GRBL Laser - Wireless LASER Control via Bluetooth HC 05

Hello friend, GRBL Laser - Wireless LASER Control via Bluetooth
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
🔖 File GRBL, setting LightBurn,.. : drive.google.c...
💻💡 Facebook Group 💡💻
► / 403errorvn
Social Media -
► Forum - www.4evn.com/
► Page - / 403errorvn
► Facebook - / bamanh.official
► Insta - / 4e_projects
► Mail - [e-mail]
Become a channel Sponsor -
💵 PayPal - paypal.me/bamanh69
Tool -
🔵 RIDEN RD6018W : shorten.asia/t...
🔵 3D Printer : shorten.asia/q...
🔵 Soldering Station T12 : shorten.asia/A...
Recommended Gear -
🔵 Laptop Asus TUF Dash
🔵 Camera Sony A6300
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
- DIY list: • How To Make UPS For Wi...
- Projects Arduino list: • DIY Digital Soldering ...
- REVIEW: • 5.5 Watt Diode Laser E...
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
Thanks for tuning in as always!
#bluetooth #laser #grbl

[@4EProjectsChannel]

Thanks for watching 😉😉😉
Subscribe to my channel if you like❤

[@robojassi9187]

Good

[@4EProjectsChannel]

thank you very much

[@primetimeuga]

So you have to "program" the HC-O5 with an arduino prior to connecting it to your grbl controller board?

[@4EProjectsChannel]

Hello, you just need to change the HC05 module parameters to be able to use it.

[@primetimeuga]

Gotcha... And to do so... Just follow the video?

[@bowlingaddictionmx]

i have same board and hc 05 connect and vinculated with bluetooth module and no work.. dont receive and send data you have to mod the arduino software for this board?

[@4EProjectsChannel]

You need to adjust the baud rate.

[@bowlingaddictionmx]

If posible using only cronos board?

[@bowlingaddictionmx]

​@@4EProjectsChannelgrbl code on board need be modified?

[@chadhoward1982]

6 pin BT board into 4 pin socket, which pins did you connect to the atomstack?

[@4EProjectsChannel]

4 pins: VCC - 5V, GND-GND, TX-RX, RX-TX

[@mamadoubapassioninformatique]

Hello. Is it possible to use the Laser module of the Ender-3 S1 with the GRBL software?

[@4EProjectsChannel]

thank you for comment,
I will exlore

[@djockersan2312]

А как подключить программу по блютуз я не понел?

[@4EProjectsChannel]

На компьютере включите Bluetooth, затем подключитесь к модулю HC-05. После успешного подключения на компьютере появится соответствующий COM-порт лазерного устройства.

[@PedroGomes_27]

any way to make it wifi?

[@4EProjectsChannel]

Hello, to use Wi-Fi, you need to use the MKS DLC32 board. It comes with built-in Wi-Fi integration.

[@trungkienpham2122]

Light burn có ble hả 😂😂😂

[@4EProjectsChannel]

HC-05 kết nối tạo cổng COM, trên LightBurn kết nối với máy từ xa qua đó🤣