The ULTIMATE guide to 9.5" Chevy Drum Brakes
HTML-код
- Опубликовано: 30 сен 2024
- Learn every step of how to change drum brakes. This drum brake how-to guide is for standard Chevy drum brakes. It also applies to many other vehicles from trucks to hot rods that use the exact same 9.5 inch drum setup. This video is intended to help save you time and money when you're doing your own DIY brake job. Below is a list of parts and part numbers used in this video. Thanks for watching!
Parking Brake lever- ACDelco 179-2012 *Fits left side only* amzn.to/2KrdLJv
Equalizer Bar- Dorman HELP! 21129 amzn.to/3mKNOSh
Equal Bar Springs- Carlson Quality Brake Parts H1341-2 amzn.to/3aIkPMr
Return Springs-Wagner H323 Drum Brake Return Spring Kit amzn.to/38Cmoc2
Wheel Cylinder Pins- Dorman HW1418 amzn.to/34HfctW
Small Parts Kit- ACDelco 18K740 Brake Shoe Hold Down Kit amzn.to/2WKt56n
Slack Adjuster kit- ACDelco 18K14 *Fits left side only* amzn.to/3rB0krd
Wheel Cylinder- Centric Parts 134.62027 *Fits left side only* amzn.to/3nOwZqV
Brake Shoes- Newtek Automotive NB246 amzn.to/3poX5Rs
Adjuster springs- Duralst H450 Includes 1 left and 1 right spring
What about the e-brake attachment????
There is a piece missing. It's a flat plate that fits on the top pin to hold the shoes flat. The springs hold it in place. The flat plate insures the shoes move out and back properly.
Mines we’re missing it to get in the morning
Thanks for commenting I would have completely forgotten about it
Just noticed mine after installing everything. Bummer on the omission on this video, would have been a great video otherwise.
good to know, as it helps to know when you DON"T know how to do this yet! Thanks Daniel.
@@breakroommanager1 I forget that plate nearly every single time.
Okay, when you speed it up like you have done, it makes it a lot more difficult to actually see what you're doing.
No I don't see anything he FF past that is important. Great video but I'm not sure the front shoe can be put on with an axle installed.the equalizer won't clear the cylinder and the axle. You have to put the equalizer in place then swing the shoe spring down.
You can go to settings at the bottom right hand of the video and reduce the playback speed if you need to
Yeah speed thru the process so us amateurs can still be confused thanks for nothing
At the moment I'm sitting at home with a chevy express van and the rear drum brakes are fully disassembled and I couldn't for the life of me figure out how to put it back together until I saw your video. Thanks for putting the pieces together for me....
thank you, and yeah that is the same as a 65 Corvair. new sub and a thumbs UP!!! mike 65 140 Corsa
well done brofessor. you forgot your retainer cups though. all retainer springs have a cup on one side a spring in the middle, and a retainer cup on the top with a pin through it. The last one you assembled had 2 girls but no cup.
looks real easy on the bench, but almost impossible on the car, especially the rear brakes as the big flange limits access. Also, the 'nail' wants to fall back and not let you attach the retainer. So you need to hold the back of the 'nail', then hold the spring and retainer, and counter all the spring forces and then try to attach it. Oh yea, the lower strut arm almost doesn't let you hold the 'nail ' you can barely get one end of a finger on it. Chevrolet engineering at it's best!
GREAT VIDEO! With out it, I would have no rear brakes on my Camaro. Thanks again!
Great video on the GM drum brakes, rebuilding a 1967 Firebird and this is what I needed to know before tearing into the rear brakes, thanks man. Fellow RUclipsr tip: add more keywords to your videos. Let me know if you have questions, be happy to help. Great video!
Dude what's happening
Where’s the wierd washer that goes on the top anchor pin before the springs?
10 years 78 days sober until I saw step 1
Wish he showed how he assembled the spring onto that arm haha
Kinda wished you’d slowed down step by step reassembly must have rewound million times. But never the less. That was the first set of drum brakes ever all new. Thx buddy. I’ve subscribed. And yeah the equalizer plate would’ve went on backwards if you’d not said hump out lol. Yeah it took a few try’s but I got it. Thanks agin. Loved the video.
I hate drum brakes And always knew there had to be an easier way probably because I was doing it out of order or something like that. This video made me not hate drum brakes anymore thank you so very very very much for the help like I said I knew there had to be an easier way and this is it thanks again Happy New Year!!!!!
Excellent. Thanks for speaking to the equalizer bar. I can find no other video that addresses the installation.
Thanks so much I'm 15 and learning how to work on car so this helps a lot
How can I find part number to the pieces I need
The part numbers are in the description.
