How to Polish Stainless Air Cleaner - Evan's Polishing and Detailing
HTML-код
- Опубликовано: 27 авг 2024
- Evan from Evan's Detailing and Polishing doing a quick walk through on how to polish a stainless steel air cleaner. All the products in this video are available on goshineon.com/shop.
All of these products are available at www.amazon.com... or by the individual links.
Makita ga7021 amzn.to/2RPDBoo
6,000 rpm
Dewalt D28499X amzn.to/2JZqw9j
6,000 rpm
Makita 9927c amzn.to/2TaKL8n
3500 rpm variable speed
Dewalt dwp849x amzn.to/2qIZ7j9
3500 rpm variable speed
15 mm orbital
amzn.to/2VWSM2l
Porter Cable
amzn.to/31saU5d
White cotton towel options
12 x 14 (100 pack) amzn.to/2SHAm3r
12x 12 (24 pack) amzn.to/2C5evLU
Makita 5" da or random orbit
hook and loop amzn.to/2SxCY3r
Extension cords
100' 10 gauge amzn.to/2Sqclko
50' 10 gauge tri tap amzn.to/2t6PHPJ
100' 12 ga amzn.to/2GgOFJJ
50' 12 ga amzn.to/2TA5nXs
20 ton jack
amzn.to/3343V4i
20 ton air jack
amzn.to/2qSNTvJ
20 ton stubby jack for low axles
amzn.to/2PzRc5e
20 ton stubby air jack for low axles
amzn.to/2JA9ShK
Getting clean after polishing.
Suave men’s care 3 in 1
amzn.to/37u6K0r
Lava bar soap
amzn.to/2ZxfZda
Under new law I have to proclaim these links are associate links and I get paid for the sales of these products.
We have stainless tank raps that are pretty rough on the bottom half. So my question is, can a sand that like aluminum and then polish with the stainless rouge. Or maybe there’s a different trick to smoothing out stainless"
You can sand it like aluminum only use less aggressive grits. Don't go any deeper than you need to and when sanding at 600 don't stop until it looks super shiny then buff. If it isn't already shiny it isn't ready to buff.
Evan Steger. Thanks, I’ll have to do some experimenting
Spotted an accert under the hood 🥰
Thanks for watching.
What’s the name of this song at the beginning. Best videos and direction on RUclips!!!
Not sure the song name at all to be honest. Thank you for the compliment.
Can do video on sanding Dimond plated aluminum
I don’t sand diamond plate. Waste of time and money for not enough results. Hard to recoup the cost.
Do they make small 3 or 4 inch buff wheels for getting into tight spots? Maybe for small air grinders...?
Evans ocupo detú ayuda
They do. Not sure where to get them but yes they do.
Would you please put the information about the wheels and compound in the information section
Thanks in advance
Hauling Faith goshineon.com/shop. 2 step stainless kit.
Evan Steger thanks I placed my order
I did this method and it left haze marks I used the orange and brown then yellow and green but still didn’t come out. What can I do next?
If you used brown rouge on stainless it definitely will get cloudy. Tripoli is too big of an abrasive and the wrong mixture to polish. I mean it can polish but it won't polish great. You need stainless compounds to properly polish. Black, green or yellow. But if rough you have to start with a black compound and finish with either green or yellow. Not all black rouges are the same. My black that we sell on goshineon.com is a quick cutting and good gloss coloring bar. Then finish with green or yellow rouge. That is the best route.
Ok, I have a question. I have been cutting and polishing my tanks. At what speed should I be cutting, and what speed should I polish? I have been cutting between 800 and 1400 depending on how rough the area is and I have been polishing between 1500 and 1800. Is that ok for my Aluminum tanks and wheels? or should I be polishing at a higher speed? Thank you in advance!
I have videos here on how to polish tanks. I run 6,000 rpm but it’s not safe and not for everyone. I tell guys to start at 3500 and move up when you are ready. 800-1400 would take forever to build heat.
@@EvanStegerMetalPolishing I did find that it takes longer to build heat. I have watched a lot of your videos to be sure my thoughts on the stages and process was right. I just wasn’t sure about the speed because it was taking longer than I thought. Thank you for your reply. I’ll step it up. I definitely understand the 6,000 speed. One of my grinders will do 20,000 rpm. It’s a beast. Not for everyone for sure. I’ll tell you this tho, I have a lot of respect for polishers such as yourself. I spent two days detailing and polishing my truck and I’m not out of shape but I will say, I’m pretty sore! Ha ha
My man
Thank you bud. Hope all is well.
Carnal como se piden los discos esos o como le ago para conseguir uno me podrias decir
goshineon.com/shop carries all the Buffs and pads you see used here.
What do you wipe down with rebel red
Bood droe we use pipe dream now go take off the excess grease.
I always hear you say "rake" the wheel to clean it. What is used as a "rake"
0002ken check out my rake video.
Ok thanks evan. I will see if i can find one. You do nice work. Wish you were near me to do my truck. Nobody does polishing around here. But i do ok.
If it's your own truck or company's truck I just use the step treads to rake the wheel. Works for me just fine
what type of grinder do you use?
TPA TRUCKING LLC Makita ga7021
Isn't that a lot of rpm on the wheels? Makes for a lot of heat...
Stainless steel likes getting hot. The heat is what helps make it shine again.
um abraço Elias do Brasil
English?
Do you Ship to sweden?🙂
We can. Thanks for watching.
Evan Steger, do you have an email?
I would like to ask you business questions if you don't mind sir. Thanx.
Andres Madrigal evan@goshineon.com
cant hear shit with all the noise in the background
Sorry. I plan to redo this video in the near future with better audio. Sorry for the inconvenience.