Rebot min, ALE15 is overtravel which should come up when the unit powers up the first time. ALE05 is regeneration error and ALE07 is overspeed. These are both dynamic alarms that should not happen upon power up. Chapter 7 of the manual covers troubleshooting: cdn.automationdirect.com/static/manuals/sureservomanual/ch7.pdf Your application questions may be best answered by contacting our FREE, award winning technical support team: community.automationdirect.com/s/contactsupport
@@automationdirect Thank you. Now this has been fixed, but error 18 appeared in the new driver. It was tested on the other axles X and Z and it has the same defect. The Y axle was tested on another driver and it works perfectly.
@@rebotmind2396 I'm sorry that you are having this issue. It would be best to contact our technical support group. community.automationdirect.com/s/contactsupport Thanks!
+Fernando Davila Yes, there is a link to the FREE SureServo Pro software download on this page, as well as full details about the associated programming cable(s): www.automationdirect.com/adc/Overview/Catalog/Motion_Control/Servo_Systems/I-z-O_Interface_-a-_Communications_-a-_Software Please understand that the software (and programming cable) are NOT required - you can do all the drive setup via the keypad (as shown in this series of videos). However, some users may find that the software is more convenient, especially if they have to set a large number of parameters, or if they are configuring a large number of SureServo drives.
This video shows how to position the servo. To control the speed go to page 1-17 of the user manual: cdn.automationdirect.com/static/manuals/sureservomanual/sureservomanual.pdf It shows you step by step how to do that.
Not sure I am understanding your question. You would probably be best served calling into Tech support for this detailed of support. Please call 1-800-633-0405
Hi Florent, SureServo has a variety of ways to establish home position. The home sequence can be initiated by a Digital Input or thru coms - (by defining a DI as a Virtual Digital Input (see parameters P2-10, P3-08, and P4-07). The Homing Mode is defined in parameter P1-47
Hi Florent, You have to re-home the original SureServo if control power is removed. But remember that control power and motor power are different inputs, so if wired correctly the drive should retain its position unless the entire control panel has power removed. FYI: We have a new servo system we are planning to release this fall with a battery backup so it never looses positioning. Be sure to subscribe to our RUclips channel so you will be notified when that is available.
Hi Victor, for technical questions like this, please contact our free award winning tech support. They are setup to give you the most efficient and quickest support. Phone: 1-800-633-0405 Email: www.automationdirect.com/adc/Form/User/TechInquiry Support: support.automationdirect.com/ Please let us know if you have any other questions! Thanks, AutomationDirect
Thanks for the comment Prasanta Adhikary! We will add it to the production list. If you need help with this now, I would suggest, calling in to the Support Team. 1-800-633-0405.
Thank you for watching! For technical questions like this, please contact our free award winning tech support. They are setup to give you the most efficient and quickest support. Phone: 1-800-633-0405 Email: www.automationdirect.com/adc/Form/User/TechInquiry Support: support.automationdirect.com/ Thanks, AutomationDirect
@Mohamed Ali Massadi, That is an alarm with drive fault code of 09, which is excessive deviation. That code can be seen on page 4-11 of the user manual, cdn.automationdirect.com/static/manuals/sureservomanual/sureservomanual.pdf. A more detailed explanation can be seen on page 7-4 and 7-7.
Thanks! Did you know we have over 1100 tutorial videos like it at: www.automationdirect.com/videos (random search) www.automationdirect.com/cookbook (by subject)
@ Teexx. Anngliee if you are looking to reset to the factory default, you can find the information in the user manual that is available for download on our website here: cdn.automationdirect.com/static/manuals/sureservomanual/sureservomanual.pdf Page 1-12.
Great Education
+Tony N Thanks for watching - we are happy we could help!
Please know the error 5, 7 and 15 appears on the screen as soon as the power is connected
Rebot min, ALE15 is overtravel which should come up when the unit powers up the first time. ALE05 is regeneration error and ALE07 is overspeed. These are both dynamic alarms that should not happen upon power up. Chapter 7 of the manual covers troubleshooting: cdn.automationdirect.com/static/manuals/sureservomanual/ch7.pdf Your application questions may be best answered by contacting our FREE, award winning technical support team: community.automationdirect.com/s/contactsupport
@@automationdirect Thank you. Now this has been fixed, but error 18 appeared in the new driver. It was tested on the other axles X and Z and it has the same defect. The Y axle was tested on another driver and it works perfectly.
@@rebotmind2396 I'm sorry that you are having this issue. It would be best to contact our technical support group. community.automationdirect.com/s/contactsupport
Thanks!
question :first ,thank you ,,,is this servo drive work well with do more H2-dme ?i mean in modbus mode,,,thx
Hi Salah, Yes, any Do-more enabled PLC would be a great choice for communicating with the Sure Servo system.
I'd like to know , if there is a software to set up these servo drives?
