Awesome video!!! Thanks for all the diagnostic help. I found a bad throttle switch on my E-200, no continuity on the brown wires with throttle turned. I will be ordering from you guys tonight. I just want everyone out there watching to know, it takes a lot of time and patience to show step by step how to diagnose a problem correctly and not just throwing parts at it. I work on cars, trucks and small engines and this scooter was kicking my butt!! These are the company's we must buy from!! There not just selling product, there helping us troubleshoot the problem step by step like professionals!! Thanks so much guys! Vito
*Came in today and my friend and I both rode **Latest.Bike** Scooter around for about an hour. Was lots of fun and didn't drain the battery much at all!*
The best video yet; I would like to se a video shown How to test every component in the control box using the multi meter without removing the component.
That would be cool, the thing is the controller is so inexpensive, for most its not going to be worth trying to disassemble and get working. But for guys like me and you, it is fun!
Do you have a video proper installtion and brake adjustment on a e300. I have one feels like I did not install rear tire washer in the proper order. Making lots of clunking sounds.
I need help with installing the battery the wires that were supposed to be on the battery we're not and on the scooter they weren't on they were not they were throwing them out for trash and I've crossed something somewhere and got shocked I need to know how they go please I need to know how to connect the batteries
Excellent Video. Unfortunately, I do not think my problem is addressed here. I've installed new lithium batteries and bought a new charger. The batteries are charged. When my grandson (70 pounds) rides it, it will go about 200 feet then completely stop. Turn the on/off switch off then on again, it will run for another 100 or so feet then stop. I then put in on a bench with no load (wheel off the ground), it ran for over 50 minutes before I stopped it. I called Razor, tech support was useless. Any suggestions would be most appreciated.
Hi, I have a E300. While touching up pain and getting ready to ride I was greasing the back tire and didn’t see the sticker where it says don’t grease… my tire went flat. Can this issue be fixed?
I get a rather large spark when I connect to the scooter with the power switch on. Is that normal? Also, how can you tell if the motor is good? Resistance? I have two scooters and one pushes easier than the other. Is that just because it hasn't been used in a long time (2-3 years)?
I have a razor e325 electric Scooter and it runs for 40 minutes. So I been driving it since 2 years and the battery started to run for only 24 minutes and then I purchased a new battery and it still runs for 24 minutes. I don’t know what the issue is. Can you please help me and reply to see what I can do. Thanks
Replaced the batteries after the click sound. It worked and ran till it died. But when I plugged the charger in it stayed green. I disconnected everything to test everything seemed fine. Hooked it all back up and popped a fuse. Weird.. replaced the fuse and now when I turn the power switch on the scooter just runs. Throttle doesn’t seem to be working. But it has continuity when tested. HELP PLEASE
Cannot test batteries using just voltage readings. Need to test batteries with a load. Can get good voltage reading but batteries may still need to be replaced because they cannot handle loads.
hello pal. my problem is that when i pull the throttle the rely switch trips in then about 1 - 2 second later trips back out. the motor doesn't normally run when doing this.except one time. does it sound like the rely switch in the controller? the battery's holding 25 volts. when i check the yellow and blue when pulling the throttle i dont get over 24 volts coming out to the motor . thanks
i have an E300 that was not working, replaced the batteries and now it works. However it doesn't have much power like it had from new. Could it be the motor which is now the problem. Thanks for any advice
e300 circuit breaker constantly tripping. new batteries. i'm on my second circuit breaker just to take sure its not the case defective new part. i opened up the controller and desoldered STPS3045CT POWER SCHOTTKY RECTIFIER and the F1010E HEXFET® Power MOSFET and tested separately and tested good. it will run for about 50 yards then circuit breaker trips. i'd reset then ride another distance, then trips again. help please. thank you.
I am trying to bypass my reset switch and replace it with a spare fuse I have. Do you happen to know the awg for the wire for the stock fuse cables for razor? I can only find that it says 450/750v on there. Thanks for the videos you guys put out I was able to fix my sons scooter because of you guys.
