9 tools I regret not buying sooner
HTML-код
- Опубликовано: 14 май 2024
- Big thanks to Ethos for sponsoring this video! You can get a personalized insurance quote in 10 minutes for as low as $10/mo here: ethos-life.sjv.io/MWA
Here are 9 tools I wish I'd bought sooner! New woodworkers don't have to regret it anymore!
✅️ TOOLS AND SUPPLIES IN THIS VIDEO:
Chamfer & Reamer Tool - tsoproducts.com/bench-dogs/ac...
Power-Loc Bench Connectors - tsoproducts.com/bench-dogs/ts...
Chamfer Dogs - tsoproducts.com/bench-dogs/ts...
Universal Fence Clamps - tsoproducts.com/clamping-work...
Portable Drill Guide - tsoproducts.com/jigs-fixtures...
Straight Edge - amzn.to/3QsL6Tz
Enjoywood Pocket Hole Jig Pro - amzn.to/3Q6k2YJ
Enjoywood Pocket Hole Jig (cheaper version) - amzn.to/45LbA6R
Estwing Rubber Mallet - amzn.to/401x6TX
Multifunction Scribing Tool - amzn.to/3S5RNMo
Small Parts Organizer Bin - amzn.to/45GH7XQ
StudBuddy - amzn.to/490q9GI
Dymo Label Maker - amzn.to/3u3jHyv
📽️ WHAT TO WATCH NEXT
Organize any Workspace - • 11 Simple Ways to Orga...
Cheap Tools Every Woodworker Should Have - • Why doesn't every wood...
How to Build Cabinets - • How to Build Wall Cabi...
✅️ PROJECT PLANS:
The Whole Enchilada Plan Bundle (Save 65%) - mwawoodworks.com/product/the-...
✅️ HOW TO SUPPORT MY CHANNEL
Join my Patreon community: patreon.com/MWAWoodworks
Get Project Plans: bit.ly/download-project-plans
Get some MWA Woodworks Logo Merch: www.mwa.keyapparelstore.com/
SUBSCRIBE : ruclips.net/user/mwawoodworks?...
✅️ LIST OF THE TOOLS I USE IN MY SHOP : bit.ly/tools-i-use
*Disclaimer - As an Amazon Associate I earn from qualifying purchases
✅️ Other Affiliate Partners
Bits and Bits Co. - 10% OFF using code MWA10 - bit.ly/48Pw5Cq
TSO Products - tsoproducts.com/?ref=MWAWW
Taylor Toolworks - lddy.no/1gngh
✅️ MWA WOODWORKS ON SOCIAL
Instagram: / mwawoodworks
Facebook: mwawoodworks
Pinterest: / mwawoodworks
---------------------------------------------------------------------------------------------------------------------------------------------
⏱️ Chapters
00:00 I'd have done it different
00:22 Don't buy a drill press!
03:10 Not your granny's pocket hole jig
05:51 Game changing chamfer reamer tool
10:31 Clamps that do more
12:09 Bendy is better!
13:34 I got your stud RIGHT HERE
15:18 Organize your chaos
17:14 Multitaskers ROCK
18:34 My kingdom for a mallet!
#diyprojects#woodworkingproject#howto 
Хобби
As a guy that’s been doing woodwork literally his entire life I’m 65 now, OK well for 45 years now. Those locking table dogs are the absolute best thing that I’ve seen. I’ve got most the other stuff covered but yeah I had no idea about those and that little tool to put the chamfered top on the hole. Plus that other pocket jig. I’m definitely ordering one of those. Great video buddy appreciate it.
When my daughter was 6 or 7, my wife let her pick out my Christmas gift at a dollar store. She chose a similar mallet, which 25 years later, I still used regularly. She always gets a chuckle when she sees that old mallet in my bag when I'm working on something at her house.
I bought a $1 magnet extension to reach lost nuts. That has paid for itself many times.
Been watching a lot of these type of videos from builders lately. And I just gotta say, I'm liking this dude the best. No fluff, just straight to the point and the why behind it.
This is maybe the best "tools advice" video I have seen. Affordable, kind of obscure, but REALLY useful tools. THanks!!!
Thanks 👍
I agree with your recommendation on that mallet. I saw you or someone on another channel using it, and thought I'd pick one up and try. I now use it *all the time* in my assembly -- it's my go-to mallet. It has just the right heft, and unlike my wooden mallet or dead-blow hammer, doesn't leave any marks. Best of all, it was less than $20.
