Just finished replacing my impeller on my 15 Yamaha 2 stroke.....Thanks for giving the confidence to take that on . Now I thinks I am ready to take on my 115 hp and 9.9 hp Yamahas and replace those impellers ....... You Just saved me a few hundred dollars ..... thanks
@@williamj1527 So nice to know that my video helped you get the job done. They’re virtually all the same job on all engine sizes and brands. Just a few different connection differences. Nice to be able to save a few bucks & do it yourself. Thanks so much for the kind feedback. 😃👍
just finished this replacement in my 15 Yamaha 2 stroke......... your guidance was spot on, the job took me only about 45 minutes thanks to your instruction, cheers mate
adding my own reply due to the fact I should have added that the impellor I replaced had an unknown number of hours on it but that the engine wasn't cooling at full throttle, when I replaced the impellor there were only three of the 6 impellor blades left, they're somewhere in the engine, not sure if that will be a problem.......... if they plug up the outlet water exhaust I guess I'll cross that bridge when I come to it
@@atdougherty Great to hear (or read) that my video was a great help to you Andrew. Thanks for watching and thanks for the positive feedback. Hope that the missing part of the impeller has past through and doesn’t cause any dramas. 😃👍
I'm going to do this next on the exact same motor. good video straight to the point! I also make the same noises when I working as I'm getting older lol. cheers
Very nice size for an outboard engine! it is very good if you can repair such things yourself! Thank you for sharing this video! Big like from Switzerland :-)
I've got the same outboard, haven't used it for a while and tell tale not working. Tell tale and tubing not blocked so I'm sure its the impeller. Thanks for the video - really helpful.
Hello from Michigan, great video! Thanks. I’ve got a 2007 Yahmaha 15 two stroke. Bought it new then, but mostly in storage with only a few hours on it. Tried it today with some fresh gas with Sea Foam. Started up with only 4 pulls. But not peeing. So I’ll get an impeller and have a go at it myself… and not succumb to a hasty trip to the shop. 😊
Thanks for the video! The tip on how to reach the shift rod nuts probably saved me an hour of frustration. Capt. Blackheart Charlie Key West, Conch Republic.
Thanks for the video. Changing the impeller was simple enough. HOWEVER I broke the gear shift connecting rod which was rusted into the coupler nut. Luckily I only lost about 6mm of the upper rod and the threads were not damaged. I replaced the coupler nut and all appears to be functional.
In the service manual for my Yamaha F9.9A it says those bolts for the pumphouse should have thread sealant Loctite 572 on the m. Not Grease. Nice video. Thanks!
Thankyou friend, we have a 15hp Yamaha on our tinny, this may come in handy one day, we hope not, but it may 😘😘 looks successful good flow, no prostate problems there 😳😂🤣😭😭❤
Excellent video but I'm having trouble with removing the gear rod link nut. The bottom lock nut is loosened but the top nut feels like it is seized onto the gear rod. Any ideas? Thanks
Mate your awesome. Thanks for the info. I’m trying to find out why my yamaha 15 won’t pee. I tried to see if it needs unblocking, no, i tried pumping air, no, i unbolted the plate bolted to the side of the motor where the pee cones out from and cleaned it out somewhat but still no. 😢 now I’m going to try what you’ve done here on this video. Wish me luck fingers crossed 🤞
Hey mate great video very helpful! Just wanted to let you know that there is another seal on the impeller housing that should be changed, it’s a large o’ring beween the housing and the s/s plate below. Thanks champ
I hope this is still going strong for you Den. It’s amazing how much money you get charged to replace anything with boats. Before you know it you’ll be doing it for all your mates. I couldn’t re like this video as I ran it through the laptop in day one but forgot to comment so I’ve come back to do it properly. I’m getting old mate 😆😆 Hope your going well and with a bit of luck the fire season slows down for you guys now. 👍