I bought lithium iron phosphate two 12 V 7 AH battery and when I stand on the scooter it works for a second and then stops working. What might be the issue you think and can you help me with that?
I just replaced rear tire and inner tube and batteries on my sons e300. Charged new batteries for 12 hrs. I get on it to test it and it’s gutless and slow and motor doesn’t always kick in.
@@williamhickey982 The normal issue here is you got cheap batteries. Cheap = Junk. You get what you pay for. We have quality, and genuine razor batteries in stock. Dont buy the cheap batteries guys, they have low output!
So when I charge my e300, it shows it’s fully charged after I charge it for a solid 12 hours, but it pulls really slowly and after a couple hundred feet it just stops going. I turn it off then back on and it does the same thing again. I replaced the batteries and everything and don’t know what else I can do, help!
Same here. Took batts out of a working identical scooter that works fine. So batts are good, tires inflated, brake not stuck chain fine, wheel spins freely. Wheel spins with throttle when off the ground. Any weight on it and it doesn't want to move. If on scooter and push to get it going will still barely move. I keep seeing this asked but when people say it's not the batteries everyone goes silent.
My scooter Both batteries put out 12 v when I test them with the multimeter but when I give it throttle it spins but doesn't even have the power to move its self and the scooter shows battery fully charged
can you help me, i have just put new batteries in e300 and the motor runs as soon as i turn the scooter on ive checked the throtle its ok , so im thinking its the control box but what can i do to fix it please please help me
Very nice video. I did all the testing you mentioned here but unfortunately my e200 still not working. I have no voltage coming out from the controller box to the motor. I believe is my controller box(no clicking either). Thanks for the video.
working on e300. back tire spins but can easily stop it by hand. scooter wont pull weight... have new batteries... which are fully charged... any suggestions???
@@WildPowerSports The batteries have a low threshhold and if charge falls below threshold will not charge back to full charge. Result need new batteries. Leaving switch on for many days can cause this problem
@@lesbiapatriciaandrade8951I have an E300s.. where can I find the threshold? I put in new batteries, the light on the charger was green right away, but the scooter only made a clicking sound. I charged for several hours and now I can hear the motor starting then fading out, but the wheel doesn't turn.
Our E200 always shows a green light on the charger but will not run. The red light on the charger is never on. The scooter is showing charged all the time but is obviously not. Any suggestions as to the problem???
Mine doesn't click when I turn the throttle. The red power light comes on, the breaker pushes in and comes right back out. I'm thinking it's the main brain or less likely the throttle wire. Any suggestions would be really appreciated. Thank you all.
Anytime I connect a battery to the motor it sparks and nothing happens. Is there a short in the wires? I also get a beep when touching the wires to the motor. That should not happen
Got it working ok. I'm trying to make my Schwinn go farther , I have a 500 w motor(chain run) 24 v (2) but I only get around ehhhh a mile or so on it , whish I could get at least 10 miles on full charge :(
My girlfriends son has a Razor E300. When charging it, it will not charge. Tested the charger and thats fine. Would a controller be the reason it isn't charging up?
I have an E300 that has 24v showing off my batteries, but when I give it throttle, it has no power. Wheel spins, but if you stand on it, it doesn't have enough power to move you! Please help!
It works when put to the side and then when I try to ride it, it goes very slow please help. I think the motor can’t handle its own weight. Maybe I need to replace the motor. Do you know the problem? Please help me. The battery charger light stays green
Same thing happening to me I recently got a e300 from a friend n I charged it n it green light but when I ride it it ride very slow like it wanna stop so i think it the motor
How do you do the secret trick to test the throttle on a Version 1 Razor Sport Mod? It has 5 wires. I tried the clip the way you did in the connector and got nothing, but maybe 5 wire variable throttles won't react the same as the 4 wire that you did in video? I can jump from battery to motor direct and the motor runs fine. I tested EVERYTHING you did in the video, and I replaced the controller AND the throttle and I still got nothing! I'm going to scrap it/give it away but in case anyone reads this post I may be able to save it. I've been through the schematics, I've tried so many things I am out of ideas except for the current thought: You can't do the special throttle trick on the 5 wire sport mod (variable throttle) AND I bought a faulty throttle OR faulty controller and don't know which...... But one thing for sure---backprobing the connector for the throttle, I have voltage to the throttle and different voltages in the connector, NONE will change value when twisting the throttle. They stay the same! So I figure it's the throttle.
