Brother you need to tape down the sides on that body. That Protoform Corvette body is too thin on the sides and they always open up like wings. Speaking of wings maybe more rudder less elevator.
Thanks for the input! So the wing is the same one on Spartan that's been over 150 many times. I think it was just the heavy wind it was going up against. Suspension setup is the same as well. Usually never run in this crazy wind
@@InnovationRC I'd also go as far as to say that you may be getting a high pressure zone building up in the wheel well. And some Porsche like aerodynamic trickery may be needed. You may want to get a good leaf blower and a slowmo camera to setup an impromptu wind tunnel and see what is flexing and moving around to identify areas that need to be stabilized. Like just the shear power of the air going near 130-150 is absolutely insane.
I ran that Corvette body and he's right, tape those sides because they like to flap and I had to get the nose as close as I could to the ground so it wouldn't do backflips. Wasn't my favorite speed run body.
Awesome build man! It was so fast and the throttle output was only 46.5 therefore I think this car is promising! Good luck man! Here’s a quick tip, I think you need silicone tubing on the shaft of the shocks this prevents the car from going down the same level as the front end and do a backflip maybe try that instead of the toe links on the shocks to the other shocks! The contrast between Spartan and Vision is that Spartan is lighter and the motor and the equipment in the car pushing it down will not interfere the back to go down as well as vision having double the weight contrast to Spartan. In a nutshell, it’s either wind got under it and down or it got pushed down as those links will not take it that well contrast to silicone nitro tubings!
I noticed one of the main problems with these speedruns is the body always acts as a parachute, wonder if it'd be beneficial to add wheelarches and body posts on the side of the bodies? Great run either way, and a beautiful car at that!
I wouldn’t recommend locking out the suspension like you did you want there to have some to prevent the back shocks from going to far you can use Teflon tubing in the rear with stronger springs same with the front awesome video I’m excited to see more
@@InnovationRC Spring-rate is the measurement of how much force it takes to fully compress the spring. Calculate the down force that your wing produces at full speed, add approximately the weight of half of the vehicle(per quarter) and find/calibrate springs to match. From an engineering perspective it'd undoubtedly be beneficial to add some absorbency to such a rigid frame.
Glad to see you going after the 200 mph record. If anyone can do it it’s you. Build looks solid. I like your attention to detail. At those speeds aerodynamics plays as much a role as power. As shown by your crash. Possibly a bump or a stone allowed more air under the car and lifted the front end. Getting the batteries further forward for better weight distribution should help. Downforce helps but you sacrifice speed but you know that already. It’s a tricky trade off. Great job on the build.
Thank you! I appreciate that. It was super hot out that day so that's why the front tire chunked. Body never catches air it's setup correctly so air doesn't enter inside
Your dog is great. You should check out the active rear and front wing. . your spoilers will pitch up and down pensing on your throttle response. That mod would be the cherry on top of this build.
Wow, awesome bro!! Amazing build!!...I don't know how I missed the notification for this video, I have been waiting for this build ever since the 1st mention of this build lol. Glad that she had minimal damage, I know how it is to finish a build & then wreck the car because they're magically attracted to telephone poles that are 50FT apart!!😂😂 Keep'm Fast Bro!! 😎👍
Wicked build...glad to see another of your videos 📹. Vision has alot of hp..130's no problem...gonna check them batteries out.. Awesome work as usual 👏 👌
Just a really windy day. Funny to say it was a lucky crash with that little damage. When are you heading out there for another attempt? Would like to join you.
Kind of looks exactly like my build to the t! Except I’m using a scorched twin motor mount. Scorched all the way. That Bec is quite a good idea. Nice work
It's been awhile. Good to see you back at speed runs. With the front suspension locked out your front tires are taking all the bumps on the road and not the shocks. Will have to see what happens with no wind. I hope no tire chunking out at speed. Locked out suspension is going to be interesting at speed. Only time will tell. I hope all goes well, Great road for speed runs NO TRAFFIC AT ALL!!!!!!
Thanks, never had an issues with locked front suspension on Spartan I think the tires just didn't hold. I run the same tires in Spartan as well so it was probably just a hiccup.
