I just bought an old non-functioning BT L 2000 ($30), and i did a search on youtube, what did i find; Sadik Dan. 1 hour later it is now functioning, apart from a broken return-spring for the handle. Thanks from Sweden! and say hello to my mother in-law(Viola) in Manila if you see that witch...
Very good. I too have a pallet truck with the same problem but sadly don't have the patience or the memory to take so many parts off and remember to put them back in the right place!
check if there is a oil leak,then if there was probably the oil is not sufficient to lift that's why it become weak,I hope I answered your question ☺️☺️☺️
I own a BT Model L 2000 Pallet Jack manufactured in 1993. It pumps up fine and releases fine with no weight on it. With a wooden pallet and 150 lbs it will stay up for about 30-45 Seconds then it drops down to the floor on it’s own. With wooden pallet and 400 lbs on it when lifted it drops right down to the floor in no time. Can someone tell me what the problem is with it. It is full with hydraulic oil like it should be and I tried bleeding it more then once. As I said it pumps up well with no weight on it and releases well it just can’t hold a load for very long and it doesn’t seem to be leaking any fluid. I don’t know much more about it and I don’t see any You Tube videos that shows how to rebuild it. Have no idea where to find a manual to rebuild it. Any help out there is appreciated.
@@daniloeb22 Thanks for responding back. Not sure on my end where to start to take it apart. I see different seal kits sold online for the BT Model L2000. There are 3 kits sold on Amazon. The cheapest $12 US plus Shipping = $19. It consists of 3 Seals and 1 Large O-Ring. I asked the seller if a pump diagram comes with the parts and was just answered with a plain (NO). Then I asked if directions came with the seal kit and this time I received no answer. The more expensive kit comes with way more seals including springs,clips,washers and what have you. It sells for $51 plus shipping for a total of $58. I have no idea which one to order at this point. The smaller kit although more reasonable I am not sure if just replacing the 3 seals and 1 O-Ring will cure the problem.
sir pwedi makahingi ng list ng mga o'rings na ginamit mo? halos lahat ng mga pallet truck namin dito ganyan na ang sakit. meron ba available ng mga spare parts sa Riyadh. salamat sana mareplayan mo ako.
SA Al Iman distributor Dammam kami nag order Ng parts I think Meron Dyan branch SA Riyadh ,wala Naman o ring ako na ginamit U-seal ring at scraper ring seal lng sir!, thanks SA pag watch sorry natagalan pag reply ☺️☺️☺️
@@daniloeb22 sir ganun parin ang hydjack namin, napalitan ko na ng U-seal at scrapper ring. kapagtrial na walang load ok sya, pero kapag i-assemble na kahit walang load kapag ikabit na ang extended fork, nababa ng kusa.
What size is the u seal taken from the piston housing under the spring. Did you just replace that or the complete quick lift piston. I'd just like to order seal, but they only sell it complete with all the piston components.
![Tee Grizzley - Blow for Blow (feat. J. Cole) [Official Video]](http://i.ytimg.com/vi/wNLN5xsx5dc/mqdefault.jpg)
Galing mo sadik marami matutunan sau enjoy lng staysafe
I just bought an old non-functioning BT L 2000 ($30), and i did a search on youtube, what did i find; Sadik Dan.
1 hour later it is now functioning, apart from a broken return-spring for the handle.
Thanks from Sweden! and say hello to my mother in-law(Viola) in Manila if you see that witch...
vart hittade du reservdelar (packning) till din bt 2000 pallyft?
Grabe yang ginagawa mo sadik.ala talaga akong maintindhan, galing mo mangalikot ano, buti pwde kana mgvideo sa work sadik
Chance lng wala Kasi amo sadik🤭👍
Awesome the parts and labour cost more than a new one
my exact tought. But if you can diy then it is worth is i guess
Parts are okay. But the labour costs a ton
I did same. Spent $60 on parts instead of $3k on new one.
BTw they will be bad only after 99 yrs
Very good. I too have a pallet truck with the same problem but sadly don't have the patience or the memory to take so many parts off and remember to put them back in the right place!
Make a video when you dismantle. Easier that way.
Ang. Gling nman ni host mg repair oh
waw ang galing mo naman mag repare.
excellent job!!!
Veri good job
thank you so much for this video it was perfect.
Do all hydraulic pellet stacker need 300ml hydraulic oil?
hard working kuya ingat po always
Ang galing2 nman ni sadik prang Ang hirap mgkalikot nyan sadik kung d mo kabisado iba tlaga pg Pinoy maabilidad ingat sa pagpukpok sadik ung kamay mo
Kowwww kung ako po siguro magagawa ko tlg kalasin yan pero di ko na maibabalik sa tama hehehehe…. Kamusta na po kayo?
Why not clean the dirty parts while you’re in it
Defected. Is it the gasket
How to fix the spring you did not show tha because that spring fixing is little tough
U could have just said get a new one.
Job well done 👍
Is it breakable? How long does a new one usually last? Does the seller promise the quality guarantee time?
Good content bro..
Very good
Beli dimana spare partx Pak,,🙏
mantap bang. jadi itu masalahnya kalo hand palet ato hand lift lemah ya.
What type of hydraulic do used in pallet trolley.
Any hydraulic oil can do thanks for watching my video👍
Klau sudah pasang oil seal baru tak boleh naik knapa ya
Completo o óleo que ela sobe não precisa desmontar não precisa nada só completar o óleo e tá tudo certo eu olho é 68 viu
After watching this I went straight to eBay….time as they say is money.
