Not all heroes wear capes - buying few of those next month. Put the link to buy them into video’s description as that is the first place I looked - most people will miss it otherwise.
Like someone asked before : can this be used to calibrate xbox elite (v1) controller? Can you share the link to the replacement parts? And link to software please?
Do you have a written out instruction or pdf walkthrough how to activate each mode after installation? I have watched video walkthrough numerous time and have been unable to enter any calibration mode.
yah, did all that, even went to older videos to verify install was 100% with the battery plug-in and led flash on pcb boards all good and still no go. I'm hoping if Zeng is serious about getting this to as many customers as possible a legitimate installation guide/pdf with clear and clarified steps is needed asap. @@user-ni4bc2bm7c
Can PS4 hall effect joysticks work for PS5 as long as it has your driver board? In theory it should since your driver board corrects the signal coming in and puts out the proper one?
Ok this is my first time learning about this modification and i have some questions. 1.- only works with an exclusive stick nodel? 2.- i saw your modification in a xbox elite series 2 controller and i wanna know if can i do the same calibration 3.- it works on switch pro controller? 4.- the driver that everyone made mention in the comments run in the pcb or i need to use a software in PC?
you cant do it on xbox elite controller because the removeable joysticks are magnetic and it will intefere with the hall effect. HOWEVER if you swap the removable joystick for normal plastic ones it should work.
My left one is no longer calibrating, only the right one, what could it be? I already calibrated it previously, but now I only calibrate the right one.
Believe it or not the normal fix for this is the calibration isn’t set. Hold down the joystick and plug in controller and do complete 360 rotations with the joystick and when done press down again and then test.
@@TheNightWalkerTM so no matter the Hall effects as long as they have the proper sensors for that console so you’re good. I if the board is installed properly on your controller you just need to enter all three modes and set it ups you should have 3-6 % accuracy issue when testing. For examples with yours being 25% you likely didn’t enter the mode that captures the full 360 rotation
@@TheNightWalkerTM I see what you’re talking about. Wanting to see if his board would work for your Hall effects. Yes is the answer. It modify input and allow you to adjust output
I have the v5 board and am having trouble getting into the calibration modes. My left joystick can get into calibration mode A (center point) but my right joystick can't. It seems like both joysticks can get into calibration mode S but I'm not sure my changes are working (I'm pressing L3 and R3 after moving the joysticks in circles). I can only get my left joystick into calibration mode B. When I'm not in calibration mode, both joysticks are able to reach all directions. I can't seem to get my right joystick into calibration modes A or B. Any advice?
I'm just browsing but my own intuition would lead to thinking that your driver board for the right stick just isn't installed properly if it's not entering calibration modes at all, since that's the point of the board. Not sure however.
@@junZeng-520Hi, can I calibrate triggers with this tool, because I just bought Xbox Series Controller and right trigger has a 2 mm. dead zone at the end.
Im having trouble getting it to enter the editing modes. It seems to always just load back in to the circularity test. Any help would be GREATLY appreciated.
@@junZeng-520 I'm using a dual analog adaptive controller using 2 Sanwa JLMs. Will this method work for them? I can't seem to get any info on them as they aren't sold here in the US. Any advice you have would be GREATLY appreciated
@Plaojuo yeah thanks for the generous comment d bag. The joysticks are both hall effect sensor joysticks, which is why I asked. A simple no would have been fine.
Hello brother, you don't have to be confused, simply by pulling the joystick, and then turn on, he will enter different modes, you can adjust the center point of the joystick and external range.
You need to turn on the controller for a moment, your fingers do not touch the joystick. The program decides what it should do the moment it starts up.
@@kevindesmond2120 My drive board doesn't support the edge controller, but some players have tried it and it's said to be fine. Better to wait until I come out with an EDGE-compatible version.
I'd love to do a review on your product, can you give me a link to your store? The calibration was amazing! Also which hall effect sensors would give me the best result? I have the orange ones which I did a review on. But I'm interested in the blue K-silver ones which I haven't tested.
