Beginner: planer, jointer, table saw, jig saw, miter saw, bar clamps... When I was a beginner I had a skill saw, drill and hammer. I don't think people know what beginner means sometimes.
I am a beginner . I don’t have a planer or a joiner. I have a cheap tracksaw , drill and jigsaw . A couple small clamps from Amazon and safety glasses .
@@hvwoodcreations6278 pallet wood is the new toilet paper. ;) Cheap wood might be a little bit misleading... using wood the wrong way is more correct here. I would have used harder wood and standing annual rings for the table top.
the author does like to from scratch, shaping and trimming wood from large blocks into fine finished products. ruclips.net/user/postUgkxD-QRFQz730FJEh4f9BYSf-nkIMIC9hL_ as another reviewer mentioned, most projects require a lot of high-dollar equipment that most of us dont have the room or budget for. But, knowing how to do these things, even if we wont be able to practice the full stack project, is still great.
Mate , a quick tip for beginners , ALWAYS alternate the boards / growth rings radius , it helps to prevent cupping . And time taken to ' joint ' the boards will give a better job . Nails .....hmmmm. A biscuit jointer for beginners is a good tool , or use dowels .
@@darrenpodger7294 Dowels and biscuits don't actually add any strength per se. The glue (even without dowels or biscuits) is so strongly bonded, that you could put a glued panel under a hydraulic press, the wood will literally split in half before the glued joint separates... because the fibres of the wood itself are actually weaker than the bond of the dried glue. As an example, from a channel dedicated to playing around with hydraulic presses... ruclips.net/video/8jESD2-lv-M/видео.html The actual point of dowels/biscuits, is not to add strength, but to hold the panel fast while clamped until the glue has done it's job. Without dowels, biscuits (or in this case, headless nails)... one can very easily experience shifting as the glue sets, only resulting in more work needing to be done to re-level the piece. Personally, I found the use of nails here for beginners quite genius. It enables large projects on a very tight budget. Those who have the money for say, a festool domino tool, it will only make their lives easier due to not having to whack the pieces together, but for a beginner or those on a tight budget, this works absolutely
@@grahamb7947 I would not put dowels and biscuits in the same category when it comes to strength. I agree good wood glue is going to be adequate for strength. On a panel dowels do not add any strength, but on a small joint it does. Sorry, I don't find the nail idea of any us here. He should just glue it together and that be that. By the way you can get dowels and drill dowel holes pretty cheap.
I hate to be critical but as someone that would like to learn, I'm getting nothing from this video. Other than frustrated because there's no instructions
It means do not glue and/or screw the aprons to the top in a way that doesn't allow for wood movement as doing so will eventually cause the joint to fail and it will crack. Instead don't glue at all and use a figure 8 or z-clip fastener to attach the top. These z-clips require grooves to be made in the aprons so that when the top expands or contracts, the fastener will move with the wood instead of forcing it to stay put (this is what causes it to crack). I'll find a video showing this.
This is a perfect example of just because you have expensive tools doesn't make you a better craftsman. This was hard to watch. If you have a jointer and a planer you should have been able to make that table top flat. That wood was gorgeous, DON'T STAIN IT!
Yeah..beginner's could do that..!! Easy..just make sure you have All the tools you dont need the bandsaw... get a circular saw n a guide to keep your cut straight
Even taking a plank that is not square and true and getting it to an accurate piece of wood on which you can cut joints for perfect fits, is more difficuit than meets the eye.
This is an outstanding INTERMEDIATE woodworkering project. Seriously! What beginner do you know knows the first thing about planing? Even by hand? What beginner do you know knows how to proper cut a mortise and tenon? These are are not beginner techniques and this project has to ve drastically changed to suit a novice woodworker. For example, the table top should be made out of a solid core door so that it is completely flat. The joining should either be butte joints or maybe half laps for the ambitious beginner. I usually despise this type of comment because it's on EVERY woodworking video ever, but it's definitely warranted here.
Beginners? You have a planer and a jointer. DIYers who have woodworking experience don't even have those two tools, and this is titled for beginners? Whoa mind blown.