The issue in all these cases is almost 100% batteries. Even new, there could be an issue. If one is low and the other is fully charged the low one will hold back the scooter and never fully charge. Other than that the only issue it could be is tire pressure! Yes, its that important on these! I weigh 173 and with me on an E300 with a low tire it will barely move!
@@TheSkyPod It comes with the scooter, inside the right handlebar! We also have them in stock, look for "universal valve extender" on wildscooterparts.com
My Razor E300 turns on, batteries 25.2 volts throttle responds when off ground, the moment i jump on, it's got no oomph and I'm only 64kgs. please help
Hey was hopping mabby you could help.have a e200 was working great save battery was dying .bought two new ones replaced and it will only click .light turns on worked 100% freaking out . Says it's charging
hi all, i'm restoring an old Mitsuca scooter. Motor runs perfect when i put 24 volt on it however when i let it pass trough the controller it runs very very slow on full throttle. Did the throttle test as in the electricscooterparts.com throttle testing guide and reading came out at 3.57-3.58 volt so should be OK. Brake port is open so should be OK too.... Battery is also OK (brand new and charged fully) What else can it be? Anyone has a clue?
This is VERY common, happens on almost every unit. This is due to extreme use, the wires heat up and melt the connector. The solution is to cut the connector off and solder the wires direct.
I have a Razor Betty 24v., new batteries and a (2nd) new control module. The first kept kept blowing fuses as soon as I turned it on. After taking module apart, the insides were fried. After installing the newest one, I'm having the same problem. I walked away from it rather than burn up the newest one. Is there anyone who can help me. Thank you so much!
I have this battery tester: smile.amazon.com/gp/product/B000BOBZJ0/ Can I still test the circuit breaker with it? (mine doesn't beep that I'm aware of. It is analog so the needle goes to red or green if battery is good/bad) I ruled out bad batteries or at least the tester indicates the batteries are good. Our E300 scooter clicks but that is it. wanting to test the circuit breaker. Pushing the reset button in, it doesn't stay in. Is it supposed to? What do I need to buy to test the circuit breaker? I don't see a continuity option on my battery tester.
@@WildPowerSports he means to have each section of the video where you troubleshoot each part, separated by time stamps by putting the beginning time for each segment in the description. So for example: battery troubleshooting: 1:00 Throttle troubleshooting: 5:00 Motor troubleshooting: 8:00 Something like that
This is my first scooter and probably the best toy I've had in my 38 years of life ; ) ruclips.net/user/postUgkxvyNuxpWiHTNypxG6nyqyf7ywc7Q16PDM The assembly was easy - Took me 10-12 mins to get it set up and enjoy a quick ride before putting it on the charger for the full charge.I love the push-off feature vs. some of the other scooters that start with direct acceleration. I believe this allows a bit more of a stable start with a jerk reaction. I also like the throttle/acceleration feature that its a slow increase in speed vs. what you would get in a motorcycle. I've taken advantage of the anti-theft system when taking the scooter out to the beach and city. I like the anti-theft system as well as the need to enter a code after you turn it on before you can operate. The powerful front lights are helpful for a night ride. You can see in the picture how powerful the light is as a reflection on the garage. I'm impressed with the lightweight and how easy it was for me to get it set up and going. I would highly recommend this for someone looking for a scooter.
