Am schimbat plăcute la Octavia 4 și a mers perfect! E foarte bun video! Eu am mai rotit manual , in sensul acelor de ceasornic,de bolțul ce intra in motoraș.
Great video thanks for the help doing this job. One to watch for if your car has high mileage or lots of corrosion like mine. I managed to snap one of the bolts which holds the parking brake servo motor to the caliper. I suggest soaking from both sides with penetrant spray 1st before loosening.
Thanks for the info. I actually thought it was a "normal" torx, but now I can see it isn´t. I told my friend that I could change the brakes on his Passat if he wanted me to, however it means that I will have to purchase new tools 😞
Great video, this is going to help me a lot. Just an idea that would make it even better... would be good if at the start you could list all the tools and sizes required for the job.
I found out that the disc can be removed and remounted without unscrewing the calipermount! This makes a big difference since those bolts can get stuck hard!
I confirm that it is indeed easy to remove the disk without unmounting the calipermount! (at least on my Passat B8 110kW 2.0 TDI from 2016, Brake "1KU" or FNc-M42 (16"), 300mm disk). Also I'd recommend to use VCDS/OBDeleven/etc. to open the electric parking brake - this way it is not necessary to unmount the electric motor before pushing the brake piston back into the brake caliper. In summary I had just to - put the electric motor in service position (open) - remove the spring - unscrew both 7mm hexagon sockets screws to remove the brake caliper from the brake pads - unscrew the little Torx on the brake disk - push back the brake piston (for this I opened the compensation reservoir of the brake fluid) - mount everything back - close the electric motor
Followed this procedure today, thought it went great until I tried to drive the vehicle. Brakes all work fine and so does the electric handbrake but the car is displaying all faults with the braking system and is running rough and stalling. Any ideas what has gone wrong?
Am un passat ca si al tau , cand dau cu spatele si pun frana trosnește ceva la plăcuțele de frână, asta dupa ce am pus noi ( Bosch) înainte nu făcea, câteodată se aude foarte tare , sti cumva de ce ?
@@josuachannel5805 nu sunt mecanic, dar din câte știu înainte de a umbla la frână spate trebuie dezactivat din soft senzorul din electronica frânei de mână.
What is the 12 sides torx type tool for removing the brake caliper carrier. I hit this problem before where i did not have that tool to change disc. Whats the tool called?
so you will need 14. I don't know exactly what it's called, but if you want I can leave you a link with a kit and from there you can search for more details.
Hi,I tried to do the same today and I almost made it but I couldn't push the pistons all the way in and I couldn't push the pads.Does anyone know how to do it properly?Thank you
if you take off the electric motor that actuates the brake piston, you will not break anything, however I do not know if the brake piston is pushed by normal pressing or only pressing and turning at the same time. in my case as you saw in the video everything was normal and I used this method many times on different cars in the VAG group
Warning! Please do not Do it with out vcds did it same way 1 year ago and the hand brakes weren't really fully disingadged and the pads lasted only 7 months and my left handbrake doesn't engage fully.
probably has absolutely nothing to do with vcds, more likely there is another problem, like a rusted piston that gets stuck, chrome seems to be very thin on these, so once they start rusting from the dust cover groove, it goes quickly, in my case I serviced all 4 corners and everything was fine, pistons moved freely when I put the new discs and pads on, yearly inspection brake test was perfect, but after the winter I had first one seize in the front, lots of rust behind dust cover, then a month later one of the rear ones also, but that one "fixed" itself after few km when I actuated the hand brake a few times, when I took that one apart - same issue - heavy rust starting from the dust cover groove on the piston they use loads of salt on roads here in winter, and usually the weather is around 0 for most of the winter, so everything is rusting like crazy...
![Seungmin "그렇게, 천천히, 우리(As we are)" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/kAzmhLHePqU/mqdefault.jpg)
Great work! Only one remark, to replace rotor no need to dismount brake pads holder on rear wheels 😊 for b8 passat.
Hi, good remark and do not you know if is necessary to dismount brake's electric motor for pushing brake piston?
Am schimbat plăcute la Octavia 4 și a mers perfect! E foarte bun video! Eu am mai rotit manual , in sensul acelor de ceasornic,de bolțul ce intra in motoraș.
Salut. Foarte educativ si bine realizat. Succes in continuare.
Great video thanks for the help doing this job. One to watch for if your car has high mileage or lots of corrosion like mine. I managed to snap one of the bolts which holds the parking brake servo motor to the caliper. I suggest soaking from both sides with penetrant spray 1st before loosening.
for anyone like me searching, the 12 point torx looking thing is an m14 (14mm) triple spline, also named triple square or xzn tamper
Thanks for the info. I actually thought it was a "normal" torx, but now I can see it isn´t. I told my friend that I could change the brakes on his Passat if he wanted me to, however it means that I will have to purchase new tools 😞
Není zapotřebí sundavat drzak třmenu, kotouč jde vyměnit bez jeho demontáže
Super information even with no dialogue. Thank you.
Lucrare eleganta ,Felicitari !!!
Mulțumesc!
Great video, this is going to help me a lot. Just an idea that would make it even better... would be good if at the start you could list all the tools and sizes required for the job.
Very Good Instructional video on the B8 thank you.
It's a very nice video. Thank you very much.
Dude you are amazing such a great video helped me enormously on my Passat today
I found out that the disc can be removed and remounted without unscrewing the calipermount! This makes a big difference since those bolts can get stuck hard!
How?