@@jedxyrusenterina4764 Hello, my friend. My black to drive circuit board inside with my program, the video inside the test joystick data is a test page. gamepad-tester.com
@@NicolasSilvaVasault pensaba que había que usar un programa pero resulta que al montar los joystick magneticos hay que montar también los driver de calibración que van también soldados, la página para calibrar los joystick ya la conocía pero para poder entrar en esos modos de calibración tienes que tener montado esos driver pcb, también voy a pedir en aliexpres el cabezal para soldadores t12 que te permite desmontar los joystick muy fácilmente y en un minuto, te ahorra mucho trabajo.
yo compre los naranjo hace poco, y si bien funcionan mucho mejor que los que usan potenciometro, calibrarlos es una patada en las bolas, porque tienes que hacer un juego entre el analogo y un punto al que insertar una aguja, y cuesta un monton porque a veces se te va, en cambio estos con el pcb la calibracion es milimetrica y no tienes que desarmar nada, pero la diferencia de precio es grande, $20 USD vale el par de estos @@MiguelAngel-ij1oh
![Seungmin "그렇게, 천천히, 우리(As we are)" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/kAzmhLHePqU/mqdefault.jpg)
Not all heroes wear capes - buying few of those next month. Put the link to buy them into video’s description as that is the first place I looked - most people will miss it otherwise.
please tell me how can I enter the settings in the pad to calibrate it like that because it doesn't work for me,
Like someone asked before : can this be used to calibrate xbox elite (v1) controller?
Can you share the link to the replacement parts? And link to software please?
After this is done will the controller work well on PS5 or is it only for pc?
Do you have a written out instruction or pdf walkthrough how to activate each mode after installation? I have watched video walkthrough numerous time and have been unable to enter any calibration mode.
Watch what he does when plugging in the controller you put different analogue inputs to enter the various modes and save them by clicking R3 or L3
yah, did all that, even went to older videos to verify install was 100% with the battery plug-in and led flash on pcb boards all good and still no go. I'm hoping if Zeng is serious about getting this to as many customers as possible a legitimate installation guide/pdf with clear and clarified steps is needed asap. @@user-ni4bc2bm7c
How do you reset to factory settings? I think I messed up the calibration and I can't get it right anymore. Thanks.
Lmk if you figure it out
There is no need to reset, just do it until you get it right
does this pcb board works with the hall effect module from other manufacturer (the yellow-yellow one) and any option to buy them separately?
Can be used with yellow color module. I have the AliExpress link
links to the driver board,or its name??
Hi I have hall effect sticks in my controller can I calibrate them like this?
if you have the pcb installed in the controller yes, if you got the orange hall effect ones then no
Can PS4 hall effect joysticks work for PS5 as long as it has your driver board? In theory it should since your driver board corrects the signal coming in and puts out the proper one?
is there hall effect joystick for xbx elite series 2 controller with no jitter or noise?
Hello! I am interested in purchasing this module, does the calibration cause a dead zone or input lag?
Перепаять было сложнее всего, но все получилось. Спасибо большое за видео и помощь! Дети будут счастливы)
Ok this is my first time learning about this modification and i have some questions.
1.- only works with an exclusive stick nodel?
2.- i saw your modification in a xbox elite series 2 controller and i wanna know if can i do the same calibration
3.- it works on switch pro controller?
4.- the driver that everyone made mention in the comments run in the pcb or i need to use a software in PC?
you cant do it on xbox elite controller because the removeable joysticks are magnetic and it will intefere with the hall effect. HOWEVER if you swap the removable joystick for normal plastic ones it should work.
My left one is no longer calibrating, only the right one, what could it be? I already calibrated it previously, but now I only calibrate the right one.
Would this work with the Orange and Red board Hall effect joysticks for PS5? I just installed them and 25% circularity is rough
Believe it or not the normal fix for this is the calibration isn’t set. Hold down the joystick and plug in controller and do complete 360 rotations with the joystick and when done press down again and then test.
@@TheModgenius are you talking about the board he installed or just the hall effect joysticks
@@TheNightWalkerTM so no matter the Hall effects as long as they have the proper sensors for that console so you’re good. I if the board is installed properly on your controller you just need to enter all three modes and set it ups you should have 3-6 % accuracy issue when testing. For examples with yours being 25% you likely didn’t enter the mode that captures the full 360 rotation
@@TheNightWalkerTM I see what you’re talking about. Wanting to see if his board would work for your Hall effects. Yes is the answer. It modify input and allow you to adjust output
It works with dualsense edge?
Does this only work with battery powered controllers or would it work with razer wolverine that is corded but the cord is removable?