I was looking at doing this for my limitless going with two hobbywing 1100kv motors I think it's a 1/5 size and two traxxas 8s vxl escs it's a bit pricey
Great videos! All of your RC vehicles are top notch!! On your motor wires what are you using to hold your wires together nice and neat? I have 10 gauge wires and it’s hard to find clips that are small that hold the wires together.
so straight and stable! brilliant builds. watching that slow mo clip, did the air get in behind front wheels and lift arches? looked like sides expanded due to no posts or tape on sides
@@InnovationRC dam foams spittin chunks... that's gotta be the biggest issue every speedrunner faces gettin foams that hold up well. all the best for next attempts 🤞
Front splitter must stick out from underneath the body and stick the body to the splitter with ductape. That with help keeping the nose down. Good luck dude!
I race RC cars too I have a fast one but not that fast you got a little bit more than me mine gets up and boogies I'll tell you that but not passage that
Just watched your video brilliant video mate lots of power. I've bought myself the rovan f5 electric is this any good for speed runs like 12s or 24s what's your views bud let me know 😀😉
Some great runs there! Defo gonna need some tape for the body though. Looks like air got under it, and that was game over, but luckily it survived! Can't wait to see it out again!
Much appreciated! Unfortunately the tire chunked out which made the whole front end lift. It's Spartans exact suspension setup, he never flipped. Tires needed a little more prep most likely but my hopes are still super high with them! Spartan never had an issues over 150+ Mph!
@@jordanritchie2198 what is type? Do you mean true? Generally foams you I just break them in properly, running a few times at 110-120 mph, then they should be ok for crazy speeds.
@@InnovationRCsorry🤦🏼♂️ tape the body to the chassis so air doesn't get in/under the body like razz does and James. The tape the body on the side to the chassis and the front to the splitter
A BEC isn't a small ESC- it is merely supplying a regulated voltage to the rx/servo/etc. Just want to clarify that. Most ESC's have a built-in BEC, but a dedicated BEC is unable to perform functions of an ESC as far as controlling the motor.
Man I feel your pain absolutely a beautiful build buddy be proud👍👍! I did the same thing with my dual 1721's first pass on 8s they are insane! It sucks but we learn from every crash
That's bananas on 6s. It looks like at the 9:50 mark a pieces of tire flew off into the grass as the car was about to pass by you. When that happened Newton's 3rd law came into effect pushing the car up into the air stream. I thought you were done building airplanes. lol. I hope to see her back out there soon!
On Instagram you can reach me @InnovationRC. For me to answer very deep questions about rc, you'd have to subscribe! If you do I get the messages like texts. I think it's only like $2 a month.
I've seen a lot of people cutting their rears out of the bodies, acts like a parachute? I dont know the effectiveness at that high of speed, but my heart sank seeing that go airborn, would hate too see that hard work get destroyed
![Jack Harlow - Hello Miss Johnson [Official Music Video]](http://i.ytimg.com/vi/Q86_nlRoIGw/mqdefault.jpg)
Check out Innovation RC Batteries here! Thanks for watching!
chinahobbyline.com/collections/innovation-rc-series?ref=LM9JnF68TkdSj4
Keep up the awesome job 👍🏽💯
@@MatrixRC thank you!
I’ve never seen anyone pull a trigger like this man it’s crazy how nice this guy drives
Brother you need to tape down the sides on that body. That Protoform Corvette body is too thin on the sides and they always open up like wings. Speaking of wings maybe more rudder less elevator.
Thanks for the input! So the wing is the same one on Spartan that's been over 150 many times. I think it was just the heavy wind it was going up against. Suspension setup is the same as well. Usually never run in this crazy wind
I agree with the body tape. Keep it all tight to the chassi
@@InnovationRC I'd also go as far as to say that you may be getting a high pressure zone building up in the wheel well. And some Porsche like aerodynamic trickery may be needed.
You may want to get a good leaf blower and a slowmo camera to setup an impromptu wind tunnel and see what is flexing and moving around to identify areas that need to be stabilized.
Like just the shear power of the air going near 130-150 is absolutely insane.
This to
I ran that Corvette body and he's right, tape those sides because they like to flap and I had to get the nose as close as I could to the ground so it wouldn't do backflips. Wasn't my favorite speed run body.
Scary when they take flight cool video
Such a beast of a car, my heart sank when it flipped. Keep it up and work out that aerodynamics. Watch out Raz and Kev LOL
Watch out Raz. LOL.
@@501speedcrew9 C'mon - there is nothing more to this speed running business than simply adding more power... ;)
@@DESOUSAB That why we are 1 of 3 to break the 200 MPH mark.
