Hello sir thank you very much for your video regarding the exhaust pipe that BMW 740! . I have a BMW 2019 740i I’ve bought it seen August but 2 weeks ago I found out that one of my exhaust pipe no smoke was coming out of it , I was worried about that, I call the dealer where I’ve bought my car and I describe what I’ve noticed about 2 weeks now . The told me that my car was not supposed to do that unless I’m on the highway and the actuator will open . I was worried and I said I just don’t believe it . I went on RUclips I saw your video I went back to my car and looked at through the exhaust pipe then I saw the actuator . Now I have no worries anymore. Thank very much for your video. It’s really helpful 👍🏻👍🏻👍🏻👍🏻👍🏻
Man... This was great. Its the first video showing "WHERE" the vacuum hoses are located in the trunk and how to get to them! PROPS for that! Will this work to stop the Exhaust rattling? In my diag I hear this rattling so I used a small rod to push in the pipe on the Actuator with the car running and it stopped. This tells me I most likely have a vacuum leak. So again, might this b a good work-around for that problem? THANKS
Your car definitely has the correct valve for this to work. Not to sure where it’s located on your model. Do a little research & if no luck let me know & I’ll see what I can find.
OK so... I tested this and immediately realised this just permanently closes the valve... Supplying constant vacuum to the valve. In order to work just remove the side vacuum line to the controller and leave the bottom one.
@@rekairinger7700 Unplug the left one that runs directly to the valve there's no need to cap the line to the valve because the whole point is that atmospheric pressure is needed in the line to hold it open. The Bottom vacuum line comes directly from the source of the vacuum in the engine bay. Quick test is when you plug this one you can here the atmospheric pressure entering back in. So just leave this one connected.
Most BMWs have this controller but you should read my comment. I tried this and instead of bridging the two vacuum line. All you you need to do remove the left Vaccum line on the controller that is directly connected to the valve. So the atmospheric pressure overcomes the dome pressure in the actuator that controllers the valve. No engine lights super. Simple to try! This video was just a waste of time.
Check the back of the car and look for a valve and read my most recent comment because it's simpler to do than this. This will actually permanently shut the valve doing it this way.
OK so... I've commented this before but people need to realise this won't work. I tested this and immediately realised this just permanently closes the valve... Constant vacuum to the valve In order to work just remove the side vacuum line to the controller and leave the bottom one.
Firstly thank you for this helpful video and I’ve just tried it on my 2010 750Li. The drive is much better now, however my exhaust sound hasn’t changed much and don’t have any of that nice bang sound. Any suggestions?
This mod permanently closes the exhaust valve. The controller allows an Vaccum leak at certain RPM to operate the valved system. In order to work leave the Source Vaccum line on the bottom and remove the Left Vaccum like line that runs straight to the Vavle the atmospheric pressure holds it open. No engine light. Simply
OK so... I've commented this before. I tested this and immediately realised this just permanently closes the valve... Constant vacuum to the valve In order to work just remove the side vacuum line to the controller and leave the bottom one.
Hey I have a 2011 750 f02 quick question did you notice a difference with driving experience related to back pressure? Correct me if I’m wrong but I thought those Vaccum lines work alongside the turbo wastegate? Any lag or loss of torque due to back pressure?
Well all this mod is doing is permanently closing the valve. I tried it, Easy way to verify is look down the exhaust tip. This runs a direct vacuum source straight to the valve. (Not ideal). Just remove the left Vaccum line to the controller and it actually works!
Hello, I have a '12 f02 with the mufflers chopped. I want it a little bit louder without being super loud (i.e charger scat pack). Would this do the trick?
No 😲 go to a local muffler shop have them do a resonator delete and weld a 3inch pipe all the way back with some nice tips bammm mine sounds like a 🐉🐲 dragon
@@MrHustleSwag go CATLESS HEADERS AND resonator and muffler delete and put in a vibrant resonator and dual tips then get a ECU tune from revmatch motorsports stage 2 tune 💯💪💪💯🎇🎇🎇🎇🎇💯💯💯💯💯💯🎇🎇🎇🎇🎇🎇 you wont regret it brotha !!!!!
@@MrHustleSwag so im currently building a super sleeper E39 530i 01' next is coilovers and then a m50 manifold swap then a supercharger kit but just go to my channel got some clips of the exhaust sound from when I fist got the car and put catless headers in and complete straight piped then when i put in the vibrant resonator youll then the stage 2 tune
I know how it feels to be desperate for attention. I've tried everything, too. Recently scored a cherry Toyota Corolla - 2003. Straight-piped and totally pimped it. The babes have taken note. And, quite a few dudes. Hoping to sew some wild oats. I'll keep the community posted on any success.
