Upgrade Anycubic i3 Mega - Stepper Motor Drivers TMC2208 | Marlin Firmware
HTML-код
- Опубликовано: 10 сен 2024
- Upgrade Anycubic i3 Mega - Stepper Motor Drivers TMC2208 | Marlin Firmware
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
🛒 Anycubic I3 Mega: shorten.asia/8...
🛒 TMC2208 Drivers: shorten.asia/C...
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
📎Marlin Firmware: drive.google.c...
💻💡 Facebook Group 💡💻
► / 403errorvn
Social Media -
► Forum - www.4evn.com/
► Page - / 403errorvn
► Facebook - / bamanh.official
► Insta - / 4e_projects
► Email - contact.manhvd@gmail.com
Become a channel Sponsor -
💵 PayPal - paypal.me/bamanh69
Tool -
🔵 RIDEN RD6018W : shorten.asia/t...
🔵 3D Printer : shorten.asia/q...
🔵 Soldering Station T12 : shorten.asia/A...
Recommended Gear -
🔵 Laptop Asus TUF Dash
🔵 Camera Sony A6300
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
- DIY list: • How To Make UPS For Wi...
- Projects Arduino list: • DIY Digital Soldering ...
- REVIEW: • 5.5 Watt Diode Laser E...
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
Thanks for tuning in as always!
#DIY #Anycubic #3dprinting
Very nice 👍🙂.
Thank you! Cheers!
hello, I've changed the drivers as shown here and while setting the vref 2 of them measure 0.030 V and one of them 1.8V and can't be adjusted. what could be wrong?
I think it might be experiencing some issues.
@@4EProjectsChannel Unfortunately, I short circuited one of the drivers when adjusting it with the metallic screwdriver that the Anycubic provided. I highly recommend using a coated screwdriver and unplugging the motors while adjusting.
I have some lame problems. Updated the firmware with original mega stuff. I also have tmc2208.
But the stupid thing starts printing in mid air. Then rices even more . It doesnt do the correct way of lifting Z then decline down to the bed.. ?? im using cura. When I tried the original owl G code which is repetier host. Then it wont even lift itself at the beginning. just drags the nozzle into the middle..
Hello, with the issue you're facing, you should update the software for your 3D printer.
@@4EProjectsChannel
what else can I update? have the latest version from anycubic website
Show
what setting on multimeter to adjust the voltage? also when adjusting we need to turn on the printer right?
Hello, you set the voltmeter to the voltage range and then adjust the voltage regulator.
Don’t you have to flip the cable connections for the stepper driver for it to work?
Hello, In my Firmware section is pre-programmed.
No need to rewind it.
Great Video, when do i use the "normal" firmware and when the reversed version?
You have to use the normal firmware, if you swap the motor wires. You have to use the reversed firmware, if you don't swap the motor wires.
How do you know that the 0.86V is correct value? Is it a tests experience ?
You can read its datasheet.
Does it have an effect on print quality, or is it just acoustic?
@@BoloSparks that good news. i have few in my drawer but i was lazy to replace the original drives. but ur answer motivated me.
The link of TMC2088 is fail.Any version of TMC2088 driver is ok?
shorten.asia/CyXxEBEE
Can I use this firmware for Anycubic Mega S with TMC2209 or must I use another marlin firmware?
Hello, they can use the same firmware.
very nice. I've been wanting to do this for my i3 mega. @ 2:06 what are you testing for? Is there a guide on what to look for here? I know little about the electronics aspect.
Hello, you can upgrade it, it would be great.
At 2:06, I adjusted the output line for the engine by measuring the voltage at the throttle position sensor at approximately 0.85 volts.
@@4EProjectsChannel Thank you! I did do some more research and I think I can handle the adjustment🤞😅 I have ordered the drivers!
@@4EProjectsChannel I did the upgrade today. Works perfectly! Thank you for your time.
@@4EProjectsChannel How do you know that the 0.86V is correct value? Is it a tests experience ?.
What version off Stepper Motor Drivers did you use? V1.2? Thanks.
Can firmware be used for tmc s2209 v3.1
I haven't tried it, but if it's not necessary, you can use my firmware.
does this work with a mega X??
They are similar to each other.
Can I use the stock board and do I need to update any firmware?@@4EProjectsChannel
@@BoloSparks nah upgraded to TMC2209 and they are extremely quieter now. Stock ones are noisy af