@@501speedcrew9 🤭👊
Before i finish watching…. The rear wing needs to go. Just fins.
Wow! That car has incredible potential! I’m very happy it wasn’t badly damaged!
Awesome build man! It was so fast and the throttle output was only 46.5 therefore I think this car is promising! Good luck man! Here’s a quick tip, I think you need silicone tubing on the shaft of the shocks this prevents the car from going down the same level as the front end and do a backflip maybe try that instead of the toe links on the shocks to the other shocks! The contrast between Spartan and Vision is that Spartan is lighter and the motor and the equipment in the car pushing it down will not interfere the back to go down as well as vision having double the weight contrast to Spartan. In a nutshell, it’s either wind got under it and down or it got pushed down as those links will not take it that well contrast to silicone nitro tubings!
I noticed one of the main problems with these speedruns is the body always acts as a parachute, wonder if it'd be beneficial to add wheelarches and body posts on the side of the bodies? Great run either way, and a beautiful car at that!
Nice first pass, wasn't expecting to see that happen in the second pass luckily it appears to be not to badly damaged.
I wouldn’t recommend locking out the suspension like you did you want there to have some to prevent the back shocks from going to far you can use Teflon tubing in the rear with stronger springs same with the front awesome video I’m excited to see more
At the speed it goes regarding rear downforce, it will still slightly squat
@@InnovationRC Spring-rate is the measurement of how much force it takes to fully compress the spring. Calculate the down force that your wing produces at full speed, add approximately the weight of half of the vehicle(per quarter) and find/calibrate springs to match. From an engineering perspective it'd undoubtedly be beneficial to add some absorbency to such a rigid frame.
I'm gonna agree and disagree here, if he's on super smooth ground......🤔
@@EZ-D-FIANTgood luck finding that. I've ran on airstrips and they weren't even perfectly smooth.
Glad to see you going after the 200 mph record. If anyone can do it it’s you. Build looks solid. I like your attention to detail. At those speeds aerodynamics plays as much a role as power. As shown by your crash. Possibly a bump or a stone allowed more air under the car and lifted the front end. Getting the batteries further forward for better weight distribution should help. Downforce helps but you sacrifice speed but you know that already. It’s a tricky trade off. Great job on the build.
Thank you! I appreciate that. It was super hot out that day so that's why the front tire chunked. Body never catches air it's setup correctly so air doesn't enter inside
Awesome again. You are one of few that truly tries and don’t give up.
Love your work my friend.
Great project 👍. I think the problem was the rear wing. Must be straight. This cause the flying issue. Keep up the good work 👏.
Your dog is great. You should check out the active rear and front wing. . your spoilers will pitch up and down pensing on your throttle response. That mod would be the cherry on top of this build.
Amazing builds as always, but i think you need to replace that wing with someting flat.
Wow, awesome bro!! Amazing build!!...I don't know how I missed the notification for this video, I have been waiting for this build ever since the 1st mention of this build lol. Glad that she had minimal damage, I know how it is to finish a build & then wreck the car because they're magically attracted to telephone poles that are 50FT apart!!😂😂
Keep'm Fast Bro!! 😎👍
Wicked build...glad to see another of your videos 📹. Vision has alot of hp..130's no problem...gonna check them batteries out.. Awesome work as usual 👏 👌
Crazy power. Scorched chassis are super strong. Raise punch to 100 haha. Should help
Lots of very interesting stuff in this video. Great job!
Just a really windy day. Funny to say it was a lucky crash with that little damage. When are you heading out there for another attempt? Would like to join you.
I saw at the start you used 8mm castle connectors on the esc and then changed to qs8 ?
Kind of looks exactly like my build to the t! Except I’m using a scorched twin motor mount. Scorched all the way. That Bec is quite a good idea. Nice work
awesome setup man. What is best supplier for the speed run foam wheels?
Welcome back!!! That was all wind to blame nice set up!!!
That suspension setup is genius!
Deff didn’t expect that especially after such a tight first run just glad it didn’t get mangled to bad bro!!
It's been awhile. Good to see you back at speed runs. With the front suspension locked out your front tires are taking all the bumps on the road and not the shocks. Will have to see what happens with no wind. I hope no tire chunking out at speed.
Locked out suspension is going to be interesting at speed. Only time will tell. I hope all goes well, Great road for speed runs NO TRAFFIC AT ALL!!!!!!
