Great video, clear, consise, and showed it being done. Didn't want to toss a otherwise perfectly good controller just because 1 bumper went out. Thank you !
Man I've salvaged these 2 controllers I've had for years now 😅. Bought space marine 2 today, went to hop on, and realized my LB was toast. Pretty sure my cat punted it off the table 😐. Anyways shout out to you because I have now salvaged my controller for the umpteenth time 🤣👍
Had a controller LB to be a lot tougher to push than RB. Opened it, saw it had slightly more tension, tried to change it with prier but I don't think I managed to do that. Gave up, put controller back in place and top buttons were stuck, like in the video and pressed the buttons harder and loud noise came. The LB button was no longer stuck and was really easy to press again. I think the case was slightly off and let the LT to push button a bit so it had more force against press. Easy fix without opening would be... keep your fingers on LT and RT and it relieves the tension anyway on bumpers.
My model 1697, the connect button is held down by the cover for the Xbox button, so when I took it off, the button went flying (who knows where, I cant find it now). After putting it back together, it glitched out my PC (had to restart it), but the controller is working now, so this tutorial did help me save $60 so I don't have to buy a new controller.
*_Once I put on the bit that goes over the guide button, the bumper side that happened to have broken off won't move and is just stuck._* Only way it'll work is if I leave that top-centre bit off. Can't see anything broken off or imperfect, so I'm baffled. Though it's a Venom make, so maybe some slight difference somewhere is enough.
Hey where did you buy this bumpers. I bought the ones advertised to fit controllers with a 3.5mm jack but they are different. This one u show is exactly like mines.
Can you give me the link I’ve been looking for over an hour the first one I ordered wasn’t even right for my controller didn’t fit into where it’s held in place.
Great video!! However, I do have one question. Will these instructions work as well with the xbox elite v1 controller model 1698? I know it's probably a dumb question but I just wasn't sure if my controller would be slightly different or not being that you're showing a standard controller in the video. My bumpers & triggers should be arriving in the next few days. Thank you for your time.
This sounds really dumb but have you tried pulling the triggers down to the board and then putting the back plate on? I found out that this was my issue after about 20 minutes and a smashed light
Keep having an issue where one of my bumpers is too loose and clicks annoyingly every time it's barely touched. Gonna try this in the morning and see if I can clean things out under there to fix the problem Edit: Can't find the exact issue other than it gets clicky when the back panel is on, but cleaning and putting things back into place seems to have negated a lot of it and the clicks are barely audible at the moment
can someone please help me ive had this roblem for a few days that the LB bumper looks just like it works but its stuck on the inside. i think its a glitch but i dont know if some one can help me that'd mean a lot!
Where does someone buy replacement bumpers? I have a Halo 5 controller and I need to replace the bumpers and while I'm at it I'll probably replace the thumb sticks, but I'd like to find replacements that match the color of my original pieces.
Need to replace the bumper set in general wondering if I could take a part normal Xbox one bumpers and put it on elite would it work or does the bumper set have to be elite? Plz reply asapp thanks heaps
![Jack Harlow - Hello Miss Johnson [Official Music Video]](http://i.ytimg.com/vi/Q86_nlRoIGw/mqdefault.jpg)
Thank you my friend. I’ve watched four different videos that did not take off the bumpers like I was trying to do.
Great video, clear, consise, and showed it being done. Didn't want to toss a otherwise perfectly good controller just because 1 bumper went out. Thank you !
So nobody’s gonna talk about how he put the battery’s in wrong? 😂 The guide helped though so thank you
Man I've salvaged these 2 controllers I've had for years now 😅. Bought space marine 2 today, went to hop on, and realized my LB was toast. Pretty sure my cat punted it off the table 😐.
Anyways shout out to you because I have now salvaged my controller for the umpteenth time 🤣👍
Had a controller LB to be a lot tougher to push than RB.
Opened it, saw it had slightly more tension, tried to change it with prier but I don't think I managed to do that.
Gave up, put controller back in place and top buttons were stuck, like in the video and pressed the buttons harder and loud noise came.
The LB button was no longer stuck and was really easy to press again.
I think the case was slightly off and let the LT to push button a bit so it had more force against press.
Easy fix without opening would be... keep your fingers on LT and RT and it relieves the tension anyway on bumpers.
great video!!!! i really loved the part where i could clearly see where to snap in the lb and rb replacement, oh wait… i couldn’t see it
Yea this didn't help with putting on the bumpers
great video, and always check your controller number first!
Great tutorial! Thanks for helping me
this helped slightly so u get a like lol
My model 1697, the connect button is held down by the cover for the Xbox button, so when I took it off, the button went flying (who knows where, I cant find it now). After putting it back together, it glitched out my PC (had to restart it), but the controller is working now, so this tutorial did help me save $60 so I don't have to buy a new controller.