Hi Ryan. Thanks mate. It’s a job I’ve been meaning to get around to for a while and glad I’ve got it out of the way finally. It had been about 4 years since I did it and was over due. I tried to find the yt video I followed last time but it was gone. I thought I may as well make my own vid to help me along next time I need to do it. Now I’ve got my own Yamaha 15 HP service video to easily look back on. Off to QL again tomorrow for a holiday with my wife. How are you mate? How’s the back? I’ve noticed you haven’t made any new vids for a while. I kinda lose interest in making vids at times. I’ve dropped back to maybe one every two or three weeks these days. 😃👍
Good tutorial video. I’ve heritaged a SAIL 15hp outboard motor 4-stroke from 2011 from my dad and have found out that this chinese ob is a Yamaha F15 ‘95 clone. SAIL is surposed to be the same as Parsun and Parsun obs share spareparts with Yamaha. I’m going to change the impeller and I noticed that you only changed the impeller and no gaskets. Is it not nescessary to replace the gasket? I’m asking because when I go to buy the impeller at the Yamaha seller he probably would tell me to change the gaskets and the O-ring. The ob has been stored under correct conditions since 2013 and hasn’t been run since. Best regards Tom / Denmark
Hi Tom. Yes I only changed the impeller because I thought that the gaskets still looked perfectly fine. Great to know that the Parsun OB has comparable parts with the Yamaha. I Spose it wouldn’t hurt to replace the gaskets too. I wouldn’t imagine they’d be that expensive. Good luck with the job and thanks for commenting. 😃
I used my GoPro hero 8 Black for this one mate. I moved it around a bit but clamped it on to a chair and my outboard motor stand to try and cover all angles. Thanks for watching & commenting mate. Much appreciated. 😄👍
Hi Martin. Sorry I’m not sure where you can buy the new linking wire. I was lucky having a marine dealer nearby that specialised in Yamaha outboards. Thanks for the kind feedback mate. Really appreciate it 😃
Thats a tricky question. My outboard doesn't have n hour meter. It had been a few years since I last replaced the impeller, but in all honesty I haven't used the boat as often as I`d planned. At a guess I`d say 100 hours. I think they can deteriorate with use but also over time as well. I`ll be changing the impeller every 2 years from now on. 😄
Have a 2005 50 hp Yamaha 2 stroke that is not putting out water from tale-tell, could impellor be the problem? Have checked the hoses and they are clear as is pick up at bottom of the motor.
Good morning. I recently purchased the same motor and having a little trouble finding parts. Do you have a good link for parts needed for this motor? Thank You!!!
Hi Alan - unfortunately I don’t have any links to suppliers. Not sure where you’re located but I’ve always been lucky going to my local marine shop “Hunts Marine” located in Sydney snd Wollongong. In saying that I’ve only ever purchased a new water pump, spark plugs, fuel filter and gear box oil so nothing major. Sorry I couldn’t be more help.
Hello. I bought the water pump impeller at my local boat shop (Hunts Marine) for under $20. I just told them that I have a 2009 Yamaha 2 stroke and they looked it up on the computer and then picked it out off their shelves. Thanks for watching mate. Glad it was helpful 😃👍
Hope this reaches you a few years late, it seems the throttle bolt is seized, I can manage to get the locking nut away but I can not physically move the other housing but without possibly snapping it! Any advice?
@@TropicalZooms Your words of luck helped! Thank you all sorted, if anyone else here is looking crc and a blow torch does the trick! Impeller looked like a skateboard wheel.. much appreciated for your video
Simple job but my problem the top nut on the gear changer was seized and I snapped it off inside the nut 5 minutes into the job I’m guessing a major repair is in order
@@TropicalZooms Getting the changer out was a lot easier than I expected 6 bolts and disconnect a few cables it will be an easy fix fingers crossed,got the impeller out had lost 2 leaves. Will have back together on Monday after buying the parts, but no mud crabs this weekend. So all is good and enjoy your weekend.