Hey bud, the company for street razor here in Tempe Az when out of business, they sold everything and I bought 2 Brand new in the box and I was just wondering if you can help me out to make them run . That's the ones you use a credit card I'm sure you are seeing all over the streets . NOT STOLEN,, Brand new razor . I can send you my email if that helps , thanks.. ( E 300 ) they said. I don't know.
Question: on my scooter when I charge the battery there is a strong sulfur smell. The batteries were swollen so I replaced them. When I charged the new batteries I got the same sulfur smell. Could it be the AC charger?
Awesome video!!! Thanks for all the diagnostic help. I found a bad throttle switch on my E-200, no continuity on the brown wires with throttle turned. I will be ordering from you guys tonight. I just want everyone out there watching to know, it takes a lot of time and patience to show step by step how to diagnose a problem correctly and not just throwing parts at it. I work on cars, trucks and small engines and this scooter was kicking my butt!! These are the company's we must buy from!! There not just selling product, there helping us troubleshoot the problem step by step like professionals!! Thanks so much guys! Vito
Thank you! We try to guide everyone to the answer instead of just ordering every part!
*Came in today and my friend and I both rode **Latest.Bike** Scooter around for about an hour. Was lots of fun and didn't drain the battery much at all!*
I use the battery in my 19.6v drill and it works very well for testing the motor
Nice idea !! Thanks
Nice I'm going to try this on an e300 just purchased as a none runner... thanks ...
The best video yet; I would like to se a video shown How to test every component in the control box using the multi meter without removing the component.
That would be cool, the thing is the controller is so inexpensive, for most its not going to be worth trying to disassemble and get working. But for guys like me and you, it is fun!
I have a blue one up to 9 miles an hour and I live in Minnesota so I always take it out in the snow and it works wonderfully
Bad brake switch! Finally found it, thanks!
We’re is the brake switch. I have my I unplug the two Brake wires and it works can I leave them off
Thanks this helped me fix my son's scooter, turns out it was the throttle and I can get it on Amazon for less than $20! Thanks man!
So you use our video to learn how to repair it, then go to amazon to buy a part. Maybe buy from us next time????
Thanks! This really is EVERYTHING Broken down into clear instructions brilliant!!!!
I just bought me a new razor e300/s scooter chain from wild scooter parts ebay. Thanks again for the video.
Fixing these babies is nothing more than a labour of love.The cost for the batteries alone far exceeds how much they fetch.
Pat Butete there only 35
Try getting batteries on line or at Batteries Plus
@@lesbiapatriciaandrade8951 Batteries plus??? They charge a FORTUNE. Get them from us, the ones who made this video, wildscooterparts.com
Great explanation thank you
Awesome I fixed my sons scooter! Thank you!
Great video -really helpfull
Excelente video! Very clear explanation. Thanks
Do you have a video proper installtion and brake adjustment on a e300. I have one feels like I did not install rear tire washer in the proper order. Making lots of clunking sounds.
Controller stopped reversed polarity any part I can replace ? fuse on board ?
I need help with installing the battery the wires that were supposed to be on the battery we're not and on the scooter they weren't on they were not they were throwing them out for trash and I've crossed something somewhere and got shocked I need to know how they go please I need to know how to connect the batteries
I got a new motor and set of new batteries but no throttle response not even the click. Power switch works. So think it’s the breaker or throttle?
Excellent Video. Unfortunately, I do not think my problem is addressed here. I've installed new lithium batteries and bought a new charger. The batteries are charged. When my grandson (70 pounds) rides it, it will go about 200 feet then completely stop. Turn the on/off switch off then on again, it will run for another 100 or so feet then stop. I then put in on a bench with no load (wheel off the ground), it ran for over 50 minutes before I stopped it. I called Razor, tech support was useless. Any suggestions would be most appreciated.
do you resolve the problem?? i have the same
When you go lithium or to a voltage not supported byt he factory parts we cant help unless we have the machine here. So many things it could be.
