I'm really glad Red Sea makes these videos because their picture instructons are terrible. I just set the Reef Mat 1200. One of my main problems is when you say "push this button" but you don't say or show where it is! Things would go much smoother with better information. Also, the ReefBeat app works on my iPhone for setting this up but fails at the end on my Android.
I've had a reefmat 1200 going for a couple weeks probably only used about 5 feet of the role got a message saying jammed mat and it unspooled the entire roll of mat in one night any ideas on why that happens thanks in advance
Just in the process of installing my 1200. The inlet hose is too long - I am assuming it is OK to shorten it? If so, what is the best method of cutting it?
Question 1: If you take the filter socket trays and the one panel of glass holding the flow back in the redsea E-260 will take change the water level in the sump - for the return pump section as where my auto top off sensor is located? Question: 2 Can the hose provided with the reef filter 500 kink or get block causing back build of water and cause main over flow to flood the top compartment of the tank? Question:3 As the main drain is connected to the reef hose provided, what happens to the trickle from the emergency drain as that by passes the reef mat filer 500?
1.Yes, you will have to adjust the water level as a result or elevate the ATO float. 2.not likely to happen, but in case it does happen the emergency overflow will start draining the tank and prevent a flood. 3.Your system is a closed system whatever is trickling via the emergency overflow and "escapes" filtration will get filtered next time. It's negligible.
Can someone please tell me where my water level should be if I intend to hang the 1200 model on the side of my sump? The total height of the sump is 21”. I’m having a sump made and the only thing I could find says between the water inlet and up to 1” below the sensor. That doesn’t help me because I do not yet own the product. Thank you for your help!
Hi, the full product's specs are on out website, check out the total height with and without the legs, that would give you a good idea. redseafish.com/smart-hardware/reefmat/tech-specs/
It will be fine if you hang it on the side dont worry about the water level as the inlet pumps water in and as the filter mat clogs it will raise the water level in the unit itself, once it hits the sensor it will drop the water level by turning the roll automatically. Dw red sea i'll do your job.
I’ve got a 125g saltwater reef aquarium that has 2 drain lines what is the best way to run them together to the one line on the roller mat I can’t find a y fitting to use and worried about back pressure using a t fitting
Is the only reason to do it that way to save room on one side? I get a clog roll error when utilizing both ports and the roll is not clogged and I’ve tried everything to troubleshoot and didn’t know if it was volume and velocity of water coming in both ports causing the issue.
@@Redseafish is it possible to do a how-to video on this. Getting back into hobby after 8 years and really do not want to use socks again. If there is a way to connect 2 overflows into this unit, I would like to see it done properly
Hey Neil and RS team. I have the 500 witht he new 300XL G2 aquarium how do I get the filter socks compartment out? I know there removable but not sure how?
Hi, firstly I would like to say this looks like a great product. I have pre-ordered a 1200 but I do not have a Red Sea tank, sorry I am a euro brace kind guy! Anyway, I am just designing my new sump in preparation for the Reef Mat release and wondered what the optimum height for the water is. I'm guessing its just higher than the black inlet but how high does the water need to be if this unit is hanging or should I say how far below is the top of the inlet from the rim that mounts on the tank so I can set my baffles at the right height. I hope that makes sense. Thank you and I can't wait to receive this item.
As l on as your water level is under the sensor the water pressure will push down and out. You have 2 different mounting options, hang on or on feet. Most standard sumps designs will be just fine as long as you don't "drown" it in.
I am building a sump. What are the minimum dimensions to fit the smaller 500? I would like to have just the right size chamber for it. My sump will be 30" x 14". but my biggest question is is there a minimum and maximum water level for the rollers chamber?
@@Redseafish thank you I saw that after posting. But I still haven’t found any recommended water level. Does it need to sit in the water to a certain point or does it not matter
Hi! This is Red Sea reefer from Korea. I'm using reefmat, but every time I activate it, the alarm goes off saying jammed-mat. I changed the filter several times, but it doesn't solve the problem… Let me know
Try aligning the clean roll in the railing making sure it spins the cog on the motor. If that doesn't help contact our support and the can get to the bottom of it. g1.redseafish.com/support/tech-support-inquiry-2021/
The ReefMat only works in seawater. The water level sensor is a conductivity (salinity) meter, designed to easily and reliably detect if the titanium probes are in seawater or air. This system will not detect fresh or brackish water.