I found the translation of his title to english caused a grammatical error. The “beginner” was supposed to reference the skill level of this project, not his ability. Which makes sense if u watch some of his other vids. Dudes pretty good. A lil rough, but got some skill. Hope this helps.
The method you used for tenoning on the table saw was quite dangerous and is likely to lead to kick back. You should create a tennoning jig that holds the piece in place while vertically running through, otherwise a wobble at the other side of the blade will send it flying.
You might want to think about lowering the blade on your table saw when using the planer on a combination machine. That’s a good way to saw off your hand, or your helpers hand, or shoot a piece of material across the room or through a window.
Uses expensive shop tools for cuts and joining that can be done without expensive shop tools then uses nails as dowels which are the absolute cheapest item for a beginner.
wouldn't you want to joint a face flat then joint an edge parallel to the jointed face. then plain the board jointed side facing down and then rip to final width?
I can see the joy on the buyer’s face at TK Maxx, thinking of the 500% mark up. Also, the grin on the face of the Romanian car washer when they export it to their brothers for resale in Chechnya.
Remember some of us don't have all that fancy equipment especially beginners like me. So if you show us beginners using the basic tools safely i think you will nail it. Me i have jig saw,circular saw,router,dermal and a dril,impact set oh and clamps lol that's it. So I turn to the smallish stuff to learn and make money to buy the nicer things.
I don’t think when he said beginner that it was about his power tools it was about the simple design around making this desk… I have a lot of power tools and I just built a desk I still consider myself a beginner because I put all my tools away for a couple years and then drag them all out to try to do something again and have to remember the skills that it takes to do each one. I really enjoyed watching him make this since I’m still going through Nick‘s and cuts and slivers from my last project.
Why would you use nails and not dowels for top and also don’t glue top to the bottom that will expand and shrink and your have cracks after time. Need to do it right.
wow, commenters ripped him a new one! As a beginner, I have a chop saw and a handheld planer. what was hilarious tho, is the sped up version of a roster crowing, lol!
Why all the hate? Everyone complaining it is not a beginner project and the expensive tools and shit. Those are the tools needed to work with wood and the table has a simple design anybody can attempt to make even as a beginner. Use whatever knowledge/ideas you can get out of this video and add your own touch to make it better if you wish, hating on people that are trying to share something good with you is just low, don't do it.
find a way to stop it at 12:08.. it is a twisted sister. the front left foot doesn't touch, like a 1/4" space. sloppy staining too. He is always sanding, like this is sculpting.
So after scrolling thru the comments, I see a trend of two types: One bitching abt his equipment and how it's not what a typical beginner would use... and the second bitching abt his choices during the process... Just viewing from my fairly basic woodworking experience, both are true. There's a lot of equipment there that a beginner wouldn't have, and there's a lot of choices made that even an intermediate woodworker would have thought twice about. Classic example of buying your way into a trade without properly learning the fundamentals. But then again, this is RUclips and he got paid by us watching it, even to criticize and notice things we wouldn't do... so kudos. Just use this video as a learning exercise in what not to do, and what tools you REALLY need.
Hi Woodworking Guide. I agree with most of the comments on this video. It's a great project, but simple projects for beginners. The ultimate in misrepresentation. Why not just promote it for what it is rather than try to mislead people who see right through it in seconds. Although, presenting it as you did got you 1.1 million views and 436 comments, which is honey to advertisers. Integrity = 0 Money making = 10
Am I the only one that thinks it’s crazy he has all these pro tools and used nails in his top, instead of biscuits or pocket holes or simply just a glue up.
Yeah, here we go again. He is using framing lumber, it's not dried, so it will split, shrink, and warp. If he is planning on this being an out side table, the glue he used will fail within a year. This is a complete waist of time. Please don't try and duplicate what he has done here. There are a lot of really good woodworking videos on youtube, please check them out.
Actually, indoors or outdoors, this will fail. Legs to styles are glued cross grain and the wood will expand and contract in opposite directions, causing greater stress on the joints. The top glued and screwed up is even worse! Never glue the top to the base, as the top will expand and contract the most! Just a few screws with elongated holes in the base to allow for wood movement will help prevent the top from cracking and cupping. Pine is a soft wood and is more susceptible to movement due to the environment. So, even greater care and design planning is ideal to a better, longer lasting build.