Hi, I have a E300. While touching up pain and getting ready to ride I was greasing the back tire and didn’t see the sticker where it says don’t grease… my tire went flat. Can this issue be fixed?
I get a rather large spark when I connect to the scooter with the power switch on. Is that normal?
Also, how can you tell if the motor is good? Resistance?
I have two scooters and one pushes easier than the other. Is that just because it hasn't been used in a long time (2-3 years)?
Spark is normal. Connect the motor directly to a 12v battery!
I have a razor e325 electric Scooter and it runs for 40 minutes.
So I been driving it since 2 years and the battery started to run for only 24 minutes and then I purchased a new battery and it still runs for 24 minutes.
I don’t know what the issue is.
Can you please help me and reply to see what I can do.
Thanks
Replaced the batteries after the click sound. It worked and ran till it died. But when I plugged the charger in it stayed green. I disconnected everything to test everything seemed fine. Hooked it all back up and popped a fuse. Weird.. replaced the fuse and now when I turn the power switch on the scooter just runs. Throttle doesn’t seem to be working. But it has continuity when tested. HELP PLEASE
I’m getting the same problem
Kinda
Wow, this is a weird one. Controller/throttle issue. Would have to see it here to diagnose.
How many volts should I be showing coming out of the charging port of the controller?
We never check here, as its not really necessary to do, so not sure on this.
I've recently acquired a second hand e300, doesn't require a kick boost to go, but has no torque when riding.
HI, did youu solve it?? i have the same issue
Cannot test batteries using just voltage readings. Need to test batteries with a load. Can get good voltage reading but batteries may still need to be replaced because they cannot handle loads.
hello pal. my problem is that when i pull the throttle the rely switch trips in then about 1 - 2 second later trips back out. the motor doesn't normally run when doing this.except one time. does it sound like the rely switch in the controller? the battery's holding 25 volts. when i check the yellow and blue when pulling the throttle i dont get over 24 volts coming out to the motor . thanks
i have an E300 that was not working, replaced the batteries and now it works. However it doesn't have much power like it had from new. Could it be the motor which is now the problem. Thanks for any advice
Hi my E300 scooter needs new batteries. Is replacing them something anyone can do or is it something only a scooter tech can do?
e300 circuit breaker constantly tripping. new batteries. i'm on my second circuit breaker just to take sure its not the case defective new part. i opened up the controller and desoldered STPS3045CT POWER SCHOTTKY RECTIFIER and the F1010E HEXFET® Power MOSFET and tested separately and tested good. it will run for about 50 yards then circuit breaker trips. i'd reset then ride another distance, then trips again. help please. thank you.
the drive tire spins freely so its not the case of brakes sticking.
Sounds like a short. Make sure no exposed wires are touching metal. Controller not the issue.
I am trying to bypass my reset switch and replace it with a spare fuse I have. Do you happen to know the awg for the wire for the stock fuse cables for razor? I can only find that it says 450/750v on there. Thanks for the videos you guys put out I was able to fix my sons scooter because of you guys.
12 Gauge....
I bought lithium iron phosphate two 12 V 7 AH battery and when I stand on the scooter it works for a second and then stops working. What might be the issue you think and can you help me with that?
Very nice video
I put new batteries in but they die out quick ? What could be the problem 😕
I just replaced rear tire and inner tube and batteries on my sons e300. Charged new batteries for 12 hrs. I get on it to test it and it’s gutless and slow and motor doesn’t always kick in.
I’m having the same problem. Did you find a solution?
@@williamhickey982 The normal issue here is you got cheap batteries. Cheap = Junk. You get what you pay for. We have quality, and genuine razor batteries in stock. Dont buy the cheap batteries guys, they have low output!
So when I charge my e300, it shows it’s fully charged after I charge it for a solid 12 hours, but it pulls really slowly and after a couple hundred feet it just stops going. I turn it off then back on and it does the same thing again. I replaced the batteries and everything and don’t know what else I can do, help!