Hey Guys. Can you confirm the size of the pipes for the Redsea 625xxl and also confirm the parts list for the plumbing? I have asked my LFS and they couldn't find them. Looking to build a manifold to run a chiller and carbon reactor.
@@Redseafish thanks for the link. I was asking a specific question about the Reefer 625xxl's current plumbing dimensions and parts numbers for that plumbing. Is this something you can help with as my LFS couldn't?
You mentioned you can just slip the flexible tubing that comes with the reefmat right onto the return pipe. In the video you slide it on but then no mention of securing it that way. How would I secure it using that method?
You add some of the provided sealant and sure it with a tie (not provided). Using a reusable zip tie would make it easy to take off if needed. I’m using a plastic clamp with screws, so it’s easy to remove
My ReefMat has never advanced automatically. The sensor seems to ignore the rising water level. I had received a replacement water level sensor under warrantee from Red Sea, but it did not help at all. Now Red Sea product support has gone silent. I guess they have no solution either.
That's sound like an installation error. Make sure you're app is on auto advance. Regardless, it's highly unlikely for the support team to not reply within 24h. If you have a ticket submitted please check your spam\trash it sometimes get there. You can send us a ticket# and we'll look into it.
He's a fast little guy, if we can capture him and pack him with, then he'll arrive with your order. Otherwise the RM is pretty much ready to go and the installation is not that big of a deal if you ask the thousands of hobbyists who already got and installed it. Visit our FB group to see what they have to say. facebook.com/groups/817257271620591/
Always relaxing to see you explaining things, Neil 😉
Better than a beer in front of the TV
That’s absolutely massive!
Wait till you see them in action!! You'll love that.
I'm really glad Red Sea makes these videos because their picture instructons are terrible. I just set the Reef Mat 1200. One of my main problems is when you say "push this button" but you don't say or show where it is! Things would go much smoother with better information. Also, the ReefBeat app works on my iPhone for setting this up but fails at the end on my Android.
Thank you for your input. We'll take that into consideration for our upcoming products.
You need to get a dc return pump to complete your app line of gadgets !!
Yes please add a DC return pump! And a sump that is “ReefMat ready” so no filter socks…
Oh yea... We hear ya... ;)
@@Redseafish and a monitoring device, PH, temp, salinity, ORP pretty please 🙏 ❤️ I’d love to monitor these values in the 👑 Reefbeat app
Need a video on how to modify the sump to accept them too… or is there a v4 sump coming?
It's in the works.
Video or sump or both? Getting an XL300 in a week or two…. V4 sump would have been nice.
I've had a reefmat 1200 going for a couple weeks probably only used about 5 feet of the role got a message saying jammed mat and it unspooled the entire roll of mat in one night any ideas on why that happens thanks in advance
Please contact our support, they can assist you. It's going to be hard to diagnose it over the YT comment section. Thanks.
Just in the process of installing my 1200. The inlet hose is too long - I am assuming it is OK to shorten it? If so, what is the best method of cutting it?
Yes, cut it to fit with a sharp knife\box cutter.
Question 1: If you take the filter socket trays and the one panel of glass holding the flow back in the redsea E-260 will take change the water level in the sump - for the return pump section as where my auto top off sensor is located?
Question: 2 Can the hose provided with the reef filter 500 kink or get block causing back build of water and cause main over flow to flood the top compartment of the tank?
Question:3 As the main drain is connected to the reef hose provided, what happens to the trickle from the emergency drain as that by passes the reef mat filer 500?
1.Yes, you will have to adjust the water level as a result or elevate the ATO float.
2.not likely to happen, but in case it does happen the emergency overflow will start draining the tank and prevent a flood.
3.Your system is a closed system whatever is trickling via the emergency overflow and "escapes" filtration will get filtered next time. It's negligible.
Can someone please tell me where my water level should be if I intend to hang the 1200 model on the side of my sump? The total height of the sump is 21”. I’m having a sump made and the only thing I could find says between the water inlet and up to 1” below the sensor. That doesn’t help me because I do not yet own the product. Thank you for your help!
Hi, the full product's specs are on out website, check out the total height with and without the legs, that would give you a good idea.
redseafish.com/smart-hardware/reefmat/tech-specs/
It will be fine if you hang it on the side dont worry about the water level as the inlet pumps water in and as the filter mat clogs it will raise the water level in the unit itself, once it hits the sensor it will drop the water level by turning the roll automatically.
