Hi!! I just received my A24 , I have 0 knowledge , for about 2 years I wanted to get a laser machine but it seems kind of complicated to learn , I hope I can learn with your videos, where do I start?? lol
Congrats on your new machine! To start learning I recommend starting with my earliest videos and find ones on subject and projects that you like. For project materials I recommend the Dollar Tree- they have poster board, plywood (it's smaller wood but it's cheap), anything else you would like to laser like glass! Thanks for watching!
Hi- the X12 Pro will do a great job on engraving photos on wood. I recommend using wood with a tight uniform wood grain. Oak will engrave but may not by the best type of wood- this does not have anything to do the the type of model of laser machine. Thanks for watching!
Hi there I need advise , I’m doing a project, I want to engrave on a wooden base , but I have cuts out holes two of them on the surface, can I still engrave on the surface with the cuts out holes??
I would say yes you can engrave over the holes with somethin like aluminum or the like under. Just make sure what's under the wooden base isn't too reflective and mark the back side.
Hi there thanks for the advise, I née another one if you don’t mind , so I’m putting a border on my image , I created the squares outline and add the border in the space , then I add the image at the centre , I gave it a test run but it’s not engraving the border its starts from the image , can you tell me what I done wrong or give me a tip , thanks much appreciated.
@@MRSingh-nx2xi Without a picture I'm not understanding what you have on your computer screen- maybe posting on a Facebook group for laser machines would help- this way you can add photos and video.
GRBL LPC or M3 is always a NO go. this is a downside of using auto find on older versions. this will create chaos on your engraving You need to update to 1.4.04 or higher, this was fixed.
Hi!! I just received my A24 , I have 0 knowledge , for about 2 years I wanted to get a laser machine but it seems kind of complicated to learn , I hope I can learn with your videos, where do I start?? lol
Congrats on your new machine! To start learning I recommend starting with my earliest videos and find ones on subject and projects that you like. For project materials I recommend the Dollar Tree- they have poster board, plywood (it's smaller wood but it's cheap), anything else you would like to laser like glass! Thanks for watching!
Hello, is a very good upgrade!!!
Yes it is! The setup was very easy and the results are awesome!
Hello
I ordered an X12 Pro machine and received today june, 2024, 19, an X12 Ultra....!
What is the difference between these 2 models?
Thank you
Alain
That's a great question and I honestly don't know- I saw an A12 Ultra on the website that has enclosure built onto the machine.
Could you do a video on the Mecpow G3 Laser Rotary Roller?
Hello, a small question, can I also get good results on wood with this machine for engraving photos on wood, oak and beech wood mainly.
Hi- the X12 Pro will do a great job on engraving photos on wood. I recommend using wood with a tight uniform wood grain. Oak will engrave but may not by the best type of wood- this does not have anything to do the the type of model of laser machine. Thanks for watching!
Hi there I need advise , I’m doing a project, I want to engrave on a wooden base , but I have cuts out holes two of them on the surface, can I still engrave on the surface with the cuts out holes??
I would say yes you can engrave over the holes with somethin like aluminum or the like under. Just make sure what's under the wooden base isn't too reflective and mark the back side.
Hi there thanks for the advise, I née another one if you don’t mind , so I’m putting a border on my image , I created the squares outline and add the border in the space , then I add the image at the centre , I gave it a test run but it’s not engraving the border its starts from the image , can you tell me what I done wrong or give me a tip , thanks much appreciated.
@@MRSingh-nx2xi Without a picture I'm not understanding what you have on your computer screen- maybe posting on a Facebook group for laser machines would help- this way you can add photos and video.
GRBL LPC or M3 is always a NO go. this is a downside of using auto find on older versions. this will create chaos on your engraving
You need to update to 1.4.04 or higher, this was fixed.
Good to know- I haven't seen any issues on my system engraving. Yes- my Lightburn is a little out of date! Thanks for sharing!