+Fernando Davila
Yes, there is a link to the FREE SureServo Pro software download on this page, as well as full details about the associated programming cable(s):
www.automationdirect.com/adc/Overview/Catalog/Motion_Control/Servo_Systems/I-z-O_Interface_-a-_Communications_-a-_Software
Please understand that the software (and programming cable) are NOT required - you can do all the drive setup via the keypad (as shown in this series of videos). However, some users may find that the software is more convenient, especially if they have to set a large number of parameters, or if they are configuring a large number of SureServo drives.
i have Panasonic MCDHT3520E driver, i want to change direction and speed how it doing by front panel please help me
Hi Thillina, Unfortunately we only support the Sure Servo Brand of Drive. Please contact Panasonic for questions about that drive.
I did this but wanted to control the speed of the servo motor on this connection? Can i please
This video shows how to position the servo. To control the speed go to page 1-17 of the user manual:
cdn.automationdirect.com/static/manuals/sureservomanual/sureservomanual.pdf
It shows you step by step how to do that.
@@automationdirect
Thank U my frinde
You can send your number to communicate on WhatsApp
MS S3 YAKO SERVO
ERROR 002
PLZ TELL ME PROBLEM
I would Advise contacting YAKOTEC for this problem. We do not sell the Yako Servo line.
Thanks Chip, We'd use software just to back up all parameters and make easier a modification.
can you make a communication with plc to put values from the logic of plc?
@Monkeydjarm, thanks for the request. I will add this request to our production list. Thanks
Thank you. So can you answer the question? I need to put values from my plc to the driver
Not sure I am understanding your question. You would probably be best served calling into Tech support for this detailed of support. Please call 1-800-633-0405
Thoughts and prayers to the company that is entrusting monkeydjarm with engineering.
How do you define a zero reference on the engine?
Hi Florent,
SureServo has a variety of ways to establish home position. The home sequence can be initiated by a Digital Input or thru coms - (by defining a DI as a Virtual Digital Input (see parameters P2-10, P3-08, and P4-07). The Homing Mode is defined in parameter P1-47
Thanks but is it possible not to lose the engine position without making homing after a shutdown?
Hi Florent,
You have to re-home the original SureServo if control power is removed. But remember that control power and motor power are different inputs, so if wired correctly the drive should retain its position unless the entire control panel has power removed.
FYI: We have a new servo system we are planning to release this fall with a battery backup so it never looses positioning. Be sure to subscribe to our RUclips channel so you will be notified when that is available.
Ok its possible to remove only motor power via Digital Input or by configuring the drive ? Thank you
@@florentdethoor6565 Yes.
as I can connect one of these to an interface for a cnc machine?
the interface is USB cnc controller, which they are the CN1 connector pins?
Hi Victor, for technical questions like this, please contact our free award winning tech support. They are setup to give you the most efficient and quickest support.
Phone: 1-800-633-0405
Email: www.automationdirect.com/adc/Form/User/TechInquiry
Support: support.automationdirect.com/
Please let us know if you have any other questions! Thanks, AutomationDirect
can you create a video for AC servo motor & encoder " 0" position settings.
Thanks for the comment Prasanta Adhikary! We will add it to the production list. If you need help with this now, I would suggest, calling in to the Support Team. 1-800-633-0405.
how to connect input supply ,what is meant by RST L1,L2
Thank you for watching! For technical questions like this, please contact our free award winning tech support. They are setup to give you the most efficient and quickest support.
Phone: 1-800-633-0405
Email: www.automationdirect.com/adc/Form/User/TechInquiry
Support: support.automationdirect.com/
Thanks, AutomationDirect
Control card on l1 and l2
Sir ji mere pas ek Toshiba ki servo drive h muje us Ko software se jok mod me chalana h plz plz plz plz help my sir
Hi Ajay, Unfortunately, AutomationDirect doesn't support Toshiba Servo Drives so we can't help you with that one.
Sir plz send me your mobile number ??????
@@ajayo185 Hi Ajay,
Please contact our free technical support at 1-800-633-0405
@@automationdirect ye no to sir sewa me nahi ha
@@automationdirect sir ji Toshiba ki servo drive h our me us Ko jog mode me chalana chata hu
What L1.01
I'm not sure what you are asking. Can you provide more details?
?sir ;i have alarm009,how i can solve it
@Mohamed Ali Massadi, That is an alarm with drive fault code of 09, which is excessive deviation. That code can be seen on page 4-11 of the user manual, cdn.automationdirect.com/static/manuals/sureservomanual/sureservomanual.pdf. A more detailed explanation can be seen on page 7-4 and 7-7.
thank you for explanation
You're welcome! Did you know we have over 1000 videos just like it located here: www.automationdirect.com/videos
Thank you for your great effort
Thanks! Did you know we have over 1100 tutorial videos like it at:
www.automationdirect.com/videos (random search)
www.automationdirect.com/cookbook (by subject)
شكرا على ترجمة الفديو ب اللغه العربي
("
Thanks for translating the video into Arabic") - You are welcome!
thank you for the information
You are very welcome, Mohamed.
thank you sir.
Reset located
@ Teexx. Anngliee if you are looking to reset to the factory default, you can find the information in the user manual that is available for download on our website here: cdn.automationdirect.com/static/manuals/sureservomanual/sureservomanual.pdf Page 1-12.
gud one...