Dw red sea i'll do your job.
When will it available in Australia?
We will have an update soon. Please register to our newsletter to be the 1st to know.
www.redseafish.com/red-sea-newsletter/
I’ve got a 125g saltwater reef aquarium that has 2 drain lines what is the best way to run them together to the one line on the roller mat I can’t find a y fitting to use and worried about back pressure using a t fitting
You can buy an extra connector and feed from both sides. Reach out to our support to figure out the parts and how to get them.
Can you utilize both ports and have water coming in from both directions?
Yes you can, you will need to get some parts first. It's recommended to merge before the inlet and then use 1 inlet to save the room on one side.
Is the only reason to do it that way to save room on one side? I get a clog roll error when utilizing both ports and the roll is not clogged and I’ve tried everything to troubleshoot and didn’t know if it was volume and velocity of water coming in both ports causing the issue.
@@Redseafish is it possible to do a how-to video on this. Getting back into hobby after 8 years and really do not want to use socks again. If there is a way to connect 2 overflows into this unit, I would like to see it done properly
I have a reefer 170 g2 plus. What do i need to do to make the reefmat 500 fit? Its says its reefmat ready
Remove the sock holder and refuge divider.
WOW，it looks amazing.
Thanks
Hey Neil and RS team. I have the 500 witht he new 300XL G2 aquarium how do I get the filter socks compartment out? I know there removable but not sure how?
You can remove the sock compartment by pulling it out, on the G2, no tools needed.
I can confirm the 1200 is the monster we all needed 👌🏼 absolute wonder to watch in operation 🤩
Thank you.
i actually expected to see an install in an actual reefer setup like the famous rsm 250
We will upload a demo soon. There's a lot going on in our video studio.... ;)
What’s everyone putting in the media basket? Carbon?
That's what we use. (reef spec carbon)
When are these available to buy in the U.S.?
Spring 2022.
Spring 2022 can consist of a 3 month window, any close date?
Will plastic having issue with Ozone?
Ozon will damage it.
Hi
Need a video to modify reefer350 v3 sump to fit this unit please
We will upload a demo soon. There's a lot going on in our video studio.... ;)
Hi, firstly I would like to say this looks like a great product. I have pre-ordered a 1200 but I do not have a Red Sea tank, sorry I am a euro brace kind guy! Anyway, I am just designing my new sump in preparation for the Reef Mat release and wondered what the optimum height for the water is. I'm guessing its just higher than the black inlet but how high does the water need to be if this unit is hanging or should I say how far below is the top of the inlet from the rim that mounts on the tank so I can set my baffles at the right height. I hope that makes sense. Thank you and I can't wait to receive this item.
As l on as your water level is under the sensor the water pressure will push down and out. You have 2 different mounting options, hang on or on feet. Most standard sumps designs will be just fine as long as you don't "drown" it in.
That is so fancy!!! Ain’t that fancy y’all!!!! WOW 🤩 Do you still need a skimmer?
Yes you still need a skimmer.
I am building a sump. What are the minimum dimensions to fit the smaller 500? I would like to have just the right size chamber for it. My sump will be 30" x 14". but my biggest question is is there a minimum and maximum water level for the rollers chamber?
You have the exact measurements here, take into account the inlet pipe as well.
g1.redseafish.com/hardware/reefmat/
@@Redseafish thank you I saw that after posting. But I still haven’t found any recommended water level. Does it need to sit in the water to a certain point or does it not matter
For less noise the inlet should be submerged under water. It will fill and empty as the fleece moves.
Hi! This is Red Sea reefer from Korea. I'm using reefmat, but every time I activate it, the alarm goes off saying jammed-mat. I changed the filter several times, but it doesn't solve the problem… Let me know
Try aligning the clean roll in the railing making sure it spins the cog on the motor. If that doesn't help contact our support and the can get to the bottom of it.
g1.redseafish.com/support/tech-support-inquiry-2021/
I can use reefmat in freshwater?
The ReefMat only works in seawater. The water level sensor is a conductivity (salinity) meter, designed to easily and reliably detect if the titanium probes are in seawater or air. This system will not detect fresh or brackish water.
