I am using ACM for the top of a mobile model train n-scale 3x8 foot table. What thickness are you cutting? Do you think the thickness you cut in the video will work for me with 2020 extruded aluminum braces on all four sides and across the middle? Thanks for the advice.
I use 3mm (1/8" ) ACM most of the tie and in that video. Over the span of 8ft I would use 3 braces in the center (2,4,6ft) and all 4 sides. The 3mm is pretty flimsy, ACM will bend so the more support you can give it the better.
In the past bought it from whoever had what I needed when I needed it. Now I like to use the Piedmont Plastic Sign Grade ACM, I think it's the best out there from a quality and price standpoint.
why couldnt I have seen this about 6 hours ago. Just ordered a 2440mm x 1220mm (8 x 4) sheet and paid extra to get it cut into 4. WIll try this next time I order
I have a AccuCutter(.com) and use the Cornermate CM40A Table with a 3/4" rounder. A little pricey but works great, had it for 7 years and never an issue. I generally cut 1/8" ACM with ease but works fro coro and up to.040 aluminum too.
ACM stands for Aluminum Composite Material, it is probability one of the top 3 sign making substrates in the industry. ACM just about replaced normal aluminum panels (.030,.040,.060,.080) for making signs because it has so many uses and easy to cut, bend and route. There are a lot of different choices out there, I like to stay with a .015 or .020 aluminum skins in a 3mm total thickness. ACM is a general name but if you look up DiBond they pretty much "invented" the ACM about 20+ years ago but it's twice the cost.
If you treat this like drywall and cut one side fold and cut the other side it's way easier than trying to snap it. I'm actually not sure why you're doing that
I wish I could buy you a beer. This is the best video ever. Thanks so much for sharing ...
Glad it helped
This video has saved me so much time! I am such an idiot. I was cutting these on a table saw and making a mess in my shop. Geez!
I used to do the same thing until I saw that trick. Glad it helped and cut down the mess! LOL
See there I learned something! I was making two passes with the utility knife, when I didn't need to! Cool Beans.
That deburring tool is exactly what I need. Thanks!
Happy to help!
Just use the edge of a steel rule. Hold it at 45° and drag it along the edge.
Very Practical idea, Thanks.
Great info, Thank you!
Glad it was helpful!
I use a track saw and 80 tooth carbide blade ….it does great smooth cuts.
Agree but it gets messy and I don't have that much space. I have enough "chips" to pick up with the CNC... 🤣
Which saw? If it has a vacuum port, does it leave much debris behind?
I've used a regular 7 1/2" circular saw. The vacuum port should pick up most of it but it still makes a mess. I prefer to score and snap over the saw.
Hello, can you make series on plotter vs vinyl problems. For example when the blade pulls some of the vinyl up while cutting, etc etc.
I'll see what I can come up with. There is so much to fine tune and I can go over the basics of the vinyl vs plotter issues.
@@TheSignGuy or just some resources you have used to overcome problems
@@carloscastanyeda Play around with your OFFSET, its probably the main reason
Perfict practical Cut thanks.
glad it helped
What is the longest cut you would make with this method? Have you ever done a score & snap on the 96" side?
Across the 48" is the widest I've used this method, If it was any longer I would use a table or skill saw to cut it.
Thanks for the helpful video! Do you have any advice on cutting 90 degrees off ACM panels? Is it possible score and snap off a corner?
I'm not sure I'm following you, if you want to bend the ACM into a 90 and V groove works best. For corners, I use a corner rounder.
I am using ACM for the top of a mobile model train n-scale 3x8 foot table. What thickness are you cutting? Do you think the thickness you cut in the video will work for me with 2020 extruded aluminum braces on all four sides and across the middle? Thanks for the advice.
I use 3mm (1/8" ) ACM most of the tie and in that video. Over the span of 8ft I would use 3 braces in the center (2,4,6ft) and all 4 sides. The 3mm is pretty flimsy, ACM will bend so the more support you can give it the better.
Great video
Thank you!
Where do you purchase ACM sheets?
In the past bought it from whoever had what I needed when I needed it. Now I like to use the Piedmont Plastic Sign Grade ACM, I think it's the best out there from a quality and price standpoint.
why couldnt I have seen this about 6 hours ago. Just ordered a 2440mm x 1220mm (8 x 4) sheet and paid extra to get it cut into 4. WIll try this next time I order
We all gotta learn sometimes... Just use it for next sheet you order 👍👍
How would you go about rounding the corners?
I have a AccuCutter(.com) and use the Cornermate CM40A Table with a 3/4" rounder. A little pricey but works great, had it for 7 years and never an issue. I generally cut 1/8" ACM with ease but works fro coro and up to.040 aluminum too.
What is ACM new to this
ACM stands for Aluminum Composite Material, it is probability one of the top 3 sign making substrates in the industry. ACM just about replaced normal aluminum panels (.030,.040,.060,.080) for making signs because it has so many uses and easy to cut, bend and route. There are a lot of different choices out there, I like to stay with a .015 or .020 aluminum skins in a 3mm total thickness. ACM is a general name but if you look up DiBond they pretty much "invented" the ACM about 20+ years ago but it's twice the cost.
Use a scoring knife instead, it´s safer and easier
Great tip! Thanks!
If you treat this like drywall and cut one side fold and cut the other side it's way easier than trying to snap it. I'm actually not sure why you're doing that
the snap in my opinion leaves a cleaner edge. The pressure from the knife blade tends to curl or flair the edges.