The beginner who has all the professional tools. Just needed to know what to do with them. Just run to Home Depot and spend $4,000 and your ready to go. Beginner check mark ✅.
Nowadays title should sound different like: project for beginners with all the tools presented in the video or with a budget that could afford to buy all the tools😅
A lot of people that make this kind of videos maybe think is fun or a joke to say it's for beginners or maybe they want to show something simple in a overcomplicated way to impress...anyway, it's really deceiving others, specially people that are new to woodworking or are curious on how they could start woodworking. If you really want to show something for beginners then think like a beginner. First, stop using advanced tools, no beginner have those. Woodworking tools for beginners are basically three: a circular saw, a jigsaw and a drill. More than 75% of beginners projects can be done with just those three (along with some basic manual and measuring tools of course). A fourth tool recommended is a sander, with it people can do a comparable result to a planer and achieve better finishes which help a lot. We are here to encourage others to keep doing and try to do new things, not turn them off.
He wasn't using a drill press it was a mortiser with a mortising bit. You would need a mortising attachment to a regular drill press in addition to the mortising bit to perform the same function.
![making the strongest 3-way leg joinery / castle joint [woodworking]](http://i.ytimg.com/vi/OJ8V_rzwxh0/mqdefault.jpg)
Beginner: planer, jointer, table saw, jig saw, miter saw, bar clamps... When I was a beginner I had a skill saw, drill and hammer. I don't think people know what beginner means sometimes.
Don’t forget the hollow chisel mortiser
@@davidjcarpenter that item is freaking OP... every woodworker dream machine in their shop
I thought the exact same shit lol
I am a beginner . I don’t have a planer or a joiner. I have a cheap tracksaw , drill and jigsaw . A couple small clamps from Amazon and safety glasses .
All those tools and no hammer!!!
Can’t wait to see the tools he’ll
use for his advanced projects!
Haha… died
Isu technology, not currently available to the public.
🤣🤣🤣🤣🤣🤣
I was thinking the same thing!
Thousands of lifetime projects with Woodglut plans.
Projects for beginners, yet start by using tools and machines that beginners wouldn’t have! Great!
If you’ve meant „beginner“ as in „using professional tools the wrong way and make a shitty product out of cheap wood“ - you’ve totally nailed it.
Nailed it? Was that a pun at having used nails to create the panel instead of dowels or biscuits? 🤣
@S B Cheap wood? No such thing these days. Pallet wood is like gold these days.
@@hvwoodcreations6278 pallet wood is the new toilet paper. ;)
Cheap wood might be a little bit misleading... using wood the wrong way is more correct here. I would have used harder wood and standing annual rings for the table top.
@@grahamb7947 not intentionally 😂
Very dangerous cuts at 6:37...
the author does like to from scratch, shaping and trimming wood from large blocks into fine finished products. ruclips.net/user/postUgkxD-QRFQz730FJEh4f9BYSf-nkIMIC9hL_ as another reviewer mentioned, most projects require a lot of high-dollar equipment that most of us dont have the room or budget for. But, knowing how to do these things, even if we wont be able to practice the full stack project, is still great.
Mate , a quick tip for beginners , ALWAYS alternate the boards / growth rings radius , it helps to prevent cupping . And time taken to ' joint ' the boards will give a better job . Nails .....hmmmm. A biscuit jointer for beginners is a good tool , or use dowels .
Definitely dowels was thinking same , stronger for longer.
@@darrenpodger7294 Dowels and biscuits don't actually add any strength per se. The glue (even without dowels or biscuits) is so strongly bonded, that you could put a glued panel under a hydraulic press, the wood will literally split in half before the glued joint separates... because the fibres of the wood itself are actually weaker than the bond of the dried glue.