I have that problem as well still don’t know how to fix it
That's exactly what mine is doing too. ?
Are your tires inflated properly?
They were low, so I inflated them well and it still bogs down and won't go.
Same here. Took batts out of a working identical scooter that works fine. So batts are good, tires inflated, brake not stuck chain fine, wheel spins freely. Wheel spins with throttle when off the ground. Any weight on it and it doesn't want to move. If on scooter and push to get it going will still barely move. I keep seeing this asked but when people say it's not the batteries everyone goes silent.
I need help with my throttle colors plugh
My scooter Both batteries put out 12 v when I test them with the multimeter
but when I give it throttle it spins but doesn't even have the power to move its self and the scooter shows battery fully charged
same issue!
Did you ever figure this out? Mine is having the same problem after getting new batteries
can you help me, i have just put new batteries in e300 and the motor runs as soon as i turn the scooter on ive checked the throtle its ok , so im thinking its the control box but what can i do to fix it please please help me
Very nice video. I did all the testing you mentioned here but unfortunately my e200 still not working. I have no voltage coming out from the controller box to the motor. I believe is my controller box(no clicking either). Thanks for the video.
Got almost same things, checked everything all good, clicking good still doesn’t work this little 🤔 drive me crazy
working on e300. back tire spins but can easily stop it by hand. scooter wont pull weight... have new batteries... which are fully charged... any suggestions???
did you solve it?? i have same issue
Hey my e300 works but slow of there's any weight on it. When the back tire is off the ground it goes great and fast. Any idea what it could be?
Batteries. Most likley bad. Check voltage under load.
hi, did you solve it?
working on e300. back tire spins but can easily stop it by hand. scooter wont pull weight.
Bad batteries.
Make sure air pressure in tire is correct.
ive just put new battery's in mine but it only holds its charge for maybe 2/3 minuets could it be the controller...ive changed chargers also
99% chance bad batteries.
my motor works and i tested everything else but no torque when i ride it. has to be the controller then?
Bad Batteries.
My son's e300 only lasts about 10min even with brand new batteries ?
Bad charger or bad battery (Yes, they can be bad new) most likely. Other issues could do it, but thats the most common.
Yes mine is like that, 40 min no way 100 kg no way probaly same battery as kids one
@@WildPowerSports The batteries have a low threshhold and if charge falls below threshold will not charge back to full charge. Result need new batteries. Leaving switch on for many days can cause this problem
@@lesbiapatriciaandrade8951I have an E300s.. where can I find the threshold? I put in new batteries, the light on the charger was green right away, but the scooter only made a clicking sound. I charged for several hours and now I can hear the motor starting then fading out, but the wheel doesn't turn.
Our E200 always shows a green light on the charger but will not run. The red light on the charger is never on. The scooter is showing charged all the time but is obviously not. Any suggestions as to the problem???
I bought a new charger on Amazon for $10 and fixed this issue. I know I'm 2 years late to the party!
Mine doesn't click when I turn the throttle. The red power light comes on, the breaker pushes in and comes right back out. I'm thinking it's the main brain or less likely the throttle wire. Any suggestions would be really appreciated. Thank you all.
Gracias por toda la información
Anytime I connect a battery to the motor it sparks and nothing happens. Is there a short in the wires? I also get a beep when touching the wires to the motor. That should not happen
So, if the light is green when plugged to the scooter should it go on to red to say is charging and green for fully charged?
Correct, if not, hit us up for batteries. Again, the cheap batteries only last a few months, so get quality ones from us!
Got it working ok. I'm trying to make my Schwinn go farther , I have a 500 w motor(chain run) 24 v (2) but I only get around ehhhh a mile or so on it , whish I could get at least 10 miles on full charge :(
My girlfriends son has a Razor E300. When charging it, it will not charge. Tested the charger and thats fine. Would a controller be the reason it isn't charging up?
Could be, but could be batteries also.
