & black films ?
I didn’t put any coatings on it. Customer just wanted PPF
I can't ever understand why people do these videos with no VoiceOver- all I can do is watch you do the job in high speed with no advice, no expertise, no tips - nothing. Waste of time.