Minor point, but my GMC shop manual calls the larger rear shoe the secondary shoe and the smaller front shoe the primary shoe.
You're right. There was a lot of beer involved :)
Now do it with an axle flange in the way 😂
I'm so glad I watched this video the truck I just got they had big brake shoe in the front nowonder it wasn't working correctly
Short front light duty shoe is PRIMARY, long heavier material rear shoe is SECONDARY
this video is huge for me. I just tore apart a drum break on a 74 el camino and thought i put it back together right. ill be tearing it apart again and starting over later going step by step with this video lol. Thank you so much for posting this
Guys i Need a Tutorial for an 11 Inch Chevrolet Drum Brake. Is the adjuster always on the side with the longer Blade?
6 minutes in a 2 ads later and still nothing explaining how to rebuilt it. Just fluff. Im out......
Hoping maybe someone can help me out before I go to working on it next weekend. I’ve bled my brakes and adjusted the adjuster but my drum will not fit back on. I spent all day trying to figure it out and can’t
Man, this video helped me out a lot. Someone put the breaks backward on the truck I bought .
Right side was a mess
Does anyone know where to find the spring retaining stud for the front drum brakes, I'm having a very difficult time finding one.
Slow
The hell down and show pieces to camera better
i am working on a CAT forklift and i can't get the wheel cylinder out
i thought it would be only the bolts holding it from back but N!! it's welded too
any idea how to get it out? or it's not supposed to come out ?
the pins were repugnantly rusted and worn out
At the very last step when I put the adjust in place it’s wheel is locking with the spring like the one you put in with your finger. Now my adjuster won’t turn to hear the clicking sound
A little bit dangerious, but I'm sure Bubba has done it plenty of times. 9:40.
The retaining spring is yellow and green. How do you know which one goes left or right. Or does it matter?
It's great having access to this video. I recently bought a 1969 GMC Handi-bus. Its brakes are all drums. I'm an okay mechanic and understand how things work but its been a long time since I worked on old Chevys. Thanks for sharing your expertise. I feel more relaxed about taking on the brakes. Don't worry , I know how to bleed the system. Thanks man... Jon
Great job man, best and most informative video i've seen. I'm working on a 68 camaro. Do you have a list of all the episodes related to my car?
Why didn’t you show no about your emergency brake cable
Thanks man you really helped me out with this video, I’m working on a 76 camaro and I was replacing the rear drum brakes keep on wrenching
No info on the emergency brake cable attachment otherwise it was great info
2:22, you are missing the butterfly washer that separates the shoes from the springs. Btw, backing plates wear out because you fail to apply anti seize to the contact points. You really should apply anti seize to the adjuster and pivot points too. This prevent seizing up, and brake noise. Nice video, but I believe you are missing a self adjuster cable, and a butterfly washer.
It's a light coat of grease not antiseaze.
Excellent video.. Very well defined 👍
is this also the same for the chevy 7.5 rear end??
Thanks. Just needed the time lapse reminder for this old school reassembly. Noticed I’m missing the washer and a broken equalizer spring. Cylinders are cheap but I’ll hone mine and kit it. Bad cup was leaking and hole in dust cover spread it everywhere destroying the shoes, Found an “extra” spring inside but can’t figure out where it came from. Ah, yes, it goes on the adjuster tab. You showed it installed at 9:22 but didn’t comment on it. Been a long time for me but figured it out. Thanks again.
That parking brake cable not shown.
Don’t spread wrong information 😂😂
Well done! Thank you! Happiness!
hello People ....the front shoe the shoe in direction to the front off the car is the Primary.... the Back one is the secondary ....He does everything right he just give the shoe the wrong name.
You make a really interesting point. I just assumed the primary was the shoe that did most of the work. I Googled drum brake diagrams for a few minutes and found them labeled both ways but the majority agreed with you. I just learned something! Thanks Roger.
Hey thank you this helps so much
A lot easier when it’s off the vehicle lol
HUGE help! Thank you sir!
You're welcome!
Great format showing all upfront.
Thank you!
Dude u should be on a tv show like trucks or power nation
Brake tools are cheap.
I never click the LIKE button on these videos (my bad!!!), but I was very impressed with the detail of the video and the detail of the explanations. I just had to share this with you. Thank you so much. I think I can do this now. I hope you have the same video somewhere for the front brakes (foregoing the emergency brake part of the job).
Thank you
God bless you!