@@Redseafish, is a sensor for freshwater planned?
So here’s the kicker. I have the 1200 mat, with absolutely no way to install this on 40mm drain pipe. What’s the story here and how do I go about it?
Merci pour la présentation, ou positionnez vous un tel filtre dans un XL425 ? Merci de votre réponse
You have the mounting and modification options here:
www.redseafish.com/fr/hardware/reefmat/
Would love a new sump for my reefer 350 for the 500 mat
You'll love it
@@Redseafish can’t wait 👍
Is this product compatible with other brand tanks ?
It should be. In most standard sumps there's room for equipment. check out the specs to see if your sump can fit it.
Hey Guys. Can you confirm the size of the pipes for the Redsea 625xxl and also confirm the parts list for the plumbing? I have asked my LFS and they couldn't find them. Looking to build a manifold to run a chiller and carbon reactor.
We have it all here, including the modification options:
www.redseafish.com/hardware/reefmat/
@@Redseafish thanks for the link. I was asking a specific question about the Reefer 625xxl's current plumbing dimensions and parts numbers for that plumbing. Is this something you can help with as my LFS couldn't?
Sorry about that. Pleas contact tech support they can provide you with that info:
www.redseafish.com/support/tech-support-inquiry-2021/
You mentioned you can just slip the flexible tubing that comes with the reefmat right onto the return pipe. In the video you slide it on but then no mention of securing it that way. How would I secure it using that method?
You add some of the provided sealant and sure it with a tie (not provided). Using a reusable zip tie would make it easy to take off if needed.
I’m using a plastic clamp with screws, so it’s easy to remove
Will this fit in the Reefer 170?
Check out the mounting options here:
www.redseafish.com/hardware/reefmat/installation-options/
My ReefMat has never advanced automatically. The sensor seems to ignore the rising water level. I had received a replacement water level sensor under warrantee from Red Sea, but it did not help at all. Now Red Sea product support has gone silent. I guess they have no solution either.
That's sound like an installation error. Make sure you're app is on auto advance. Regardless, it's highly unlikely for the support team to not reply within 24h. If you have a ticket submitted please check your spam\trash it sometimes get there.
You can send us a ticket# and we'll look into it.
@@Redseafish still no reply. And it surely is not an installation error. ticket number is 61124.
@@Redseafish so... Did you look into it? 24 hours you say, but support hasn't even responded to me in 5 days now.
Спасибо за обзор, выглядит изумительно 👍👍👍
Your welcome.
Does Sheldon Cooper from Big Bang Theory come with the device to help you put it together and take it apart each time? OY.
He's a fast little guy, if we can capture him and pack him with, then he'll arrive with your order. Otherwise the RM is pretty much ready to go and the installation is not that big of a deal if you ask the thousands of hobbyists who already got and installed it. Visit our FB group to see what they have to say.
facebook.com/groups/817257271620591/
Today i bought and installed the 1200 version but the sensor does not work!
Any ideas anyone?
Hi, the best idea is to reach out to tech support. They'll sort it out in no-time.
Do fleece rollers filter out bacteria?
No.
Red sea support uk for this unit, is there a contact number?
You can get it at any Deale shop. You can reach out to tech support here if needed:
www.redseafish.com/support/tech-support-inquiry-2021/
So where’s the tutorial on how to cut to bits your Red Sea sump you’ve just bought to make it fit?
In the works. Will be loaded soon.
Does not fit my 750XXL return pipe. Appears to be 40mm instead of the 32mm.
Yes, there are fittings to connect it to the downpipe.
Cost?
Please reach out to your local RS dealer for pricing.
Your own carbon is too small for that container. It will fall through the holes. Don't tell me we have to use bags...
You need to use the mesh bag that comes with the Reef Spec Carbon. The larger holes allow placement of different media for ideal flow.
Oh comment c'est chiant à monter.... Vendez le monté !
What glue (or primer/cement) do you recommend for gluing the universal connector to the PVC pipe?
There is such a huge selection of PVC glue brands. We can't recommend one over the other.
@@Redseafish I ended up using some solvent cement which was approved for drinking water.
Awesome.
The sensor on mine never worked and the motor is unbearably loud and wakes up the whole house. Not worth the price and I expect more from red sea.
Ever consider you might have a faulty or wrongly installed item?
So many people swear by these, me included.