I have the v5 board and am having trouble getting into the calibration modes. My left joystick can get into calibration mode A (center point) but my right joystick can't. It seems like both joysticks can get into calibration mode S but I'm not sure my changes are working (I'm pressing L3 and R3 after moving the joysticks in circles). I can only get my left joystick into calibration mode B. When I'm not in calibration mode, both joysticks are able to reach all directions. I can't seem to get my right joystick into calibration modes A or B. Any advice?
I'm just browsing but my own intuition would lead to thinking that your driver board for the right stick just isn't installed properly if it's not entering calibration modes at all, since that's the point of the board. Not sure however.
Have we came up with a solution to the jitter problem? I know the boards don’t correct this.
To make this easier I purched a usbc-c cable with an inline switch. No more plugging and unplugging the usbc-c
This is really necessary if you use it a lot
But like you have to do this everytime you turn of the controller or what? After you calibrate is it not saved?
@@stefansaran7904it's saved after you calibrate
Is there a way to reset the calibration and start over?
There doesn't seem to be a reset but you can basically just keep retrying and adjusting until they're how you like them.
Whee we can buy ?? Ali links are broken...
How can i access this tool?
With the hall sensor joysticks installed and calibrated what is the input lag after the ps5 controller is overclocked?
No lag was felt. It is recommended that you find out by testing, because everyone feels differently.
@@junZeng-520you should measure the input lag of normal analog and your kit for comparison.
Can you provide links for those modules, would like to replace them on both my controllers... Thanks
Does this only work with hall effect? Or also with a regular one?
You need hall effect plus his PCB board
how do you do it? through some program or website? please provide solution. because my pad has too little range
He used a calibration board, it's put inside the gamepad, you have to buy it separately
How to get your calibration manual?
I'm selling on AliExpress
www.aliexpress.us/item/3256805732082103.html?gatewayAdapt=glo2usa4itemAdapt
@@MidnightCoding yes
@@junZeng-520 Link is down?
Hi! I'm interested in buying a kit for my ps4 controller. The calibration process is the same?
YES
@@junZeng-520Hi, can I calibrate triggers with this tool, because I just bought Xbox Series Controller and right trigger has a 2 mm. dead zone at the end.
@@vovazagach1781 The right trigger? I'm sorry this can't be used to calibrate the trigger
@@junZeng-520 Thanks, but maybe you can tell why right trigger has a dead zone, cause it shouldn't.
@@vovazagach1781 I think it's an electronic sensor error
Will the Xbox ones work on Xbox elite controller
Both the Elite Generation and the second generation work, but the Elite generation II installation is slightly more complicated.
How do you get into mode A?
Hi.
it works the same way for Xbox with your set (stick+board) ???
Yes, the xbox is just installed a little differently
Im having trouble getting it to enter the editing modes. It seems to always just load back in to the circularity test. Any help would be GREATLY appreciated.
Did you encounter a malfunction?
@junZeng-520 yes, I can't seem to get it to edit my settings
@@junZeng-520 I'm using a dual analog adaptive controller using 2 Sanwa JLMs. Will this method work for them? I can't seem to get any info on them as they aren't sold here in the US. Any advice you have would be GREATLY appreciated
@@fallonoverton1309this is for standard controllers. You're using an adaptive controller for cripples. Obviously it won't work
@Plaojuo yeah thanks for the generous comment d bag. The joysticks are both hall effect sensor joysticks, which is why I asked. A simple no would have been fine.
Do I require the driver board to allow me to calibrate an xbox controller like the video?
Yes
we really need a better video on this im still confused
Play around with it and you'll then understand it
Hello brother, you don't have to be confused, simply by pulling the joystick, and then turn on, he will enter different modes, you can adjust the center point of the joystick and external range.
@@1upnolan340how do you enter this adjust mode?
dose this work on the ps5
edge controller?
Where to buy for xbox one controller?
What if I enter those modes by accident while playing ?
You need to turn on the controller for a moment, your fingers do not touch the joystick. The program decides what it should do the moment it starts up.
@@junZeng-520 can I installed these for the Dualsense Edge controller ??
@@kevindesmond2120 My drive board doesn't support the edge controller, but some players have tried it and it's said to be fine. Better to wait until I come out with an EDGE-compatible version.
I'd love to do a review on your product, can you give me a link to your store? The calibration was amazing! Also which hall effect sensors would give me the best result? I have the orange ones which I did a review on. But I'm interested in the blue K-silver ones which I haven't tested.