Thank you😊
Thanks that helped a lot
*_Once I put on the bit that goes over the guide button, the bumper side that happened to have broken off won't move and is just stuck._* Only way it'll work is if I leave that top-centre bit off.
Can't see anything broken off or imperfect, so I'm baffled. Though it's a Venom make, so maybe some slight difference somewhere is enough.
I have the same problem
I guess I'm the only one who doesn't have one easy LB RB snap in controller..
Thank you
What kind of screw driver do you need mine isn’t working
The screwa have a little metal pin in the middle of each of them. Just get a drill with a small bit and drill it in the hole, and they pop out
Do your triggers still work?
When i put the middle cover on. The bumpers stop to touch the small buttons and they hard to push
Thanks
One of my triggers are even/ more up, what should I do?
Hey where did you buy this bumpers. I bought the ones advertised to fit controllers with a 3.5mm jack but they are different. This one u show is exactly like mines.
Amazon
Can you give me the link I’ve been looking for over an hour the first one I ordered wasn’t even right for my controller didn’t fit into where it’s held in place.
check your controller bumper design first,i have 3 different controllers with 3 different bumper designs
My bumpers won’t even click down when I put the middle piece back in ............ why is that happening ?
Please help me
Great video!! However, I do have one question. Will these instructions work as well with the xbox elite v1 controller model 1698? I know it's probably a dumb question but I just wasn't sure if my controller would be slightly different or not being that you're showing a standard controller in the video. My bumpers & triggers should be arriving in the next few days. Thank you for your time.
They should be similar enough to get by
Big brain
the big grey thing like litterally fell off and it was 2 wires on it ...
How can you replace the USB port? I have a broken one
I've never used the USB port on mine. What is it used for?
@@jeramybearamy8539 charging, updating controller, to use without batteries
My RB bumper just keeps getting stuck on the RB trigger no matter what I do
This sounds really dumb but have you tried pulling the triggers down to the board and then putting the back plate on?
I found out that this was my issue after about 20 minutes and a smashed light
@anonymous 565 you're welcome.
Even if that's sarcasm you are welcome.
@anonymous 565 well I'm glad I could help
Can this work for series s controller ?
Sorry if I’m to late but yes
How do you just pull the bumper off, I've taken it all apart but it's stuck, if I pull harder it feels like it'll break
Mine broke so now I gotta get a new one
Keep having an issue where one of my bumpers is too loose and clicks annoyingly every time it's barely touched. Gonna try this in the morning and see if I can clean things out under there to fix the problem
Edit: Can't find the exact issue other than it gets clicky when the back panel is on, but cleaning and putting things back into place seems to have negated a lot of it and the clicks are barely audible at the moment
when i had that problem i just popped the bumper out and then cleaned it and walah it worked again
its unlikely but u can look up a video for a fix with your model number which is behind your battery pack
everything else on the xbox one s controller is easier compared to the normal xbox 1 controller but the bumpers are way harder on the s
ive fixed computers replaced things and Aswell as controllers still nothing more frustrating for me lol
its nearly impossible to dismantle a controller i broke more then i could repair.
can someone please help me ive had this roblem for a few days that the LB bumper looks just like it works but its stuck on the inside. i think its a glitch but i dont know if some one can help me that'd mean a lot!
Where does someone buy replacement bumpers? I have a Halo 5 controller and I need to replace the bumpers and while I'm at it I'll probably replace the thumb sticks, but I'd like to find replacements that match the color of my original pieces.
Amazon has all the grey ones. Pretty cheap
Need to replace the bumper set in general wondering if I could take a part normal Xbox one bumpers and put it on elite would it work or does the bumper set have to be elite?
Plz reply asapp thanks heaps
I have the exact same problem ugh
@@jacksoniv6911 so annoying lol
Yes you can
The elite bumpers are a different shape i think. Search xbox one elite controller bumpers on amazon. They're the silver ones.
@@蓮90 cheers mate just ended up getting a new controller lol
It doesn't just "pop back in"
It really does but ok
Didn’t help. I wanted to completely remove the lb button to get to the broken spring
bro just buy a new controller
@@coleevans8749 na I fixed it using spare parts
How did u take the bumper off w out breaking it, I've flicked the latches up but I can't take the bumper off????
sup
I need help my PlayStation keeps going into safemode when I restart it it goes straight into black screen while its on and it does nothing
He has a vid for that
Xbox is for people that buy Xbox’s 🥪😠
Facts
Thank you!
Thank you 🙏