👍
You can always choke up on it to do chisel work too. I cleaned out a knothole with mine and a 1/4" chisel pretty easily.
I just use scrap piece of wood to lay over the fine piece and than I can use anything to kick it. Maybe easier to use soft mallet but I would be worried about soft woods like spruce if I hit it with harder plastic side or also soft side of the mallet. It's like everything wants to leave marks on spruce.. Too soft for anything that needs nice finish.
@@matejcermak😂🎉
Thanks don’t usually get value out of these types of videos but your has been the exception! Worth the watch.
We had a commercial shop, at my work. We had bins of odd hardware, all mixed together. I bought a bunch of Cookie Sheets all the same size. Made a Rack out of scrap Plywood, to slide the Cookie Sheets into. Had a Sheet for each of the following. Wood screws, Sheet Metal Screws, Machine Screws, Machine Bolts, Nuts, Washers and the final one for Lock-washers.
👍
Thanks for the heads up on the tools. I could use most of them. Some now and some to replace others when they need to be. I certainly appreciate it! 😊😊😊
Awesome 👍
I bought a similar mallet when I was 19. Now, 58 years later, I have replaced the heads several times and it is still my most used tool after the impact driver. Used for everything from driving stakes to engine work. It even comes in handy on the wood lathe. I now have a large collection of hammers but other than driving nails and ball peen work, this is virtually the only hammer I use.
Excellent tips. By the way, the idea of using a ruler for drawing curved lines is very good and has in fact been known for a long time. Such tools were called splines (which has also made its way into the name of parametric curves in modern computer programs, e.g. Bézier splines) and were used in design. Curves determined in this way followed the path of energy minimization, which was of great significance in the design of components, for example, automobile bodies. It's great that you're reminding us of these not necessarily commonly known methods today.
🙌
This roundup is fanatic! I’ll definitely be using your links this upcoming Black Friday weekend.
🙌
I used to have a Port-a-Line drill guide. That is the one tool that I regret letting go of when I was forced to down-size. I tried to find one years ago, and couldn't find anything like it. I'm glad to see someone is making them again.
Drill guides are also perfect for people who can't have a shop at all.
Ujk and rockler use the same manufacturer...they are just ok, better options exist...wp...
"Would you start a furniture build without a plan" you clearly don't know how many bad decisions I make
Lmao..I also said “yes” out loud to myself at that part of the video
The tools are great, but it’s the artist who uses them to produce the best results. Nice work!
Great presentation - lots of useful tools! I saved this video for when I redo/reorganize my garage.
Great tips! Love the pocket hole jig platform!
Yeah I have so many ideas for upcoming jigs now!
Dude that mallet… I have one too (not estwing tho), and I use it ALL the time. Great for hold-fasts, chisels, persuading metal things… everything. Love it.
High value information in this video. Thank you for sharing your personal findings, much of it can align with my small garage shop.
One of the best reviews of tools you should have that I have seen. Loved the pocket hole tool. I want one.
I'm more of a putterer than a wood worker but I find the better tools I have the better my projects come out!
First video of yours I have seen and I love your Kregg alternative! Gave me lots of ideas. Thanks.
Those are all some nice tips but that #1 is super sweet and a compact option 😳 I will definitely be selling my drill press and buying one of those so I can have more room after 🎉 Thanks for the info ✌️
Another fantastic video. Been home for months with a broken leg and your videos are well done and very informative. Plus, it’s a good place to see the newest tools in use.
Thanks for watching and for the kind words! Hope you heal up soon!
Dude your Jig for your Jig chefs kiss so perfect!
There are a couple of these I need in my life. I work in a small residential cabinet shop and I'm always looking for clever tools/solutions. Using the table saw fence as the router fence adjustment is perfect. We have a big cast iron sawstop table saw in a 10x10 table. But our rarely used router table is trash. Using the extra space, with the good tablesaw fence to adjust the router fence will make me use a router table again. And I'm making a magnetic stud finder today. I already have the materials so thanks for that one too. Also the drill guide was what came to mind first. We don't have a drill press but I have a cheap plastic guide that I just found and started using. Having parallel holes, especially on hardware jigs is so important. Especially when you have to flip the jig and then start using a bigger bit to get everything straight. Think ill upgrade that too.