I have an E300 that has 24v showing off my batteries, but when I give it throttle, it has no power. Wheel spins, but if you stand on it, it doesn't have enough power to move you! Please help!
me also
It works when put to the side and then when I try to ride it, it goes very slow please help. I think the motor can’t handle its own weight. Maybe I need to replace the motor. Do you know the problem? Please help me. The battery charger light stays green
Same thing happening to me I recently got a e300 from a friend n I charged it n it green light but when I ride it it ride very slow like it wanna stop so i think it the motor
I found out it was the controller not the motor
Sometimes I pull the throttle and it goes, and sometimes it doesn’t. Any thoughts?
Possible bad throttle....
@@WildPowerSports thank you, it works just on the 2nd or 3rd pull
🎉 it's the real thing 🎉
How do you do the secret trick to test the throttle on a Version 1 Razor Sport Mod? It has 5 wires. I tried the clip the way you did in the connector and got nothing, but maybe 5 wire variable throttles won't react the same as the 4 wire that you did in video? I can jump from battery to motor direct and the motor runs fine. I tested EVERYTHING you did in the video, and I replaced the controller AND the throttle and I still got nothing! I'm going to scrap it/give it away but in case anyone reads this post I may be able to save it. I've been through the schematics, I've tried so many things I am out of ideas except for the current thought: You can't do the special throttle trick on the 5 wire sport mod (variable throttle) AND I bought a faulty throttle OR faulty controller and don't know which...... But one thing for sure---backprobing the connector for the throttle, I have voltage to the throttle and different voltages in the connector, NONE will change value when twisting the throttle. They stay the same! So I figure it's the throttle.
I put new batteries in and used a new charger. The motor runs fast when off the ground, but when I step on the scooter it is very slow.
Mine is like that even when wont move with me on it, step off and it moves no problem
@@ramblingrob4693 motor might not be getting enough voltage. see if you can test the voltage going to the motor.
The issue in all these cases is almost 100% batteries. Even new, there could be an issue. If one is low and the other is fully charged the low one will hold back the scooter and never fully charge. Other than that the only issue it could be is tire pressure! Yes, its that important on these! I weigh 173 and with me on an E300 with a low tire it will barely move!
@@WildPowerSports What kind of fitting is needed to put air in that back tire ? Fricken thing is set inside the sprocket .
@@TheSkyPod It comes with the scooter, inside the right handlebar! We also have them in stock, look for "universal valve extender" on wildscooterparts.com
My e200 is fully charged the battery is good and working but the throttle just won’t work
My Razor E300 turns on, batteries 25.2 volts throttle responds when off ground, the moment i jump on, it's got no oomph and I'm only 64kgs. please help
Hey was hopping mabby you could help.have a e200 was working great save battery was dying .bought two new ones replaced and it will only click .light turns on worked 100% freaking out . Says it's charging
Did the test to see if it's throttle and it won't go also won't go if brakes are out just clicks .any idea thanks a million
Hey, so I replaced the batteries, I turn the throttle and hear a click. But the motor doesn't go.
Please see our videos, follow the steps.
awesome, thanks
hi all, i'm restoring an old Mitsuca scooter. Motor runs perfect when i put 24 volt on it however when i let it pass trough the controller it runs very very slow on full throttle. Did the throttle test as in the electricscooterparts.com throttle testing guide and reading came out at 3.57-3.58 volt so should be OK. Brake port is open so should be OK too.... Battery is also OK (brand new and charged fully) What else can it be? Anyone has a clue?
What is the reset switch for
Overload or Short conditions
Can anyone tell me what would cause the connectors to melt.(battery cables)
This is VERY common, happens on almost every unit. This is due to extreme use, the wires heat up and melt the connector. The solution is to cut the connector off and solder the wires direct.
I have a Razor Betty 24v., new batteries and a (2nd) new control module. The first kept kept blowing fuses as soon as I turned it on. After taking module apart, the insides were fried. After installing the newest one, I'm having the same problem. I walked away from it rather than burn up the newest one.
