Lee pro1000 die Setup
HTML-код
- Опубликовано: 28 авг 2024
- The video shows how to set up the dies on the lee pro 1000. The die set up is the same for all pistol calibers on the pro 1000. This is the first video in the set up series the next video in the series will cover selecting the correct reloading materials, powder disk selection & fine tuning the press
Finally found a video that actually showed step by step I just got the Lee pro 1000 and was battling with it to set up this video is very helpful thanks
Very well explained for us who are new to this press and reloading so good there’s guys out there willing to help us thanks man 👍🇦🇺🇦🇺🇦🇺
Great reloading videos. I just got my Pro 1000 and use your vids all the time for tips, tricks and pointers.
really good quick refresher
Sir thank you for this video! I just set my lee pro 1000 using your video and I also just tried a new batch of 9mm which I call my first borns lol. I need to do some minor adjustment but over all decent target ammo. Again I appreciate you making this video it helped out a lot! 👏🏽👏🏽
My press arrived. I am getting it bolted down. Your videos will certainly be helpful now. Thanks
Thanks . I watched 3 times just to make sure I got it. You make it look easy.
well done, it doesn't take a rocket scientist but good common sense like this fellow. thanks, Max
Thnx that's exactly what I needed to know. Great vids
Very helpful, thanks.
Do you get good crimps with the 3 die set? I have been using the Lee Turret Press which is a 4 hole, so I use the Lee factory crimp die. But I just tried doing 9mm on my new Pro 1000 and the bullet seater/crimp die just does not seem to be working. The bullet is loose in the case. Any way to get a better crimp that you know of?
Fantastic set up video,very clear and informative however, I an having difficulty on the powder/brass expansion stage basicly the 3rd stage were my brass gets kind of stuck and takes amount of force to release and bring it down. Any clue or tips on that?
Great video . Did you ever make a part 2 on fine tuning
Did you make a video on how to set up this same press for a .223 rem if not that would help me out greatly
Greetings from South Africa. I am new to this press and setup and first 9 rounds went well. But now the brass get stuck everytime within the resizing and depriming die....how do I stop this from happening?
the instructions say to screw the full length size die down to where it touches the shell plate, and then lower the shell plate and screw the die in another 1/4 turn...should i do that or what you did
you set me up, thanks
If the pin gets pushed up on stage one how do you push the pin back down
Any advice will help. I just set up my new pro 1000, i have 2 sets of 9mm dies and have tried both powder through dies to stop this issue, with no resolution. problem is my 9mm case is hanging up in the powder through die for sure, causing me to have to pull down with extra force shaking the jell out of the machine. no matter how i adjust the die, to keep a light flare, only way to stop it is to not really get any flare at all and for the record the shell plate is zero'd out fyi. Thank you.
Keith Lvl about the only thing that causes that is the case mouth being flared to much you all you need is a tiny amount of flare.
ok thank you, i'll step it back even further.
Keith Lvl I agree with NodaSheep in that you only need enough of a flare for the bullet to sit on top of the case long enough for it to go into the seating die. My flare is so slight that I don't need to crimp my 9 or 45 after I seat, since the bullet removes the flare as it seats, and I have just a slight hang up on the down stroke. I will say though, that my understanding after talking with more seasoned re-loaders for why it catches and makes a little jolt is to ensure each case receives it's charge without any of it getting hung up in the die. So that jolt helps knock any flakes that may have gotten hung up loose and allows them to fall into the case. Hope this helps.
fisoxlt yup it helps, i appreciate the advice thank you.
Is the Lee powder thru Expander die Universal for all pistol calibers? Been looking for the answer to this question for the past 3 days..
No! they are caliber specific!
Isn't playing, says something went wrong?
can you shoot lead bullets through a Glock?
Good video need a little more lighting.
I use your videos all the time,I downloaded them on my phone for instant reviewing. Here's my question, do you load 380 ACP? If so how do you get the small powder throws to be consistent? I'm using titegroup powder and want 2.8gr throws. The auto disc that come with the press go to .3cc which gets me 3.2gr throws, well over the Max recommended for 100gr bullets. I tried the adjustable charge bar, sucks for small grains but awesome for 223. What's your trick brother.?
I don't reload 380 but titegroup is to dense for that small of a load with the auto disk. I would switch to a lighter powder like power pistol the max load for a 90gn 380 with power pistol is 4.8 Suggested starting load: 4.3 gr 3.7" barrel So that will allow your disk to meter right.
(load data taken for Alliant's 2014 reloading guide)
That's powder is hard to come by here in Colorado Springs. Thanks for the help and Advice though. BTW the case pusher for the 223 is awesome, themes again
Does not cover how to "setup" the press. Does a pretty good job on reloading. How do you set it up?