Finally someone with practical info. Been woodworking for 38 yrs and this is very cool stuff. Thank you
Thank you for this video. I’m brand new and have no idea where to start! Now I’m replacing the kregg on my wishlist with the one you recommended ❤
Love these videos! Coming from both experience, and even in that best tools I've used this year on some of the projects. For us novices, and those who don't have or haven't thought to use those tools others have, learning from one another is invaluable (and cost effective!). =)
Finally! A buying guide for everyone...not just the super-rich! Thanks a lot. I'm subscribing.
🙌
What, you don’t like guides like “The 10 Festool tools that you absolutely must own if you ever want to do any woodworking”? :)
@@gf2e LOL! Well put!!!
Wow. All your tools are spotlessly clean. Almost like they never get used. 😊
This…sounds like an insult lmao
mom always said I clean up real nice 😁
There are people who religiously clean everything after each use. I’m not one of those but there are people like that 😂
Very informative and enjoying to watch, thank you so much 👍👍
Such good content, what a great amount of knowledge and experience compacted in such a great video. Thank you sir!
🙏
Cool video! Those are some really useful tools. I really like the portable drill guide! I may pick one up this weekend.
Great video
As a cabinet installer myself i found that the
"CH Hanson 03040 Magnetic Stud Finder" is the best out there and much more compact
Great suggestions. I have been wood working for a while now and I don't have most of those useful tools that you have pointed out but suspect I will be getting some of them in the near future.
🙌
Unbelievable new kit, blown away.
When/if my Kreg jig wears out or breaks I'm buying one like you showed! That's a very nicely made jig. I just made two new mallets to get an in-between weight for various chiseling work. I have a dead blow hammer for assembly with non-marring faces. Works pretty well. Glad you mentioned MAKING a mallet - I've never bought one (after >40 years woodworking).
Great video. I love it when people share their lessons they've learned through experience!
Most excellent advice all around. Thank you so much. Insurance tip is excellent.
Lol thanks!
Definitely adding quite a few of these to my list! I framed for years so I love the feel and weight of my framing hammer, with a smooth face, and use a block of the same species of wood I am building with. Seems to never mar the surface and then I don’t have more things laying on my work surface hah
Awesome!
@@MWAWoodworks and then after I say that, I just saw your hammer on sale at the store so I got one to try haha
Great suggestions, Matt! I have an unusual interest in different kinds of hammers and mallets, so I definitely understand where you are coming from! 😂 As far as the drill guide and fence clamps go, I have the Rockler versions of them and I have to agree they are wonderful tools. That drill guide really saved my bacon a few times before I got my CNC! Looking forward to the next video. - Joe
Thanks Joe 😀
Awesome ! Great video thanks! Stud buddy is great! But remember drywallers don't always put the nails or screws in the center of the stud! Most of the time though!
35+ years ago Craftsman sold a similar drill guide. It didn’t have the angle adjust, but it did allow the rods to extend below the base. That way you slip it over the edge of a board, rotate it until the rods rest on the top/bottom of the board…perfectly centered dowel holes. I still have mine.
If I had waited 30 seconds…the screw in pins do the trick. Nice souped up version of an old idea.
👍
I think that my Drill guide just turned 40 and keeps on going. Bored a LOT of holes with it and set more than a few dowels.
I use magnets to find screws, and that tool looks like an improvement. However, be aware that where edges of drywall meet, the screws will be offset to the left and right at the joints. Also be aware, guys may not sink them in pairs, so that they are next to each other, and they may not center them on the studs, particularly if the framers did not space the studs perfectly.
I've used those little super magnets dangling from a 6" strip of blue tape.
Lots of tools to make my woodwork much easier. Excellent Tutorial.😊😊😊
Thanks 👍
I bought a drill guide from Sears for my dad, Christmas late 1970's. A crude version, but very similar.
When a hole needed to be drilled at exactly 90 degrees, there was no doubt about it.
I still have it.
[edit] Just a tip... you can hot glue (or other means) a fastener to the face of each bin showing what it holds.
If you don't want to hot glue, a couple of very small holes and a bit of tie wire will do the same job. Also makes it easier to remove that item if you want to reallocate that bin to something else.
Excellent tips and tools, many of which I didn’t know existed! 😊👍
🙌
Thanks man. I got lots of great ideas from this video.
Awesome 👍
The second you mentioned the portable drill guide like 7 pieces clicked into place for me! I was like “of course that’s a thing, how did I never consider that to be a thing before??”
