Видео

yes, sure

That's so great

I looked up your machine, it has thunderbolt 3 connection. So it is totally possible to use this eGPU.

@@4EProjectsChannel thx mate...for ur reply

You need to adjust the baud rate.

If posible using only cronos board?

​@@4EProjectsChannelgrbl code on board need be modified?

Sorry, but no.

Hello, you just need to change the HC05 module parameters to be able to use it.

Gotcha... And to do so... Just follow the video?

it is the battery protection circuit

You just need to connect the eGPU to the Laptop via the Thunderbolt port

lõi đường kính ngoài 30mm, lõi đen cuốn cỡ 30 vòng sẽ được ~60-70uH

Здравствуйте, я понимаю вашу проблему. Вам необходимо измерить и откалибровать формулу на основе вашего датчика, у меня его нет, поэтому я не могу измерить его для вас. Мне жаль

@@4EProjectsChannel Как я понял у меня датчик термопара (модель A1322) а для вашей схемы нужен A1321 с термистором (термо резистор) Как я понял просто рассчитать верхний резистор дарителя (480R) не достаточно. Так как хоть и у меня сопротивление датчика растёт линейно но возможно будет работать не корректно. Мне сказали что проще купить ручку Lukey 702 и там точно термистор.

Hello, I looked up your device does not support the Thunderbolt connection standard

Hello, please check the power supply for this eGpu

i use thunderbolt cable

@@4EProjectsChannel I understand now thunderbolt cables can go into type c ports right?

@@4EProjectsChannel I thought thunderbolt and type c is the same but it wasn't

gửi e mail e gửi qua nhé

Your RX7600 xt can be mounted

Your RX7600 xt can be mounted

Hello, you only need to purchase the following components: 1. eGPU Dock (link available in the video description). 2. ATX power supply: choose one with a capacity of over 500W. 3. A graphics card such as RTX3050, 3070, or 4060, etc., depending on your needs.

Have you tried using it yet?

The PZEM module will return the energy consumption in kWh and the power of the load in Watts.

​@@4EProjectsChannel I did something similar to this for my homework, but this question always stuck in my mind. When I do this, it tells me a value of 0.18 kW at idle. Is this value hourly or measured per second? For example, Your measure is 22w, this value is the power of the lamp per second or hour. So what I'm wondering is these watts, kwh, Are the current values exactly in seconds or hours? I'm very curious about this. Thank you for replying.

great

Try disabling the integrated graphics card on your computer before connecting the external GPU.

@@4EProjectsChannel Ok finally It works! The answer is following - it is quite important to buy good power supply (with standard gold or silver and enough power) and second - it is important to use usb type C with power (in the middle) on the dock station overwise your computer didn't recognize it. One more benefit of using such scheme is that you could unplug the main supply cable of laptop.

Hello, I have left the link to the code file in the description of the video.

You need to turn off one card before attaching the other.

Ask copilot :-) Get your laptop cpu specs & ram, intel iris xe etc, give all those specs to Co-pilot, tell him what you would like to do, ask if it's a good idea with this external dock and what would be the best solution for the external graphic card. That's what I did... 11th Gen Intel(R) Core(TM) i7-11370H @ 3.30GHz 3.30 GHz 32.0 GB (31.8 GB usable) 64-bit operating system, x64-based processor Intel® Iris® Xe Graphics Dedicated GPU Thunderbolt 4 Apparently going higher than a NVidia 3060 would be stupid and even problematic, so I know what to get. :-) My CPU sucks, it's a bad version... other 11th Gens are better and can handle a 4060. So yeah, all depends on your cpu specs & ram, if you want the best card to buy accordingly.

​​@@Eyesandears2011My laptop does not have thunderbolt port 😢, do you have any solution for this? But i have robust i9 13900h processor 🔥

@@userioiowr9462 No, I do not have a solution for your laptop. Maybe you have a different port than Thunderbolt? Again, ...you might want to ask co-pilot. 🙂

Hello, I have looked up the model of your laptop, and it does not support Thunderbolt connectivity.

@@4EProjectsChannel Thank you Buddy

Hello, thank you for your feedback. I will make improvements in my future videos.

i use a4988 module

@@4EProjectsChannel tank you.

i think your current sensor is broken

​@@4EProjectsChannelreally? what is the another possible causes for the issue? What about the IR2104? The IR2104 in SD and IN measured pulsing 0.8v with multimeter. Is it genuine?

ko nha, tại file tải về có code thực hiện cấu hình cho module rồi.

Đợt em có cấu hình để test truyền nhận thì giờ không cần phải can thiệp đúng không ạ, code tự cấu hình lại cho mình phải ko a.

Hello, I have provided the BOM list at the link above.

Hello, I have provided the BOM list at the link above.

yes

Hello, you can download the software here: [drive.google.com/drive/folders/10h1Fj04YktBXWsxBID_4IdMsdYRjT13O?usp=sharing](drive.google.com/drive/folders/10h1Fj04YktBXWsxBID_4IdMsdYRjT13O?usp=sharing)

mạch này đang dùng esp8266, chuyển esp32 được nhưng phải sửa

@@4EProjectsChannel ờ 😁😁

thanks 😘

Halo, saya mencantumkan tautan mesinnya di deskripsi video

❤️❤️

Hello, I have provided all documents (including circuit diagrams) below the video. Please click on the provided link to download

nice!