Is there anyone who can help me.
Thank you so much!
Sounds like there is somthing causing extreme load on the motor. Does thw wheel spin freely? Are you overloading the scooter?
What if your scooter tire runs but when u stand on it it doesn't go
Bad batteries, low tire pressure. 99.999% sure on that. Watch the phantom voltage video.
Hello I change two new batries and I have the same problem every day my problem is the very low range can some one help??
What brand and where did you get the batteries from?
Hi ai have and me one but no work and i dont know tow mack i need your help plz You its for mai san
Can u send me a pic of the top of the battery
Don't have any here right now, but simply look up the wiring diagrams in the support section on wildscooterparts.com
Yep, my battery voltage was 13. Eeeek
Mine is still not working
I have this battery tester: smile.amazon.com/gp/product/B000BOBZJ0/
Can I still test the circuit breaker with it? (mine doesn't beep that I'm aware of. It is analog so the needle goes to red or green if battery is good/bad) I ruled out bad batteries or at least the tester indicates the batteries are good. Our E300 scooter clicks but that is it. wanting to test the circuit breaker. Pushing the reset button in, it doesn't stay in. Is it supposed to? What do I need to buy to test the circuit breaker? I don't see a continuity option on my battery tester.
Hey can u fix and boost my scooter I live in NY
We would love to, but you would need to ship it to us in Denver, CO.
time stamps would be nice.
Time stamps? Anything to help, but can you be more precise on how time stamps would help?
@@WildPowerSports he means to have each section of the video where you troubleshoot each part, separated by time stamps by putting the beginning time for each segment in the description. So for example:
battery troubleshooting: 1:00
Throttle troubleshooting: 5:00
Motor troubleshooting: 8:00
Something like that
Nice scooter. But the weight is double than a scooter twice the range and speed
thanks for the help daddy
😍😘😗😚
THANK CHRIST FOR THIS MADE IN CHINA MYSTERIO !!! very useful vid!!!
Lmao that’s what I was thinking
When I turn my electric scooter on the motor automatically spins making the back wheel turn so it keep going forward without me touching the frottle
The website for scooter part wildscooterparts.com ?
correct!
You need to give it a little push
Great video, but for anyone reading this, I recommend just simply not buying a Razor scooter. They're more trouble than they're worth
Thanks. Really they are like anything else, just maintain them and know whats going on and you will have a good experience!
@@WildPowerSports as a razor technician can say that Razor electric scooters are the best made scooters. Replacement parts available
This is my first scooter and probably the best toy I've had in my 38 years of life ; ) ruclips.net/user/postUgkxvyNuxpWiHTNypxG6nyqyf7ywc7Q16PDM The assembly was easy - Took me 10-12 mins to get it set up and enjoy a quick ride before putting it on the charger for the full charge.I love the push-off feature vs. some of the other scooters that start with direct acceleration. I believe this allows a bit more of a stable start with a jerk reaction. I also like the throttle/acceleration feature that its a slow increase in speed vs. what you would get in a motorcycle. I've taken advantage of the anti-theft system when taking the scooter out to the beach and city. I like the anti-theft system as well as the need to enter a code after you turn it on before you can operate. The powerful front lights are helpful for a night ride. You can see in the picture how powerful the light is as a reflection on the garage. I'm impressed with the lightweight and how easy it was for me to get it set up and going. I would highly recommend this for someone looking for a scooter.
Hey bud, the company for street razor here in Tempe Az when out of business, they sold everything and I bought 2 Brand new in the box and I was just wondering if you can help me out to make them run . That's the ones you use a credit card I'm sure you are seeing all over the streets . NOT STOLEN,, Brand new razor . I can send you my email if that helps , thanks.. ( E 300 ) they said. I don't know.
Question: on my scooter when I charge the battery there is a strong sulfur smell. The batteries were swollen so I replaced them. When I charged the new batteries I got the same sulfur smell. Could it be the AC charger?