Nice lod
Dimanakah info sper part bisa saya dapat untuk handlif merek bt. 🙏🙏
Amazing job man!😀😀
Hyd oil Grade??
Good
Ans me if weak lifting then is lowering valve problem?
check if there is a oil leak,then if there was probably the oil is not sufficient to lift that's why it become weak,I hope I answered your question ☺️☺️☺️
if there's a oil leak then probably the oil is not sufficient and become weak lifting,I hope I answered your question thanks☺️
Bro bakit yung LHM230U pump piston namin mahirap tanggalin?
sadik kailangan Alison mo muna un scraper ring then may lock ring un Kaya Di matanggap ang pump piston,Sana na solve ko un tanong mo Sadik 👍
I own a BT Model L 2000 Pallet Jack manufactured in 1993. It pumps up fine and releases fine with no weight on it. With a wooden pallet and 150 lbs it will stay up for about 30-45 Seconds then it drops down to the floor on it’s own. With wooden pallet and 400 lbs on it when lifted it drops right down to the floor in no time. Can someone tell me what the problem is with it. It is full with hydraulic oil like it should be and I tried bleeding it more then once. As I said it pumps up well with no weight on it and releases well it just can’t hold a load for very long and it doesn’t seem to be leaking any fluid. I don’t know much more about it and I don’t see any You Tube videos that shows how to rebuild it. Have no idea where to find a manual to rebuild it. Any help out there is appreciated.
I think the U ring seal in the piston was leaking,try to change it ,thanks for watching
@@daniloeb22 Thanks for responding back. Not sure on my end where to start to take it apart. I see different seal kits sold online for the BT Model L2000. There are 3 kits sold on Amazon. The cheapest $12 US plus Shipping = $19. It consists of 3 Seals and 1 Large O-Ring. I asked the seller if a pump diagram comes with the parts and was just answered with a plain (NO). Then I asked if directions came with the seal kit and this time I received no answer. The more expensive kit comes with way more seals including springs,clips,washers and what have you. It sells for $51 plus shipping for a total of $58. I have no idea which one to order at this point. The smaller kit although more reasonable I am not sure if just replacing the 3 seals and 1 O-Ring will cure the problem.
I have the same problem with mine now. Did you resolve the issue?
Regards don
@@donsmith9846 Nope I couldn’t find out any info anywhere I checked so I wasn’t going to order any kit on the blind.
@@ffas23 Thanks for getting back to me
sir pwedi makahingi ng list ng mga o'rings na ginamit mo? halos lahat ng mga pallet truck namin dito ganyan na ang sakit. meron ba available ng mga spare parts sa Riyadh. salamat sana mareplayan mo ako.
SA Al Iman distributor Dammam kami nag order Ng parts I think Meron Dyan branch SA Riyadh ,wala Naman o ring ako na ginamit U-seal ring at scraper ring seal lng sir!, thanks SA pag watch sorry natagalan pag reply ☺️☺️☺️
@@daniloeb22 sir ganun parin ang hydjack namin, napalitan ko na ng U-seal at scrapper ring. kapagtrial na walang load ok sya, pero kapag i-assemble na kahit walang load kapag ikabit na ang extended fork, nababa ng kusa.
@@rollynsdeocadiz check mo release valve Baka may dumi or naka pull in lever Kaya nababa Ng kusa,
We made hand pallet truck in Vietnam ,contact with me for better prices
Good video but you missed the part where you remove the pallet truck from the mechanism. ?
Where can I order a kit
Ingat sadik parang napakadilikado nyan ginagawa nyo glselvz
What size is the u seal taken from the piston housing under the spring. Did you just replace that or the complete quick lift piston. I'd just like to order seal, but they only sell it complete with all the piston components.
Yan palang na metal yan mabigat na yan iba talaga ang galing ng pinoy magkulikot palang ng mga turnilyo alam na alam talaga ingat host sa work
Great video thanks! I have an electric one to fix. Manual lift though so should be similar.
Sir me i ask.. Iisa lang po ba ang size ng oilseal ng lahat ng pallet truck
may different size po ang U-seal bawat brand Ng hand pallet,thanks for watching my videos po☺️
Quick fix? That was more like a total rebuild. Now i know why the local scrap yard has piles of pallet jacks in it.
Desmontar nada só completa o óleo que vai óleo grosso que não vai vazar mais entendeu que o olho que tá nele botando um óleo grosso 2050 ele nunca
Gud morningm mag kano p paayos ng ganyan pwd po b pa service
SA company po ako nag work,di ko Lang Alam Kung magkano singil sa supplier,thanks for watching my videos it'll big help for my yt channel
@@daniloeb22 ah ok po tnx, kla q po kc nag seservice kau
Excellent job, mas ok pag i on mo yong auto cc while talking sa vid.mo
What's the release level.
San makabili ng parts nyan sir
Ung seals pede I pabricate,since dito ako sa KSA sa supplier Kami nabili Ng spare parts Mahal nga lng,thanks sa pag watch👍
Sadik, ikaw ba yong nsa video?hahahaha Inspire here
Kasama ko un pero parang ganun na Rin😂😂😂
Hahahahaha
great
Thanks for the video
How Can I get that parts???
Wowwww
I have one it lift but didn't go down.
Try to check the release lever maybe it is loose👍thanks for watching 😀
@@daniloeb22 ok
Nice one galing mag repair