Thanks, never had an issues with locked front suspension on Spartan I think the tires just didn't hold. I run the same tires in Spartan as well so it was probably just a hiccup.
@@InnovationRC yea no more hiccups over 20mph🥴
Good thing arrma designs really fast and tough tanks.
Good to see you back doing videos 😉🤙👍🤝
Good to see you posting again. What a unit! Can't wait to see it rip 200.
Awesome to see local Delray in the videos. 🤙
crazy build dual motors and stunning to look at!!! upvoted!!!!!!!
That is Awesome 👊🏽💯. The power is wicked brother
Nice build bud don’t give up keeps us motivated
Great video Vision lives to see another day👊👊💯💯
I suggest a fpv unit on these high speed runs. That way it never gets out of field of view.
Awesome video can't wait to see more awesome run awesome job on invision looks awesome and stay safe
Real awesome build Brandon good luck with it. 🏁
Thank you sir much appreciated!
@@InnovationRC yes sir
Great video as always 👌🏻
Gutted about the car getting airborne though but thankfully not much damage
Man the body mount supports are badass👍
Awesome work big brother
I am glad for you that it did not do more damage
That was totally sick bro
Is it possible to add a good weight at front end. All these tests ends up on car flying. Well done mate.
Wow 🤩 insane bro. Glad the crash wasn’t too bad
Thats a really awesome build. 👌🏻👍🏻
That's fast bro I don't like when my car takes off flight but god will never put fear on his people u got it all together bro 🙂
It's certainly a scary thing... Thanks man! I appreciate it
I was looking at doing this for my limitless going with two hobbywing 1100kv motors I think it's a 1/5 size and two traxxas 8s vxl escs it's a bit pricey
Really really clean lookin build
Man I'm from Brazil I love your videos and it's great to see you back....I think you have a 200 mph car for sure. I can't wait for the next video.
I greatly appreciate that!
Are you in SE Florida? I think we’ve talked before. I’m doing a speed run build and it would be cool to link up. Thx
That's a 200+Mph car bruh. Heck of a job and creativity.
Awesome run bud 👍
Great to see you back man!
Thank you!
Yessir bro, beastmode status. Baby steps with this monster build, youll eventually get out of it what you were expecting and then some. 👊🏼👊🏼💯💯🔥🔥
Great videos! All of your RC vehicles are top notch!! On your motor wires what are you using to hold your wires together nice and neat? I have 10 gauge wires and it’s hard to find clips that are small that hold the wires together.
Thank you! They are just zip ties holding them together!
@@InnovationRC You’re welcome! Thanks !
so straight and stable! brilliant builds.
watching that slow mo clip, did the air get in behind front wheels and lift arches?
looked like sides expanded due to no posts or tape on sides
Tire chunked out in the front making the vehicle flip. Never had an issue with the Corvette body catching air.
@@InnovationRC dam foams spittin chunks... that's gotta be the biggest issue every speedrunner faces gettin foams that hold up well. all the best for next attempts 🤞
@@dodgymtbknee I have high hopes still with these foams I trust them. First hiccup I've ever had with these
Front splitter must stick out from underneath the body and stick the body to the splitter with ductape. That with help keeping the nose down. Good luck dude!
that car is moving nice to see the set up and process it to to get it going that fast
👍👍How was definitely fast and I was only half throttle like you were saying if you did a good job building that
I race RC cars too I have a fast one but not that fast you got a little bit more than me mine gets up and boogies I'll tell you that but not passage that
I love the car!, you can break the WR of 204mph, with you engineering skills on rcs
Lol
Beautiful Build Bro 👍👊
I’m mad you flipped it but it’s good nothing looks damaged but I wanted to see you complete that pass great job
Awesome build🔥🇫🇷
Few tapes might have helped keeping that beautiful car on the ground.
Awesome job 👏
I should not be watching this, spend enough on helicopters now. But these fast cars are just too kool to ignore.
Dope build
Just watched your video brilliant video mate lots of power.
I've bought myself the rovan f5 electric is this any good for speed runs like 12s or 24s what's your views bud let me know 😀😉
rover f5 electric car / mogg rc model
ruclips.net/video/3rSlUJqIKmU/видео.html
Thank you! Well I'd have to say anything over 12s is ridiculous in all reality. 12s is more than enough power to move anything!