OK so... I tested this and immediately realised this just permanently closes the valve... Constant vacuum to the valve In order to work just remove the side vacuum line to the controller and leave the bottom one.
Firstly check the boot or (truck) Secondly I've commented this before but anyway. I tested this and immediately realised this just permanently closes the valve... Constant vacuum to the valve In order to work just remove the side vacuum line to the controller and leave the bottom one.
![Blox Fruits Dragon Rework Update [Full Stream]](http://i.ytimg.com/vi/EqDAp8udhm0/mqdefault.jpg)
Great video, this seems like a really good option.
Do you know where the actuator is located on a 2022 M340i?
Thanks in advance!
Hello sir thank you very much for your video regarding the exhaust pipe that BMW 740! . I have a BMW 2019 740i I’ve bought it seen August but 2 weeks ago I found out that one of my exhaust pipe no smoke was coming out of it , I was worried about that, I call the dealer where I’ve bought my car and I describe what I’ve noticed about 2 weeks now . The told me that my car was not supposed to do that unless I’m on the highway and the actuator will open . I was worried and I said I just don’t believe it . I went on RUclips I saw your video I went back to my car and looked at through the exhaust pipe then I saw the actuator . Now I have no worries anymore. Thank very much for your video. It’s really helpful 👍🏻👍🏻👍🏻👍🏻👍🏻
Awesome glad this helped!
Hi, could you help me locate my vacuum hose? I have a 2013 X5 xdrive35i (N55 engine).
Did you figure it out?
I have a 2012 bmw x5 xdrive 35i
hello how can i find the vacum line in x5m 2021 legit
Hi looks a good hack. Getting a new 2024 X5 50e shortly and would this hack also enhance the sound and where would the hoses be. Thanks
does the car need to be on or off when doing this? thank you
Preferably off to not cause any vacuum faults
Where is my actuator on my 2022 BMW X2 Sport? Thx
Thanks for this hack. I have a F86 X6M, where is the actuator?
Also, where is the resonator video? Couldn’t find it on your feed. Thanks again
Hi
We’re I find the actuator for a X5 ‘23 and we’re to find the white small tube you use on the video to connect the two tubes
Thanks for your help
2021 BMW X5 40I. Does it have a valve? Thanks
2023 540i where would mine be located
2017 540i x-drive. Where to find it? Thank you!
Hello man. how it work on prius With changing Exhaust FUll system?
Man... This was great. Its the first video showing "WHERE" the vacuum hoses are located in the trunk and how to get to them! PROPS for that! Will this work to stop the Exhaust rattling? In my diag I hear this rattling so I used a small rod to push in the pipe on the Actuator with the car running and it stopped. This tells me I most likely have a vacuum leak. So again, might this b a good work-around for that problem? THANKS
I have a 2018 x5. Where would I find the vavles?
can you explain why adding that t keeps the valves not just open but fully open?
2015 75li should be in the same location ? and would it be better to get the wireless fob one?
Hi mate BMW F26 x4 35d msport.
does this increase horsepower at all
hi buddy how r u , i have a x5m 2013 e70 engine 4.4 bi turbo motor S63 my sound is little , helpme! please
Will do I’ll find out this weekend how you can get some great sound out of it.
Hi, Im looking for the vacuum hoses on my X6 e71 35i ?
Thanks for the information and video. I have a 2014 640i. Could you let me know what I need to do for my car to get the sound we "need"!!
Your car definitely has the correct valve for this to work. Not to sure where it’s located on your model. Do a little research & if no luck let me know & I’ll see what I can find.
OK so...
I tested this and immediately realised this just permanently closes the valve... Supplying constant vacuum to the valve.
In order to work just remove the side vacuum line to the controller and leave the bottom one.
Hello, you removed the hose facing the side and capped it with something or left it? And kept the bottom one plugged into the controller?
@@rekairinger7700 Unplug the left one that runs directly to the valve there's no need to cap the line to the valve because the whole point is that atmospheric pressure is needed in the line to hold it open.
The Bottom vacuum line comes directly from the source of the vacuum in the engine bay. Quick test is when you plug this one you can here the atmospheric pressure entering back in. So just leave this one connected.
@@HARDMAN999 so leave bottom connected and the side one just hanging loose?
Where can I buy the piece?
I have 2017 x4 m40i and can’t seem to locate the exhaust vac hose to do this mod any help is greatly appreciated
Most BMWs have this controller but you should read my comment.