Texted the gf immediately to update the Christmas list 😂
Great info. Thanks for sharing, Matt.
Thanks Rich!
Well done, Thank you!
YOU ARE F***N AWESOME! Great information! Keep it up. I definitely subscribed! 😊
Thanks Brian! 🙌
I don’t know your name mate but I have to say that you have just become probably my favourite workshop/woodwork guy on RUclips. What a wonderful, neat and tidy workshop. I wish I had similar. Thank you so much for posting. I have just subscribed - you’re a keeper!! Best regards from the Giant’s Causeway coast of Northern Ireland. 😄👍☘️
I have a couple of rubber/plastic mallets, but there's often no better option than simply holding some scrap wood over the workpiece and hitting that.
Concerning screw storage, I have a toolbox full of clear plastic business card boxes, which have various screws in them. They're all labelled and easily available.
Love your drill driver holders❤
🙌
So many options. Yes!
Love love love anything from ujk. Still have yet to use the parf system I purchased
Me too but my next build will be using it, I think
Great video. Thank you.
A + exceptional professional presentation. Thank you.
👍
I am more impressed with the jig you made than the tools themselves. Nice video.
🤣🤣
That is the most awesome JIGGIDY JIG !!!!
I’m a big fan of the Estwing mallet. Wish I bought it sooner 👍
Thank you so much.
Will be buying the flexible straight edge for the same reason I think it's odd to not get a drill press... non-flat surfaces. I guess they're not that common in woodworking but definitely something I have frequently.
For the stud buddy... brilliant. I recently independently had that realization when I had some leftover neodymium magnets. Way more reliable than a typical studfinder.
Yep for sure
Downside of the studbuddy approach is it doesn't guarantee that you find the center of the stud
@@scotth5503 true. However, I think finding a few screws on the same stud will be more reliable than a stud finder… or just just a combination of the two.
I rarely need to worry about finding the exact center of the stud. If I am I probably am removing the drywall and attaching right to the studs like on a floating shelf.
a couple I made note of two I have "shop built" items that work as well or better than what shown. Nails & screws I made a box with bottom filled box with short lengths of 4" PVC as "holders" "Countrytime" lemonade (which I drank a lot of as a contractor) containers just fit into the PVC. once container is empty, washed and snip off spout on chopsaw. place desired fastener into container, write contents on lid with marker (no need for high ?? label printer) affix lid & place containers in order of size & type into "rings" and hang on wall
2nd. A simple narrow, thin strip of wood and a length of string. Cut bow style notches on sides at one end, tie loop in one end of string, when "arch" is needed affix loop over end into notches, bend wood to desired radius and wrap loose end of string around several times. tied loop gives you quick release with easy repeat.-
Both good ideas!
Lixie makes the best mallet imo. The flooring version has their two softest heads which are so soft you can hit pine HARD and it wont dent, but still puts a lot of energy into the piece.
Thanks for the recommendation. I've not heard of that!
The Harbor Freight dead blow hammers work great for assembly. Have a small one for cabinets and a large one for timber framing.
Great job! Subscribed.
Thanks 😊
I just bought the kreg 720 pro for $129 on clearance at Lowe’s. I set it up on a 30”x 18” piece of plywood. Complete game changer!!!
nice
I like this video and it shows great potential for tools, on the mallet, try a dead blow rubber hammer like the ICON 16oz soft face dead blow hammer. Great video.
Great tool tips.
One thing to consider on the Stud Buddy, if you are at a Drywall Butt Joint the screw will be in the 3/4 half of the 1.5 inch stud. So it won't be in the center.
True! but I'm not sure I care? Why do I need to be exactly in the center?
@MWAWoodworks for pictures, it's probably no big deal, but if it is a big TV wall mount, then only catching a half of the stud with a 3/8 lag may be problematic.
Regardless, it's a good tool for finding a stud.
Thanks for turning me on to several interesting tools
For small/loose part and especially fastener storage, I strongly recommend the briefcase style tools
They work like the drawer or bin style storage tools, but you can carry them anywhere and know exactly what you have
I started replacing all my drawers and bins about five years ago, and ... they make VERY POPULAR Christmas gifts
I love those for doing work on the road. But when I'm in my shop I like being able to grab just the bin I need and then put it back when I'm done.
The handle of my Craftsman hammer has a thick rubber cap on the end, which is perfect for tapping parts into place, without needing to drag around another tool.