蓝色的传感器结合红色的机械结构，简直完美。
I found your aliexpress page and just placed an order for PS5. I will take your advice. This seems very promising.
@@GregRosolowski I'll provide you with separate mechanical parts, which you assemble as needed
@@junZeng-520 Great job were to buy it ? Need Just pcb board to calibrate
@@Modyfikator Yes, we can sell the drive board separately.
This is perfect! Amazing job! Is there any jitter?
抖动很小，我的驱动电路板有降低噪音的程序。比ps4控制器055型号抖动都小。
The jitter is minimal, and my drive board has a noise-reduction program. Less jitter than ps4 controller 055.
@@junZeng-520 thank you, can it be overclocked to 1000hz polling rate?
Great video! What software are you using?
ya what program he's using..im waiting for his reply im planning to upgrade also my dualsense with these hall effect sticks
@@jedxyrusenterina4764 Hello, my friend. My black to drive circuit board inside with my program, the video inside the test joystick data is a test page. gamepad-tester.com
Hello, my friend. My black to drive circuit board inside with my program, the video inside the test joystick data is a test page. gamepad-tester.com
What is the app / site being used to do this test?
This is a website Gamepad Tester
Where will these be available?
pt.aliexpress.com/item/1005005918396855.html?gatewayAdapt=glo2bra
Hello friend, here is my link.
It isn’t possible to ship to Germany :( Is there any other way to get these?! I love this product. Your are brilliant !!!!
@@rubensonnentag6587 Hello, I have not obtained the authorization of the EU's packaging law, and after obtaining it, I can sell it to Germany.
@@junZeng-520 Do you know how long this will take ?
How to enter the mode
I do the same but i dont enter the mod
Sabes como se entra en los modos de calibración en los mandos Xbox?
with no explanation, and no reponse, this video is useless..
I cant enter adjust mode, any help?
Hello, are you having trouble? I'll help you
@@junZeng-520Can you please help me on how to get into a care allowance mode, the same as in Shamra?
I need help. Who can help me? Please reply
@@Al_mawheb You can check out some of my recent videos.
@@junZeng-520 Can you send me a picture of the welding equipment, please?
Are using a program to calibrate the joysticks? Cause the website to test does not hav that ability
He installed hall effect (magnetic) joystick modules + a specific PCB (I think designed by him) underneath the controller's PCB.
Did you put the wrong price on the pcb board? It cost 370usd each on aliexpress
Hello, no problem. See other links on my home page. This link is for custom pricing, which is not official.
will this work for ps3?
How to calibrate hall effect no jitter version?
how to buy this? you have shop at aliexpress?
pt.aliexpress.com/item/1005005918396855.html?gatewayAdapt=glo2bra
Anything for Xbox ?
My other video, on the XBOX controller, works just as well.
Accidentally fried my hall sensor doing this. Be careful or just don't touch em
should i just manually calibrate them after i install them to my controller board?
@@iv624 Yeah. Just plug it to the Laptop or pC
@@carloganz thanks
Como se llama el programa para calibrar los joystick?
El que está utilizando es gamepadtester pones eso en Google y te sale, es una página
no es un programa para calibrar es la pagina de hardwaretester
@@NicolasSilvaVasault pensaba que había que usar un programa pero resulta que al montar los joystick magneticos hay que montar también los driver de calibración que van también soldados, la página para calibrar los joystick ya la conocía pero para poder entrar en esos modos de calibración tienes que tener montado esos driver pcb, también voy a pedir en aliexpres el cabezal para soldadores t12 que te permite desmontar los joystick muy fácilmente y en un minuto, te ahorra mucho trabajo.
yo compre los naranjo hace poco, y si bien funcionan mucho mejor que los que usan potenciometro, calibrarlos es una patada en las bolas, porque tienes que hacer un juego entre el analogo y un punto al que insertar una aguja, y cuesta un monton porque a veces se te va, en cambio estos con el pcb la calibracion es milimetrica y no tienes que desarmar nada, pero la diferencia de precio es grande, $20 USD vale el par de estos @@MiguelAngel-ij1oh
No me entra en ningún modo, hay que instalar algún driver ?
@hyprcontrollers
my left joystick stuck in mode a, how do i fix it?
did i fried the board?
it was working will
@@ghkgfi9tyh429 rip
Is there a way to reset the settings and start over? After I calibrated, it won't let me get into different modes for the right stick. Please help.