As an example, from a channel dedicated to playing around with hydraulic presses... ruclips.net/video/8jESD2-lv-M/видео.html
The actual point of dowels/biscuits, is not to add strength, but to hold the panel fast while clamped until the glue has done it's job. Without dowels, biscuits (or in this case, headless nails)... one can very easily experience shifting as the glue sets, only resulting in more work needing to be done to re-level the piece.
Personally, I found the use of nails here for beginners quite genius. It enables large projects on a very tight budget. Those who have the money for say, a festool domino tool, it will only make their lives easier due to not having to whack the pieces together, but for a beginner or those on a tight budget, this works absolutely
@@grahamb7947 I would not put dowels and biscuits in the same category when it comes to strength. I agree good wood glue is going to be adequate for strength. On a panel dowels do not add any strength, but on a small joint it does. Sorry, I don't find the nail idea of any us here. He should just glue it together and that be that. By the way you can get dowels and drill dowel holes pretty cheap.
As a beginner myself, I look for people that know what they are doing so i do it the right way instead of having to relearn after years. Any tips?
@@jamasottinger6263 yeah delete this video from your memory banks.
Title should be: Woodworking for beginners with access to a professional wood shop; build a table badly
yeah this video is absolute trash
A lot of extra work
I hate to be critical but as someone that would like to learn, I'm getting nothing from this video. Other than frustrated because there's no instructions
Exactly.
This is exactly what I came on here to say. I love woodworking. I do not have a table saw or planer SO…. I improvise or at least try.
Been doing woodwork for years and have about 20% of these tools.
I love when they say easy projects for beginners, and use all kind of pro tools
And all you need is an entire commercial wood shop to make it.
Do not glue the top to the frame - WILL CRACK 100%, connect it floating to allow expansion and contraction
Came here to say the same. Failure waiting to happen.
Not a pro, what do you mean by "connect it floating"? Pretty sure I probably know what you mean just not precise on what you're referring to.
It means do not glue and/or screw the aprons to the top in a way that doesn't allow for wood movement as doing so will eventually cause the joint to fail and it will crack. Instead don't glue at all and use a figure 8 or z-clip fastener to attach the top. These z-clips require grooves to be made in the aprons so that when the top expands or contracts, the fastener will move with the wood instead of forcing it to stay put (this is what causes it to crack). I'll find a video showing this.
This the figure 8 fastener: ruclips.net/video/-OvktNWtukk/видео.html
@@fmacleod oohhh I've seen these, didn't realise that's what they were for. Thanks!
This is a perfect example of just because you have expensive tools doesn't make you a better craftsman. This was hard to watch. If you have a jointer and a planer you should have been able to make that table top flat. That wood was gorgeous, DON'T STAIN IT!
BEGINNERS?????? OK SURE
Yeah, bro. Beginners don't have planers, jointers etc. You're just fishing for views.
Yeah..beginner's could do that..!! Easy..just make sure you have All the tools you dont need the bandsaw... get a circular saw n a guide to keep your cut straight
woodworker beginners mate not PubG if you get the point :))
Dwf not beginners. Yea its simple...but beginners don't have planners and jointers just chillin in the garage.
Even taking a plank that is not square and true and getting it to an accurate piece of wood on which you can cut joints for perfect fits, is more difficuit than meets the eye.
This is an outstanding INTERMEDIATE woodworkering project. Seriously! What beginner do you know knows the first thing about planing? Even by hand? What beginner do you know knows how to proper cut a mortise and tenon? These are are not beginner techniques and this project has to ve drastically changed to suit a novice woodworker. For example, the table top should be made out of a solid core door so that it is completely flat. The joining should either be butte joints or maybe half laps for the ambitious beginner.
I usually despise this type of comment because it's on EVERY woodworking video ever, but it's definitely warranted here.
Same here.
Nails bend, to anyone that might attempt this just use dowels.
"Super easy beginner project! All you'll need is some rough lumber, knowledge on how to mill it, and $15,000 worth of tools!"
And then still build a shit table
Right
Haters
@@kllgrogto5838
👍🤣😂🤣
Beginners? You have a planer and a jointer. DIYers who have woodworking experience don't even have those two tools, and this is titled for beginners? Whoa mind blown.