Great video that shows the components well and will help many many people. Just a little point, the PRIMARY shoe is the FRONT shoe (the shoe with the shorter liner on it), and the SECONDARY shoe is the rear shoe (the shoe with the longer liner on it). Everything you said is basically correct however the FRONT PRIMARY shoe is held back by a lighter force spring (the blue spring) therefore when the hydraulic cylinder is activated using the brakes the FRONT PRIMARY shoe moves first, which then contacts the drum, as you did explain that causes friction, so the PRIMARY SHOE is forced (rotated) around onto the lower self-adjuster screw, this self-adjuster screw then forces the lower edge of the REAR SECONDARY shoe to move and open outwards, thereafter when the foot pedal force is greater than the force of the green spring holding the top of the REAR SECONDARY shoe, the hydraulic cylinder continues outwards pushing the REAR SECONDARY shoe even further out. Due to the dynamics of the function it is quite normal that the shoes do NOT wear equally, not a problem. Love the vocal energy in your video 🙂
Appreciate the spring setup now I gotta get the brake line off the cylinder probably run new rear line to the T can’t get the line loose from cylinder on my 91 suburban
I was lost, now that I watched your step by step Im found. Your tricks work very well. I guess its all a PROCESS. Thank you.
Thanks for the detailed video! I'm restoring my wife's '64 Impala, starting with the rear brakes. It's been many years since I have worked on drum brakes, so this is a nice refresher course.
Thank you
Thanks
Thank you Sir. Its very much appreciated and Yes i did learn a little bit. i like your way of doing it.
Lots of these older drum brakes are basically the same; thanks for this detailed video; a few finer points to learn here !! Even for an old school guy like me !!!!!!
Thanks building a set of K5 Blazer drums tonight.
I found a problem in my brakes beacause of you !!! My (retired) mechanic iverted the shoes :D Thanks !!!!
Excellent
Damn Thats Pretty! LOL!! Nice Job, the part of this kinda of work I really never liked. The E brake cable replacement! PITA to get em out!!NICE JOB!!
Working on an 84 caprice box chevy and bro this came in clutch. Little late in the day to knock out both sides but hopefully tomorrow I shall have it done. Just need to pick up that tool for the spring and pin cus these pliers ain’t it. Spent most of the day and week looking for a diagram or how tos on how to do them and found nothing. Funny thing is I watched this video last week lmao thanks man definitely helped out.
Forgot the butterfly plate on the top but otherwise nice step by step how to
Thanks! I not sure what part you're talking about. Did I really forget something lol?
@@dickysgarage7120 there's supposed to be an anchor pin plate (butterfly plate) on top, but there's nothing at the start of this video anyway. HAPPY NEW YEAR!!!
Happy New Year! I actually found this application does not use that part. IDK what cars did and didn't but I confirmed a 66 Corvair with 9.5" drums did not use it.
This is the only video I could find that outlines how to install the Raybestos H7008 Hardware Kit including the side specific springs! Thanks!
hi Dick, this example is right or left??, I'm outside of US and replace parts not common find, ahve trouble with star and lever for auto regulation, any tip??
So where's the like for the backing plate 🤷🏾♂️
Gratis video
it was helpful and good system worked out for assembly. I wish the assembly had been in real time. Still a good job. Thanks
Question on my 88 GMC c2500 my drivers side equalizer bar does not have a wide slot on the right side to hook to the EBrake arm and the brake shoe. So does it connect to the EBrake arm only? Thanks
nice and easy thank you
Welcome 😊
Excellent just finished my rear drum brakes on the 69 chevelle great video its been ten years since I did them good refresher!
Excellent quality filming, explanation Premier keep up the awesome work!
Why do you talk like those cheesy Sunday morning car and truck show guys on TV? So corny
Han brak
thanks this is what I needed for my 67 corvair!
Why is there oil in the refrigerator? That is the beer shelf there. More beer if you take the oil out. Thanks
Just did mine, thanks a lot man. Tons of help
Awesome very much helpful, R&R rear drum brakes on my 1967 firebird thanks
video not bad but check out chrisfix he has great videos.
Very helpful. I'd suggest some grease on the inside of the self adjuster threads.
for the passanger side, does the self adjuster lever go on the secondary side
Awesome video, very usfull to me, thanks!!!!
Your video was perfect for my 93 fleetwood brougham..thanks a million
Thank you very much for your helpful video. It was difficult until I saw your video, your video made it easy. Thank you for sharing your knowledge.
Glad it helped!
Great video. Do you or anyone know where to buy those pins that go between the brake cylinder and the shoes?
* Push rod
Deep detail, very honest
Great video. I always removed the springs first. Now I will try it your way.
Glad it helped
Well done, thank you
You drink Royal Purple?
Alex Jones sounding ass.
Nice tutorial, thank you!
Excellent instruction
Well done very helpful