I tried this and instead of bridging the two vacuum line.
All you you need to do remove the left Vaccum line on the controller that is directly connected to the valve. So the atmospheric pressure overcomes the dome pressure in the actuator that controllers the valve.
No engine lights super.
Simple to try!
This video was just a waste of time.
I have a 2011 x5 50i am I able to do this mod bossman
I have a 2014 550 xi it’s too quiet and I want to drill a few holes on the muffler till I get a muffler delete should I do it ?
Where's the vacuum pump on the 2018bnw x1 ?
Hey buddy have you thought of installing an exhaust System on your highlander? If not do you know of one that can be bolt on?
Thank you.
Not on a Highlander, it’s a V6 they just wouldn’t sound good. It would make it sound like those annoying Honda’s with those big mufflers.
I have a 2014 bmw x6 xdrive35i would like to know where my is located
Does this work on a 650i
Check the back of the car and look for a valve and read my most recent comment because it's simpler to do than this. This will actually permanently shut the valve doing it this way.
Can this be done with a bmw x5. 2015
Thanks for this video
Tuo ting they are work for I4 X5 2022
I have a 2013 BMW X6 35i where is mine? Thanks
Location on the 2018 bmw x1 ?!?
Does it work for an bmw 220i from 2021?
Hi we‘rr i find the actuator for a x6m 2018?
Would you know where to find it on a 2023 540?
Hi I have a 2022 430i. What diameter/measurement barb fitting do I need?
Did you find it?
Where is the actuator on a 2015 BMW 650 I grand Coupe X Drive
I’m truly asking for help been trying to figure out where it is on my 2014 428i but can’t find it please help. All I want is more sound.
Unfortunately this only works on the BMWs with the vacuum controlled valve your cars has a electronic controlled one.
2016 BMW X1 would it be located same area
I have a 2021 X6 m50i how do I make it loader
I need help, awesome video by the way! I have 2019 M850i, where would my hose be located? Same place as yours. Thanks in advance 💯
Hey can you tell me where and vacuum line on a 2011 BMW X5 35ixdrive?
I’ll check tomorrow & find out for you
WHere is this actuator for a 2019 xi ??
Heyy! Is this process possible for a 2020 228i bmw gran coupe? I checked in the trunk and it was quite difficult to find. I might not have it, idk?
u have it
hey man great video ! i have a 2003 325i would this work for me?
No
Hey mate, Have you looked at your exhaust to see if it has a Valve on the backbox/exhaust tips?
What are these small barb things exactly called?
Vacuum tubing connectors. Automotive based
@@JJBanuelos thanks mate and the diameter?
OK so... I've commented this before but people need to realise this won't work.
I tested this and immediately realised this just permanently closes the valve... Constant vacuum to the valve
In order to work just remove the side vacuum line to the controller and leave the bottom one.
I have bmw 740 li 2008 model
Is it poss in that car
Would this work on a 2014 428i
Is this possible on 750 li 2006? And how can I get that bypass
Read my most recent comment because it's actually alot simpler than this!
Hi, would this work for a 2022 x5? Thanks!
No, this will not. I have 2021 X5, and ours have a electronic actuator system.
Firstly thank you for this helpful video and I’ve just tried it on my 2010 750Li. The drive is much better now, however my exhaust sound hasn’t changed much and don’t have any of that nice bang sound. Any suggestions?
My suggestion would be to eliminate some of the cars resonators it has. That really cuts down the noise you want.
The drive is much better “now” but the exhaust sound hasn’t changed?… 😂 This doesn’t improve the way your car drives, it changes the exhaust note. 🙄
This mod permanently closes the exhaust valve.
The controller allows an Vaccum leak at certain RPM to operate the valved system.
In order to work leave the Source Vaccum line on the bottom and remove the Left Vaccum like line that runs straight to the Vavle the atmospheric pressure holds it open.
No engine light.
Simply
I have a question I have a 2013 bmw 640i m sport Grand coupe does my ride even have value flaps I want a more aggressive sound
HELP!!!!
What engine size do you have?
I have a 2013 BMW X1 with twin turbo. Is this possible for my car???
Should be the same setup.
@@JJBanuelos thank you so much
@@Dasha-hv3zu did you do this on your car? If so what were the results? I have the same car and am thinking about doing it
I got a button for that on my center console. 😊
Will this work on a 2013 320i?
Possibly not sure on the setup on those
OK so... I've commented this before.