If woodworking is your hobby, you should have a jointer and planer.
Mantap
Pengerjaannya sangat rapi👍🏻
Terima kasih ilmunya bro
“For beginners”. First 20 seconds has 1000’s of dollars of tools.
Gotta start somewhere
@@jkmurphy3 yes, but staring somewhere shouldn’t cost thousands of dollars. It should be the opposite.
I found the translation of his title to english caused a grammatical error. The “beginner” was supposed to reference the skill level of this project, not his ability. Which makes sense if u watch some of his other vids. Dudes pretty good. A lil rough, but got some skill. Hope this helps.
No, it doesn’t. Beginners normally don’t have expensive equipment, therefore, without the equipment, it’s not a beginner project.
you could do it with hand tools it would just be slower
The method you used for tenoning on the table saw was quite dangerous and is likely to lead to kick back. You should create a tennoning jig that holds the piece in place while vertically running through, otherwise a wobble at the other side of the blade will send it flying.
Nice work not for beginners but subpar tolerances for exactness. Table was noticeably wobbly and did not sit flat.
You might want to think about lowering the blade on your table saw when using the planer on a combination machine. That’s a good way to saw off your hand, or your helpers hand, or shoot a piece of material across the room or through a window.
Uses expensive shop tools for cuts and joining that can be done without expensive shop tools then uses nails as dowels which are the absolute cheapest item for a beginner.
If this is a beginner level, then i would like to see how pro level looks like 😁👍
wouldn't you want to joint a face flat then joint an edge parallel to the jointed face. then plain the board jointed side facing down and then rip to final width?
Yes thats typically how its done lol, FEE (Face, Edge, End)
Why? Why would you use a supervisor method during a "beginner" project 😂
I can see the joy on the buyer’s face at TK Maxx, thinking of the 500% mark up. Also, the grin on the face of the Romanian car washer when they export it to their brothers for resale in Chechnya.
That beginner has a nice set of tools!
All of those “beginner” tools are so cheap and useful. Definitely don’t need advance tools like a mallet
Can't wait to start my first beginner project
Remember some of us don't have all that fancy equipment especially beginners like me. So if you show us beginners using the basic tools safely i think you will nail it. Me i have jig saw,circular saw,router,dermal and a dril,impact set oh and clamps lol that's it. So I turn to the smallish stuff to learn and make money to buy the nicer things.
I don’t think when he said beginner that it was about his power tools it was about the simple design around making this desk… I have a lot of power tools and I just built a desk I still consider myself a beginner because I put all my tools away for a couple years and then drag them all out to try to do something again and have to remember the skills that it takes to do each one. I really enjoyed watching him make this since I’m still going through Nick‘s and cuts and slivers from my last project.
The title says "For Beginners" then shows several thousand dollars worth of power tools in the first 30 seconds.
😊 You can do all this by hand UNLESS you’re a beginner 😂😂
This is not for beginners only for profenionalas i think nice work
Nice video, learned lot. I'm a beginner. What finish are you spraying onto the desk? hope to hear from you, many thanks in advance
Thanks
Very nice, this is what i call working from home, great job!
Great build! But I wouldn’t say this is for beginners because you have some very expensive tools you are using right away in the beginning. Lol
Agreed, a new woodworker probably won't have a jointer and planner, would be nice
Jddjcddjhssdkbcssjbcwwjhcuxwwdujjcedkjjkceejeuckkwdjsjnxwennnnnxnnsdjbxxxwdjnxwskkddmmsdmmmsddkmddmssmssmmwsuddjjcjddjjjcdddjcjddjcdddjcxkwxwwixbw
Totally agree, the only thing iv got is a cheap mitre saw. All the rest are hand tools
He did a lot of beginner’s mistakes. This table is ugly
It’s got a beginner finish on it too!
Why would you use nails and not dowels for top and also don’t glue top to the bottom that will expand and shrink and your have cracks after time. Need to do it right.
Great woodworking projects for beginners: all you need is a table saw, planer thicknesser, jointer, mitre saw and every other shop tool going.