Thanks Andrew. I appreciate your kind feedback mate. Even though I’ve read that these little motors are designed to run on 100:1 I always run at around 75:1. Never had a drama and has always started on first of second pull. 😃👍
you didn't change the oil in the leg, always good to do that same time, check to see if any water getting in gearbox, always use water resistant oil as well
Thanks Bert. I changed the oil in the leg the following day and made it a separate video. See oil leg video here - ruclips.net/video/M4l2F9KuzLU/видео.html
Just finished replacing my impeller on my 15 Yamaha 2 stroke.....Thanks for giving the confidence to take that on . Now I thinks I am ready to take on my 115 hp and 9.9 hp Yamahas and replace those impellers ....... You Just saved me a few hundred dollars ..... thanks
@@williamj1527 So nice to know that my video helped you get the job done. They’re virtually all the same job on all engine sizes and brands. Just a few different connection differences. Nice to be able to save a few bucks & do it yourself.
Thanks so much for the kind feedback. 😃👍
just finished this replacement in my 15 Yamaha 2 stroke......... your guidance was spot on, the job took me only about 45 minutes thanks to your instruction, cheers mate
adding my own reply due to the fact I should have added that the impellor I replaced had an unknown number of hours on it but that the engine wasn't cooling at full throttle, when I replaced the impellor there were only three of the 6 impellor blades left, they're somewhere in the engine, not sure if that will be a problem.......... if they plug up the outlet water exhaust I guess I'll cross that bridge when I come to it
@@atdougherty Great to hear (or read) that my video was a great help to you Andrew. Thanks for watching and thanks for the positive feedback. Hope that the missing part of the impeller has past through and doesn’t cause any dramas. 😃👍
The best video for this project!! Thank you so much for sharing and showing how easy this is.
Thanks so much for the positive feedback. Really appreciate the kind words and glad it helped 😃👍
Thank you sir, a very handy video, exactly what I had to replace. The steps helped me a lot.
Thanks for the positive feedback. Really glad my video helped you get the job done. :-).
Wonderful step-by-step guidance on the pump replacement. Well done, my friend 👍. Big like and full play. Thanks for sharing and enjoy your weekend 😀.
Thanks so much mate. Appreciate your constant support 😃👍
I'm going to do this next on the exact same motor. good video straight to the point! I also make the same noises when I working as I'm getting older lol. cheers
Haha. Thanks mate. Good to know I’m not alone. They’re a great little motor. Had mine for years and never let me down. Glad you liked my vid. 😃👍
Even though I have done this to the 15 HP Johnson we had, watching this was still very Interesting, Thanks for Sharing.
Very nice size for an outboard engine! it is very good if you can repair such things yourself! Thank you for sharing this video! Big like from Switzerland :-)
Thanks again for watching. Always appreciate your support 😃👍
I've got the same outboard, haven't used it for a while and tell tale not working. Tell tale and tubing not blocked so I'm sure its the impeller. Thanks for the video - really helpful.
Glad my video helped mate. Thanks for the positive feedback 😃👍
JUST what I needed. Couldn't figure out how to release the shift linkage on my 2000 9.9. Same design as yours. 1:23 was all I needed!
Glad my video helped you out. Nice to know the little tricks that make this job easy. Thanks for watching & commenting. 😃👍
Thanks. Very handy. Can't believe the pristine condition your engine is in rather than someone that uses theirs 4 times a day in salt. :)
Thanks mate. Glad you liked the bud and found it helpful. I don’t get out often enough in the boat 👍
Hello from Michigan, great video! Thanks. I’ve got a 2007 Yahmaha 15 two stroke. Bought it new then, but mostly in storage with only a few hours on it. Tried it today with some fresh gas with Sea Foam. Started up with only 4 pulls. But not peeing. So I’ll get an impeller and have a go at it myself… and not succumb to a hasty trip to the shop. 😊
Great to hear that you got it started with 4 pulls. They’re great little motors 😃👍
Thanks for the video! The tip on how to reach the shift rod nuts probably saved me an hour of frustration.
Capt. Blackheart Charlie
Key West, Conch Republic.
Glad to read that my video helped you. Just knowing the little tricks is a great time saver. Thanks for the feedback. Much appreciated 😃👍
Thanks for the video. Changing the impeller was simple enough. HOWEVER I broke the gear shift connecting rod which was rusted into the coupler nut. Luckily I only lost about 6mm of the upper rod and the threads were not damaged. I replaced the coupler nut and all appears to be functional.