Excellent build! Besides the wind, maybe the lack of front shocks may have contributed to the flight!
Everyone I watch uses those tires....always exploding,that bananas 🍌
It was too hot out I think that's why it chunked
Looks good!
VERY HYPE FOr the batteries buying a pair next Wednesday
Awesome! I'm hyped too!
Wow man, this sounds almost as fast as Raz’s twin motor speedrunner
But are you gonna get over 198 mph on a pancar set-up?
Don't see why not
Nice build, maybe just a different body and wing
What your remote can control up to 1km?
Nice brother I need a set of these brother!
Just an observation.. from video you had wind deflection off of your car and trunk disturbing the air in the road .. which made flight.. ? Maybe
Tire chunked out unfortunately. The wind never helped either though haha!
Imagine how dual 8s at full power will look like
Voltage vs amp at usage is a thing, sometimes for speed runs you can get more from less, American "bigger is better" isn't always correct......
Some great runs there! Defo gonna need some tape for the body though. Looks like air got under it, and that was game over, but luckily it survived! Can't wait to see it out again!
This right here.
Much appreciated! Unfortunately the tire chunked out which made the whole front end lift. It's Spartans exact suspension setup, he never flipped. Tires needed a little more prep most likely but my hopes are still super high with them! Spartan never had an issues over 150+ Mph!
@@InnovationRC don't think it would hurt anything from typing it? Been seeing all the big timers with type on there's. Reason why u don't want to type
@@jordanritchie2198 what is type? Do you mean true? Generally foams you I just break them in properly, running a few times at 110-120 mph, then they should be ok for crazy speeds.
@@InnovationRCsorry🤦🏼♂️ tape the body to the chassis so air doesn't get in/under the body like razz does and James. The tape the body on the side to the chassis and the front to the splitter
2k to go straight for a few seconds! I will pass lol. It's still freaking bad ass looking though for sure great job on the build
“HALF” throttle Sun¿ that ish CRAZY!!
Front splitter to long trim it down an inch try that mate
A BEC isn't a small ESC- it is merely supplying a regulated voltage to the rx/servo/etc. Just want to clarify that. Most ESC's have a built-in BEC, but a dedicated BEC is unable to perform functions of an ESC as far as controlling the motor.
I'd guess it hit something maybe..or the front splitter might stick out to far caught air
Nice 👍🏾
Man I feel your pain absolutely a beautiful build buddy be proud👍👍! I did the same thing with my dual 1721's first pass on 8s they are insane! It sucks but we learn from every crash
How fast did it go
@@user-sd7bh1hc8g 145mph then took flight and wiped out a speed controller xlx2😩 it was incredible
Should have kept the front shock springs in. The whole car was tuned for insanity. And it might need skate board wheels.
Great video 👍🏻🍻
Thank you Rob!
So Crazy and so much Money Kohle Zaster!!!
BIRTHDAY BOY GETS FIRST !!!
So great!!! Amazing!!
That's bananas on 6s. It looks like at the 9:50 mark a pieces of tire flew off into the grass as the car was about to pass by you. When that happened Newton's 3rd law came into effect pushing the car up into the air stream. I thought you were done building airplanes. lol. I hope to see her back out there soon!
I think the rain why is that the tire chunked out. Hard to tell with the wind though
Will these battiers fit good in my xrt or outcast 8s?
Great build. How can I reach you for information for my build
On Instagram you can reach me @InnovationRC. For me to answer very deep questions about rc, you'd have to subscribe! If you do I get the messages like texts. I think it's only like $2 a month.
Pleaseee use a fc100 that body cannot provide the downforce needed for high speeds and will left up a lot more then you relies
Dumb question but how does someone figure out HP on a RC?
Great build!!
Thank you! Wattage output converted to electrical HP
Are the battery really any better than the 9500 chinaline hobby 90c batteries?????
Yes they are a step above them
@@InnovationRC good to know bc my china line 70c g series 6s are better then my china line 90c 6s packs
Bro I would change the body I know the c8 is your thing but the fc100 body and Porsche is way better for those kind of speeds💯
Question how long did it took you to learn how to work with your RC?👍👍
I've seen a lot of people cutting their rears out of the bodies, acts like a parachute? I dont know the effectiveness at that high of speed, but my heart sank seeing that go airborn, would hate too see that hard work get destroyed
7:34 do u not use side tape for bodyshell?