Don't forget the hollow mortiser
@@fmacleod and a compressor, and paint gun
Yea for beginners with every single tool. It’s really easy to build that with all your equipment.
I don't understand how having such good tools is so messy... I wish I had that edger and the miter saw... one day
Thanks for showing why we use wooden dowels instead of nails for glue up.
Im a big fan for woodworking...i really like to work with wood
For “beginners”...just use your planer/jointer to start squaring your lumber.
For a beginner! ?? But all I have is a hammer, hand saw and a shovel.
Well you can kill, dismember, and bury a person.
wow, commenters ripped him a new one! As a beginner, I have a chop saw and a handheld planer. what was hilarious tho, is the sped up version of a roster crowing, lol!
Good morning from SE Louisiana 7 May 21.
Why all the hate? Everyone complaining it is not a beginner project and the expensive tools and shit. Those are the tools needed to work with wood and the table has a simple design anybody can attempt to make even as a beginner. Use whatever knowledge/ideas you can get out of this video and add your own touch to make it better if you wish, hating on people that are trying to share something good with you is just low, don't do it.
find a way to stop it at 12:08.. it is a twisted sister. the front left foot doesn't touch, like a 1/4" space. sloppy staining too. He is always sanding, like this is sculpting.
Now, when i see a simple wooden table i will more appreciate it. Regard of how complicated it made.
40 seconds of video and 3 expensive machines that a beginner is not able to afford ? Klickbait bullshit.
hàng VN chất lượng cao a!
So after scrolling thru the comments, I see a trend of two types: One bitching abt his equipment and how it's not what a typical beginner would use... and the second bitching abt his choices during the process... Just viewing from my fairly basic woodworking experience, both are true. There's a lot of equipment there that a beginner wouldn't have, and there's a lot of choices made that even an intermediate woodworker would have thought twice about. Classic example of buying your way into a trade without properly learning the fundamentals. But then again, this is RUclips and he got paid by us watching it, even to criticize and notice things we wouldn't do... so kudos. Just use this video as a learning exercise in what not to do, and what tools you REALLY need.
How many of you think that most beginners have a jointer, planer, and table saw laying around.
Very nice || thanks you for sharing
Beginners usually start with a hammer, some nails and a few pieces of wood scraps found from pallets.
Hi Woodworking Guide. I agree with most of the comments on this video. It's a great project, but simple projects for beginners. The ultimate in misrepresentation. Why not just promote it for what it is rather than try to mislead people who see right through it in seconds. Although, presenting it as you did got you 1.1 million views and 436 comments, which is honey to advertisers. Integrity = 0 Money making = 10
Do a lot of beginners have planers and jointers?
Title should say Advanced Beginners :)
Не плохо у китайца получается, с нашей сибирской древисины.
Very nice sir
Am I the only one that thinks it’s crazy he has all these pro tools and used nails in his top, instead of biscuits or pocket holes or simply just a glue up.
Yeah, here we go again. He is using framing lumber, it's not dried, so it will split, shrink, and warp. If he is planning on this being an out side table, the glue he used will fail within a year. This is a complete waist of time. Please don't try and duplicate what he has done here. There are a lot of really good woodworking videos on youtube, please check them out.
Titebond isn’t a good glue for exterior pieces? If not, then what’s the best alternative?
Actually, indoors or outdoors, this will fail. Legs to styles are glued cross grain and the wood will expand and contract in opposite directions, causing greater stress on the joints. The top glued and screwed up is even worse! Never glue the top to the base, as the top will expand and contract the most! Just a few screws with elongated holes in the base to allow for wood movement will help prevent the top from cracking and cupping.
Pine is a soft wood and is more susceptible to movement due to the environment. So, even greater care and design planning is ideal to a better, longer lasting build.
@@jhowe5571 thank you so much I had no idea about any of this
@@jhowe5571 exactly
@@theblackwidow345 if you are interested in glue, I would suggest checking out Wood by Wright how 2. He has a great video series on glue strength.
Great inspiration for my own projects! Thankyou
لن أكون نجارا في المغرب الهجرة إلى أوروبا هي المعادلة الصحيحة في كل هذا الكلام الخرافي
What i noticed is tabletop not in flat..