On the same car, passat b8? If so thanks for the info 🤗
@@fractalofgod6324 just angle the disc and take it off
It‘s possible on the Passat and Tiguan don‘t know why Not on others
I confirm that it is indeed easy to remove the disk without unmounting the calipermount! (at least on my Passat B8 110kW 2.0 TDI from 2016, Brake "1KU" or FNc-M42 (16"), 300mm disk).
Also I'd recommend to use VCDS/OBDeleven/etc. to open the electric parking brake - this way it is not necessary to unmount the electric motor before pushing the brake piston back into the brake caliper.
In summary I had just to
- put the electric motor in service position (open)
- remove the spring
- unscrew both 7mm hexagon sockets screws to remove the brake caliper from the brake pads
- unscrew the little Torx on the brake disk
- push back the brake piston (for this I opened the compensation reservoir of the brake fluid)
- mount everything back
- close the electric motor
Same for golf mk8 ?
Spot on thank you.
Followed this procedure today, thought it went great until I tried to drive the vehicle. Brakes all work fine and so does the electric handbrake but the car is displaying all faults with the braking system and is running rough and stalling. Any ideas what has gone wrong?
Did You reconnect the ABS jumper?
super,thank you
labais
👍
Well mate , brilliant, what size is the torx bit to remove the caliper hanger/carrier 👍🏻
Can I get the song in an extened version?😆😉
Salut . Aș dori să te intreb ceva , cum putem lua legătura? Multumesc !
Spune-mi in comentarii daca se poate
Am un passat ca si al tau , cand dau cu spatele si pun frana trosnește ceva la plăcuțele de frână, asta dupa ce am pus noi ( Bosch) înainte nu făcea, câteodată se aude foarte tare , sti cumva de ce ?
@@josuachannel5805 nu sunt mecanic, dar din câte știu înainte de a umbla la frână spate trebuie dezactivat din soft senzorul din electronica frânei de mână.
What is the 12 sides torx type tool for removing the brake caliper carrier. I hit this problem before where i did not have that tool to change disc. Whats the tool called?
so you will need 14. I don't know exactly what it's called, but if you want I can leave you a link with a kit and from there you can search for more details.
@@auto.b.i.daniel yes please, thanks 👍
www.ebay.co.uk/itm/INDUSTRIAL-Impact-Spline-Bit-Sockets-Tamper-Proof-Spline-1-2-M4-M18-Hex-Torx-/363291189948?mkcid=16&mkevt=1&_trksid=p2349624.m46890.l49286&mkrid=710-127635-2958-0
I am looking for those center wheel dust covers für the B8. Anyone knows the VW part numbers for rear and front ??
3:38 what is that for?
Hi,I tried to do the same today and I almost made it but I couldn't push the pistons all the way in and I couldn't push the pads.Does anyone know how to do it properly?Thank you
Just turn the pin that is rotated by the motor in the right direction to retract the piston. If you push it without rotating it you can damage it.
Is it possible to perform this procedure without ‘opening’ the brake?
Se împacă discurile de la Brembo si plăcuțele de la Ate?😅
Sa știi că am fost mulțumit de frânare.
@@auto.b.i.daniel Eu am pus discuri Brembo perforate si frânarea e ca la formula 1😆
Salutare, poți să-mi spui te rog de cât este Torx-ul care tin cele doua suruburi de la suportul etrierului, cele 2 suruburi mari din spate?
Salut, scuze dar nu îmi amintesc exact dar pot să îți spun că este de 14 dar totuși să ai și unul de 12 în cazul în care nu îmi amintesc bine
14
Nu este cu cap torx ci cap spline, un fel de steluță de 12 muchii și este de mărimea 14.
fro cro braaaaavvvvvvooooo, and tanx
Hi, B8 rear disk 300mm right?
in my case 300mm. I have 2.0 150hp
@@auto.b.i.daniel Thanks, mine 2.0 220Hp R line.🙂
@@Dannyongwc5 Not sure if yours is 300mm
@@auto.b.i.daniel Same as your according to Brembo spec sheet.
Salut.Acelasi sistem este si la Tiguan?
Salut . Nu sunt sigur daca este la fel dar mai mult ca sigur este asemănător
Question, so it doesn't fuck up the electric brake system at all? And do you pump the brakes afterwards like normal?
if you take off the electric motor that actuates the brake piston, you will not break anything, however I do not know if the brake piston is pushed by normal pressing or only pressing and turning at the same time. in my case as you saw in the video everything was normal and I used this method many times on different cars in the VAG group
👏👏👏👏
Warning! Please do not Do it with out vcds did it same way 1 year ago and the hand brakes weren't really fully disingadged and the pads lasted only 7 months and my left handbrake doesn't engage fully.
probably has absolutely nothing to do with vcds, more likely there is another problem, like a rusted piston that gets stuck, chrome seems to be very thin on these, so once they start rusting from the dust cover groove, it goes quickly, in my case I serviced all 4 corners and everything was fine, pistons moved freely when I put the new discs and pads on, yearly inspection brake test was perfect, but after the winter I had first one seize in the front, lots of rust behind dust cover, then a month later one of the rear ones also, but that one "fixed" itself after few km when I actuated the hand brake a few times, when I took that one apart - same issue - heavy rust starting from the dust cover groove on the piston
they use loads of salt on roads here in winter, and usually the weather is around 0 for most of the winter, so everything is rusting like crazy...
A cheaper alternative is to have an obd11
Shame you didn’t show cleaning anything except the disc hub.
Vsechno spatne 🤦🤦🤦 kdyby si to udelal a povolil rucni brzdu pres vcsd tak je to jednoduchy 🤦🤦🤦
Die Musik ist ja voll nervig.🤮🤮🤮🤮
hi i have some brembo and ate ceramic :D.