I tested this and immediately realised this just permanently closes the valve... Constant vacuum to the valve
In order to work just remove the side vacuum line to the controller and leave the bottom one.
I have a 2014 4 series 428i where is mine?
timing chain
I don’t see valves. That means I can’t do it at all?
Its posible for 540i 2018?
Possibly if it has this same setup which it might
DANG! In that left well in my trunk I got all electronics for the NAV and amp...
BNW???
Hey I have a 2011 750 f02 quick question did you notice a difference with driving experience related to back pressure? Correct me if I’m wrong but I thought those Vaccum lines work alongside the turbo wastegate? Any lag or loss of torque due to back pressure?
Well all this mod is doing is permanently closing the valve.
I tried it, Easy way to verify is look down the exhaust tip.
This runs a direct vacuum source straight to the valve.
(Not ideal).
Just remove the left Vaccum line to the controller and it actually works!
I Have a BWM X5 2014
2022 X7 M50i
Hello, I have a '12 f02 with the mufflers chopped. I want it a little bit louder without being super loud (i.e charger scat pack). Would this do the trick?
No 😲 go to a local muffler shop have them do a resonator delete and weld a 3inch pipe all the way back with some nice tips bammm mine sounds like a 🐉🐲 dragon
Only cost me 160$ for the delete and pipe and 97 for tips I got nice dual burnt tips welded on
@@fckyoutoobe can you post a video? I have a f01 13 B7 and can’t decide what to do
@@MrHustleSwag go CATLESS HEADERS AND resonator and muffler delete and put in a vibrant resonator and dual tips then get a ECU tune from revmatch motorsports stage 2 tune 💯💪💪💯🎇🎇🎇🎇🎇💯💯💯💯💯💯🎇🎇🎇🎇🎇🎇 you wont regret it brotha !!!!!
@@MrHustleSwag so im currently building a super sleeper E39 530i 01' next is coilovers and then a m50 manifold swap then a supercharger kit but just go to my channel got some clips of the exhaust sound from when I fist got the car and put catless headers in and complete straight piped then when i put in the vibrant resonator youll then the stage 2 tune
Hey I have BMW X5 2004 3.oi
Hi there I got a bmw X3
Could you please help me out
What year?
Where is this on 2025 bmw x5 m 40
I know how it feels to be desperate for attention. I've tried everything, too.
Recently scored a cherry Toyota Corolla - 2003. Straight-piped and totally pimped it.
The babes have taken note. And, quite a few dudes.
Hoping to sew some wild oats. I'll keep the community posted on any success.
😁
That seemed like it did nothing 😂
I literally heard no difference 🤔
in person and in the car you will for sure hear a difference in depth
Nice definition of "any". Clickbait = thumbs down.
Will this work on a 2021 320i
I have a 2010 bmw x1 e84, where is my actuator located?
Will this work on a 2007 bmw 328i?
OK so...
I tested this and immediately realised this just permanently closes the valve... Constant vacuum to the valve
In order to work just remove the side vacuum line to the controller and leave the bottom one.
I commented this on most posts.
If you find my original comment and like it it'd be great for people in the future to find this information. Cheers
@@HARDMAN999 Hi so do you have any pictures of where the vacuum line is.
I don't think this will work on mine because I don"t think i have a valve in the muffler.
@@AL-xk8mj It's in the left side of my boot/truck for my 330i
Will this work on 2017 x4 m40i
If it has this similar setup then yes it should work the same way
@@JJBanuelos I looked in the trunk driver side and the only thing that is there is the stereo amp
Can I do this with e92 M3?
Does it work on a 650i ???
Should if it has the exhaust valves similar to these
@@JJBanuelos 👍👍
Just want to inform you when I tried this I realised that it's just allowing permanent vaccum to the exhaust which actually fully closes the valve.
Hello where would it be on a 2021 BMW X5 i40 XDrive?
Not sure but if it has the same actuators on the muffler it should work the same way
2014 535i will this work? Thanks
Would it work on a 2022 x6 40I
It’s possible on 420i Engine N20??
Firstly check the boot or (truck)
Secondly I've commented this before but anyway.
I tested this and immediately realised this just permanently closes the valve... Constant vacuum to the valve
In order to work just remove the side vacuum line to the controller and leave the bottom one.
Will this work on a 2020 X7 40i?
You know I’m not sure I’ll have to double check for you
Will this work on 2011 BMW X3
Pretty sure it will, I can look it up for you
Will this work on a 2013 750i xdrive?
Totally
Will this work on my bmw 523i e60 2005?
Is it the same for the 23 X3?