Mustang Convertible Top Hydraulic Motor 1994-2004 Installation
HTML-код
- Опубликовано: 17 июл 2016
- Bill shows you how to install a Convertible Top Hydraulic Motor on your 1994-2004 Mustang.
Purchase Product Here:
www.cjponyparts.com/convertib...
Directly replacing your old worn out factory motor, this Convertible Top Hydraulic Motor is going to maintain a constant hydraulic pressure of three hundred to three hundred twenty five pounds per square inch, allowing for an improved raising and lowering of the top on your 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003 or 2004 Mustang.
Enhancing the movement of the top, this constant magnet motor design is going to negate the added power usage that you could expect from standard coil motors.
Subtract coil burn-out from your list of possible convertible top motor problems. Purchase this astonishing new magnet motor today and eliminate annoying motor sounds, power consumption and mechanical wear and tear today.
Check out more Mustang Convertible Top Motor parts from CJ's here:
www.cjponyparts.com/mustang-c...
Subscribe to CJ Pony Parts on RUclips here:
ruclips.net/user/subscription_c...
Thank you so very much. My friend's top on her 2003 Mustang hasn't worked in over a year. She had someone quote her a price of 500.00 to 1500.00 to fix it. I watched your video and fixed it for 8.00.
Did this a few days ago, worked perfectly. This was my first time doing a repair on my own car and I was glad to fix it myself for less than 80.00. Thank you so much!
Just completed this for my kid’s mustang and it works perfectly now! Took me about 2 hours start to finish. Thank you for this video!
After watching this video, I was able to refill original hydraulic motor and a have successful test in less than 30 minutes. Total cost for fluid and baster, $23. Taking plug out took 1 minute. Broke seal with pliers, only using thumb and forefinger finger (pull, twist,pull,twist) until removed. Putting plug in took about 4 minutes. Only using thumb and forefinger (push, twist, push, twist) until seated. Thank you 🐻
Thanks for the parts and the video! Now my old top goes up and down like it should!
I have a 2003 Gt mustang. Took me 10 minutes to get everything off. Needed a 11/16 I believe to get off the upper back seat. Now my motor was never sounded like a dying motor, but more of a whine trying to keep the top moving. Ended up taking out the plug filling it up with Lucas universal hydraulic fluid. Did the bleeding steps, and then topped off the fluid I was done. Now putting the plug back on sucked. Since it was old the plug expanded a lot. So I took a flat head and slowly pushed each side in until about half way or however far you can push it. Then my father showed me a trick to pinch and twist to get the rest on. Now it’s quiet and moving like a champ. I got 0 issues! The good part is if you do this and see you got a leaky motor you are already there to remove it! Hope this helps anyone!
Nice Swatch watch Bill @CJ Pony Parts! Used to have a bunch of them back in Elementary school. Kinda wish I had em all now. This was back in the 80's. Haha
Perfect video, thanks. Top works like a champ now.
Doing my 2004 Cobra’s this week, thanks for making this video. By the way got the many questions I’ve seen, ATF fluid is Automatic Transmission Fluid. You can get cheap $9.99 bottles at Auto stores.
Thank you soo much! I was having an issue with top going up but would go down easy and did these steps to bleed it works great
Thanks for that, 50ml of ATF and the roof works again, brilliant.
Thanks for the video buddy
My local Ford stealership wants 4 grand to do this job. Thanks. P.S. Thanks for not ruining a useful video with horrible music.
That was a very well done video, thanks
Thank you so much for your video. You made it look so easy.
Mine ended up just needing topped off. The motor was fine, it was just low on auto trans fluid. Also, the 2003-2004 Cobra seats were definitely held on by two 17mm screws, NOT two 10mm screws.
I have to ask. Why didn't you just fill the reservoir before you installed it? Would have been easier.
Great video, thanks!
Can you guys make a video on how to replace 99-04 convertible top weather striping
Anyone know of a video on replacing the entire top including the frame 99-04 mustang GT I got a like new one from a junkyard and want to swap the entire assembly... Thx!!