Great to hear it all eventually went well and nice to know my video helped. Have fun out on the water 😃👍🚤🐟🐋🦈🐳☀️
Great video! Just what I was looking for! Thanks from NZ 👍
Thanks mate. Really appreciate your feedback. 😃👍
Hey mate thank you for your knowledge and effort with the video
Thank you for the kind feedback. Nice to know my video helped 😃👍
Fantastic job!! Thank you,! I just watched it here in Puerto Rico. Now I think I will try. Thanks again.
Thanks so much. I’m thrilled that my video from Australia can help someone in Puerto Rico. Have a great day 😃👍🐟🐟
I was just thinking about this the other day - thanks again!
Yeh. An easy job. Good to get it done 😃👍
Incredible informative video 😀 my friend ! As always great 👍 content! Have a nice week end 🎉!
Thanks so much. You too 😃👍
Bloody well done mate. Helped me heaps!
So good to hear that my video helped mate. Thanks for the kind words. Great little outboards too. 😃👍
This is a great video on how to change this impeller. Hopefully #yamaha see this video and decide to sponsor a free upgrade or trial mate.
Love ur vids mate great guidance
Thanks so much mate. It really gives me a thrill to get great feedback like this. Nice to be able to help people in similar situations. 😃👍
Well done my friend ! It’s important to keep up with the maintenance on your gear ! Thanks for sharing excellent tutorial .
Thanks mate. A job I’ve been meaning to get out of the way for a while. Good to have it all done 😃👍
Excellent video . Thanks for sharing this good information 👍
Thank you. Glad you liked it and hope it helped 🚤😃👍
In the service manual for my Yamaha F9.9A it says those bolts for the pumphouse should have thread sealant Loctite 572 on the m. Not Grease.
Nice video. Thanks!
Thanks mate. I personally think either is fine. I’ve always used the marine grease and never had any problems. 😃👍
Thank you for this excellent video. It's been a long time since I have done one and your video was very helpful. Thank you for making this.
Thanks mate. Glad my video helped you get the job done. Really appreciate the kind words. Means a lot 😃👍
Thankyou friend, we have a 15hp Yamaha on our tinny, this may come in handy one day, we hope not, but it may 😘😘 looks successful good flow, no prostate problems there 😳😂🤣😭😭❤
Hahaha! Thanks for watching & commenting. 😄👍
Thank you for this great tutorial :D
Will come in handy one day 🌞
Thanks mate. Yep. It’s a job I’ve been meaning to do for a while now. Good to get it done. 😃👍
Pretty simple video thanks
Glad you liked it. Hope it helped 😃👍
Well done. Nice timelapse usage now and then ;-) Nice video. Greets !
Thank you. I’m always learning 😃👍
Excellent video but I'm having trouble with removing the gear rod link nut. The bottom lock nut is loosened but the top nut feels like it is seized onto the gear rod. Any ideas? Thanks
@@nOfiKstideas Maybe a spray of WD40?
great tutorial my friend
Thank you. It’s a job I’ve been wanting to do for a while 😃👍
Well presented sir👍👍👍👍😊
Thanks so much. Really appreciate the positive feedback 😃👍
Ohh , i never knew about this but you are good skills that what i saw 😅😅👍
Thank you 😃👍
Great job my dear friend 👍👍👍
Excellent thanks.
@@johnmajewski1065 Glad my vid helped 😃👍
Mate your awesome. Thanks for the info. I’m trying to find out why my yamaha 15 won’t pee. I tried to see if it needs unblocking, no, i tried pumping air, no, i unbolted the plate bolted to the side of the motor where the pee cones out from and cleaned it out somewhat but still no. 😢 now I’m going to try what you’ve done here on this video. Wish me luck fingers crossed 🤞
Good luck mate. Hope you get it all sorted. They really are great little motors.