Could’ve been my top 5 career choice
OMG. The bow in the top at 11:40 is insane. lol. This was one of the most bizarre processes I've ever seen.
Yeah, it looks severely twisted.
The end result does not look like it is bowed when he shows it as he is staining. Almost looks like a different top?
The beginner who has all the professional tools. Just needed to know what to do with them. Just run to Home Depot and spend $4,000 and your ready to go. Beginner check mark ✅.
like from BRAZIL
Looks easy when you have the tools and the space to work 😂
Wish I had all those tools as a beginner
Must be nice to have access to all those expensive tools.
I have them in my garage and I'm not rich. Save and buy them if you want to do woodworking.
Not many beginners have planers and jointers
Nowadays title should sound different like: project for beginners with all the tools presented in the video or with a budget that could afford to buy all the tools😅
Brasil👍👍👍👍🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷
no entiendo como teniendo tan buenas herramientas es tan desprolijo......ya quisiera tener esa canteadora y la ingletadora....algun dia
Very nice 👌
I think I saw this one on sale at Walmart for $99. :-)
For beginners? How many beginners have a big planer like that?
Talk Damn it!
Lol guess this guy never heard of wood movement
The tablet top must not be glued, thats was an error.
@Jio Valdivia,wood grain, yes the orientation wasn't the best and mentioned before me ,table top was glued on.
Maravilhoso trabalho de um Gênio...🇧🇷🇧🇷🇧🇷👍👍👍🤗🤗🤗Parabéns 😷😷😷e Deus abençoe
This is amazing 👍
Someone please send this poor fellow a dow jig, biscuit joiner, domino joiner.......etc.
Beginners ??!!
Yea I’m a beginner and have all that equipment in my shop??!!!!
Oh yea.......I need to build a beginners shop too
😆🤣🤣🤣🤣🤣🤣🤣🤣
stop watching after seeing all the professional tools...this is not for beginners.
A lot of people that make this kind of videos maybe think is fun or a joke to say it's for beginners or maybe they want to show something simple in a overcomplicated way to impress...anyway, it's really deceiving others, specially people that are new to woodworking or are curious on how they could start woodworking. If you really want to show something for beginners then think like a beginner. First, stop using advanced tools, no beginner have those. Woodworking tools for beginners are basically three: a circular saw, a jigsaw and a drill. More than 75% of beginners projects can be done with just those three (along with some basic manual and measuring tools of course). A fourth tool recommended is a sander, with it people can do a comparable result to a planer and achieve better finishes which help a lot.
We are here to encourage others to keep doing and try to do new things, not turn them off.
Thank you so much. Wish you good health
yea i agree with the majority i consider myself an advance beginner i still don't have half the tools you do
Love the creativity
Интересно и не сложно повторить. 👍
What kind of bit that is on the drill press to make that mortise
Yes. I’m curious too. Please let us know.
@@markvasiloff2217 I search it up and it's a mortise chisel bit
@@MrHardcore6 🙏 Thank you. I have never heard of that and have never seen a woodworker use one before. That is a must have in any workshop.
@@markvasiloff2217 true same my first time seeing it
He wasn't using a drill press it was a mortiser with a mortising bit. You would need a mortising attachment to a regular drill press in addition to the mortising bit to perform the same function.
What’s the name of that tool you used to mark the sinter of those boards you put nails in?
It's called a marking gauge. However you can also use another tool called center line scriber which basically does the same and is way cheaper.
I want to know who thinks "beginner" when they see jointers and bandsaws and pipe clamps and some weird dowel system with a drill press .....
I think "beginner" refers to their complete disregard for wood movement. Or safety.
How do you have an electric planar and not have at least a dowel jig for this? Using the nails like this was pretty smart but still
Mallet for Christmas please
What tool was that in the last part of the video where the guy carved or cut the edge of the top?
www.amazon.com/Makita-RP1800-3-1-Plunge-Router/dp/B002MUAMFE/ref=sr_1_62?dchild=1&keywords=makita&qid=1616724900&sr=8-62