My thermal printer is the best thing I’ve bought in years practically. That along with some small bags or Mylar bags and variety of label sizes… it’s organized stuff so well. Whenever I get extra parts for an item, pop a label on it so quickly or use it to make instructions and pop it on.. I use it several times a day. lol
Is funny to see the drill storage I designed over 10 year ago and uploaded to sketch up also here.
Oh, BTW, about the mallet... I made a small one with a softer wood (which I'm not sure what it was exactly, perhaps even some kind of pine) and I use it exactly for that! Works amazingly!
I thought about making a mallet from heart pine and testing it out on plywood. Maybe a future video idea!
@MWAWoodworks Oh, absolutely! 😊
Mine is really simple. It's around 2" x 2" x around 3 1/2"... And I used a 3/4" dowel as the handle. That's all. 😊
I works nicely until it eventually breaks :(. I did one out of pine with inner holes filled with lead to give it weight. It was perfect until it broke.
@@CemKalyoncu Everything breaks eventually, unfortunately.
@@MCsCreationsDefinitely, but this broke within a few months. Maybe I shouldn't have used it on hardwood.
Thank You for this video. I appreciate all this information. Learned a lot. I would also ask if you could mention where tools are manufactured as part of the description. I ALWAYS seek out the American made tools. Especially if its made of metal. Ill keep watching and subscribe.
You can clamp the drill guide to a larger piece of wood, and clamp or attach the wood to your target, increasing your options such as the distance from the edge whilst clamping.
Yep that's true. If you pre drill your hole in the "larger" piece it can also help with tear out. But it does limit the depth of cut you can get so id use maybe 1/2" ply or thinner if possible
Nice shop !
Nice work - thanks
You're welcome
excellent video ... thanks
Thanks for the great tips. I'm buying a Stud Buddy ASAP because I'm still traumatized from years ago when I drilled and then screwed *four* holes into the bathroom drain pipe for shelf supports. The electronic stud finder indicated it was a perfect 1.5" stud width, so despite my usual careful and skeptical nature, I went with it. *sniffs* Hmm... what's that smell? 😂
🤣🤣🤣
Thank you.
I’ve been seeing your video on my timeline since you posted it. And wondered every time what the heck is that attached to the drill!? And why do I need it.
Now I know 😅
That fake kreg jig-jig is inspired! 😍👏👏👏
I love those guys that make tools out of wood
Nice video, although I have all of the mallets I prefer a dead blow for assembly.
Dead blows are nice I just prefer a mallet that doesn't sound like maracas when I use them 😂
You really should look at batching out those pocket hole jigs on the CNC and selling them. I’d buy one right now!
It's crossed my mind 😁
@@MWAWoodworks update us if you do. I don’t have a CNC and don’t plan on getting one just for that. Haha. But I’ll buy one and I’m sure others would also.
I'll have to figure out how much shipping something that big would be 🤔
Or at least make a shoping list with all the parts (easier to ship, to). Any one of us can, and want to make that MDFboard, with your drawings. I would love to order all your stuff throu you, so figure out som way we can order by simply clicking. Its a jungle out there if you want to find the right parts and I want to make all the clever guids, but it stops there as I can’t find the right parts. Please tell me when you are done with your “easy order”. OK? 😊.
Joa in Sweden.
I'd totally buy one. Unfortunately don't have a CNC to make one myself.
5:00 "What do you call it when you build a jig for your jig?"
JIGCEPTION!
"In both milimiters and standard measurements"... That made me chuckle.
I usually say millimeters and normal LOL
Milimeter is the Standard.
😬😅😅😀😂
Nice list and good video
Hey thanks brother good to hear from you!
I absolutely love my oscillating tool
Which one do you have?
Ya buddy. They are the shit. Once you've had one, you can't ever go back to not having one. lol
I totally need a stud finder.
Apropos mallets, plastic faced dead blow mallets, in different weights, every time! The multipurpose scribing tool looked interesting too.
🙌
good recommendations
Great list!
Thanks!
Gettin jiggy with it😂
Nice reference now I have Will Smith in my head 🤣🤣
Some great tool/accessory finds here, thanks very much for sharing!
You're most welcome
BRILLIANCE ON DISPLAY!!!
Ha! Thanks 👍
I promised myself no more new tools until I organize my shop. But I like the drill guide! Another broken promise.
I appreciate your honesty 😂
Franklin stud finder works great and it has never lead me astray