Also thanks so much for the kind feedback. Means a lot 😃👍
Hey mate great video very helpful! Just wanted to let you know that there is another seal on the impeller housing that should be changed, it’s a large o’ring beween the housing and the s/s plate below. Thanks champ
Thanks mate. Will have to do that one next service. 😃👍
Very nice job ! Thanks
Well done helped heaps
Thanks Ken. Glad it helped you get the job done. 😃👍
Thanks you 👍🏻👍🏻👍🏻
Glad you liked it. Thanks for the 👍👍👍😃
Thanks for sharing.
Hope it helped. Thanks for tuning in 😃👍
I hope this is still going strong for you Den. It’s amazing how much money you get charged to replace anything with boats. Before you know it you’ll be doing it for all your mates.
I couldn’t re like this video as I ran it through the laptop in day one but forgot to comment so I’ve come back to do it properly. I’m getting old mate 😆😆
Hope your going well and with a bit of luck the fire season slows down for you guys now. 👍
Hi Ryan. Thanks mate. It’s a job I’ve been meaning to get around to for a while and glad I’ve got it out of the way finally. It had been about 4 years since I did it and was over due. I tried to find the yt video I followed last time but it was gone. I thought I may as well make my own vid to help me along next time I need to do it. Now I’ve got my own Yamaha 15 HP service video to easily look back on. Off to QL again tomorrow for a holiday with my wife. How are you mate? How’s the back? I’ve noticed you haven’t made any new vids for a while. I kinda lose interest in making vids at times. I’ve dropped back to maybe one every two or three weeks these days. 😃👍
Good tutorial video. I’ve heritaged a SAIL 15hp outboard motor 4-stroke from 2011 from my dad and have found out that this chinese ob is a Yamaha F15 ‘95 clone. SAIL is surposed to be the same as Parsun and Parsun obs share spareparts with Yamaha. I’m going to change the impeller and I noticed that you only changed the impeller and no gaskets. Is it not nescessary to replace the gasket? I’m asking because when I go to buy the impeller at the Yamaha seller he probably would tell me to change the gaskets and the O-ring. The ob has been stored under correct conditions since 2013 and hasn’t been run since.
Best regards
Tom / Denmark
Hi Tom. Yes I only changed the impeller because I thought that the gaskets still looked perfectly fine. Great to know that the Parsun OB has comparable parts with the Yamaha. I Spose it wouldn’t hurt to replace the gaskets too. I wouldn’t imagine they’d be that expensive. Good luck with the job and thanks for commenting. 😃
Great job done Coast Tripz, i also noticed the camera your using (DJI Pocket ?) i have been thinking of buying one, your video was clear and stable.
I used my GoPro hero 8 Black for this one mate. I moved it around a bit but clamped it on to a chair and my outboard motor stand to try and cover all angles. Thanks for watching & commenting mate. Much appreciated. 😄👍
Qthanks Bra ..
Glad you liked it & hoped it helped 😃👍
I’ve got the same motor and the linking wire on the lower unit has broken. Do you know where i buy a replacement one? Thanks great video btw
Hi Martin. Sorry I’m not sure where you can buy the new linking wire. I was lucky having a marine dealer nearby that specialised in Yamaha outboards. Thanks for the kind feedback mate. Really appreciate it 😃
Your the best!!!!
Thanks so much. Nice to know my video helped you. 😃👍
good job! The fins on the old impeller were really bent!
Thanks mate. Yeh. I’m glad I finally got around to getting this job done. 😃👍
Very cool 👍
Thank you 😃👍
Great informed video ..one question how many hours do you estimate were on old empeller? Thanks
Thats a tricky question. My outboard doesn't have n hour meter. It had been a few years since I last replaced the impeller, but in all honesty I haven't used the boat as often as I`d planned. At a guess I`d say 100 hours. I think they can deteriorate with use but also over time as well. I`ll be changing the impeller every 2 years from now on. 😄
Have a 2005 50 hp Yamaha 2 stroke that is not putting out water from tale-tell, could impellor be the problem? Have checked the hoses and they are clear as is pick up at bottom of the motor.
Yes. I would check the impeller. I think that would be the problem if the lines are clear. 😃👍
I remember having no water coming out and slid about 1 metre of whipper snipper cord up through the tel tail which. Learned a small salty blockage.
I think you were supposed to grease up the impeller to ease the cover over the fins of the impeller.
@@vynleshmynle7372 Thanks mate. Will do that next service 😃👍
What did you use as a gasket?
Good morning. I recently purchased the same motor and having a little trouble finding parts. Do you have a good link for parts needed for this motor? Thank You!!!
Hi Alan - unfortunately I don’t have any links to suppliers. Not sure where you’re located but I’ve always been lucky going to my local marine shop “Hunts Marine” located in Sydney snd Wollongong. In saying that I’ve only ever purchased a new water pump, spark plugs, fuel filter and gear box oil so nothing major. Sorry I couldn’t be more help.
@@TropicalZooms I'm in the US. I've reached out directly to Yamaha for assistance as well. Thank you for the fast reply!!
Where did you get the water pump at? Thank you for sharing this video very helpful
Hello. I bought the water pump impeller at my local boat shop (Hunts Marine) for under $20. I just told them that I have a 2009 Yamaha 2 stroke and they looked it up on the computer and then picked it out off their shelves. Thanks for watching mate. Glad it was helpful 😃👍
Hope this reaches you a few years late, it seems the throttle bolt is seized, I can manage to get the locking nut away but I can not physically move the other housing but without possibly snapping it! Any advice?
Jeez that’s no good. Maybe give it a spray of WD40 around the head & leave it for half an hour then retry.
@@TropicalZooms great thank you!
Awesome video and very clear
@@jordanprocter97 Thanks mate. Nice to know my little video helped you. Good luck 😃👍
@@TropicalZooms Your words of luck helped! Thank you all sorted, if anyone else here is looking crc and a blow torch does the trick! Impeller looked like a skateboard wheel..
much appreciated for your video
@@jordanprocter97 Great to hear ( or read) that you got the job done mate. Also nice to know that my video helped. Have fun 😃👍
Simple job but my problem the top nut on the gear changer was seized and I snapped it off inside the nut 5 minutes into the job I’m guessing a major repair is in order
Sorry to hear that. Annoying when these things happen
@@TropicalZooms Getting the changer out was a lot easier than I expected 6 bolts and disconnect a few cables it will be an easy fix fingers crossed,got the impeller out had lost 2 leaves. Will have back together on Monday after buying the parts, but no mud crabs this weekend. So all is good and enjoy your weekend.
@@asnail6550 Thanks mate. Glad it was an easy fix. 😃👍
hey mate nice videos. do you run this 2 stroke at 100:1 or 50:1 mix
Thanks Andrew. I appreciate your kind feedback mate. Even though I’ve read that these little motors are designed to run on 100:1 I always run at around 75:1. Never had a drama and has always started on first of second pull. 😃👍
thanks for the reply. just bought these ones and been reading different mixtures haha this clears it up thought thanks again @@TropicalZooms
@@andrewmichael219 Happy to help. 😃👍
Adakah mesin yamaha 15pk yg seken mau dijual , saya mau beli buat mancing....
I use it for fishing and exploring
Thank you. Glad you liked it. 😃
I have both 15 hp suzuki and yamaha don't know which to keep pls advice
If they’re the same age type ( 2 or 4 stroke) and condition I would keep the Yamaha. I personally think Yamahas make the best outboards.
@@TropicalZooms when I turn the prop by hand on neutral it's not as smooth, is that normal?
@@chauchau95 It doesn’t sound right but I couldn’t be sure. Maybe ask this questions to others as well.
what about new gaskets?
I change them every second time.
you didn't change the oil in the leg, always good to do that same time, check to see if any water getting in gearbox, always use water resistant oil as well
Thanks Bert. I changed the oil in the leg the following day and made it a separate video. See oil leg video here - ruclips.net/video/M4l2F9KuzLU/видео.html
The top numbers are the only ones that you need to order parts
Thanks mate. Good to know. 😃👍🐟🐟
Just remember.... keep the sun behind the camera , don't film into the sun.
Thank you. Good advice 😃👍
Can you please give me the serialnumber? I want to order these decals. Thanks in advance!
YAMAHA
684K
S1075645
G
15FMH
These were all the numbers on the sticker on the side. 😃👍