Simple and cheap to make. Pure hydrogen - Pure oxygen. HHO Hydrogen Generator. Electrolysis
HTML-код
- Опубликовано: 15 сен 2024
- Hello. As promised I came back with the promised video with the hydrogen generator that separates water from hydrogen and oxygen. This generator removes pure hydrogen and pure oxygen separately, so this hho generator is a separator. I used a 3D printer to get some parts much easier than making them from other materials. The walls of the generator are made of 10 mm plexiglass cut, drilled and shaped by me. The gaskets are made of 0.5 mm thick rubber. The stainless steel plates are made of laser cut 316L stainless steel. The surface where the electrolysis takes place is 100 mm in diameter, so the separators I took out of the 3 d printer have a diameter of 100 mm and a thickness of 5 mm. As you saw in the video, oxygen comes out on the right side and pure hydrogen comes out on the left side. For electrolysis I used distilled water and a little potassium hydroxide and as usual current from a 12 V car battery. The amps consumed were around 8-10 amps. We used 7 stainless steel plates, 4 of which were made to produce hydrogen and 3 to produce oxygen. You can use more boards if you want a higher production. I'm not going to use this generator for anything, I just built it to get an idea of how you can separate the two gases.
Thank you very much for your time and support, you are my success so don't forget to subscribe to comment and like!
Subscribe to / fantotzyy
• 8 Ideas. HHO Hydrogen ...
Do not forget!
👍👍👍Subscribe 👍👍👍👍
Hi, your work is perfect, as I once wrote.
But you have one mistake there. Plate No. 1, which you laid in the first assembly, has no effect, because it has no possibility to remove gas - it is blocked by a separator, which in the chasing part removes oxygen from electrode No. 2.
In my opinion, a separator must be laid as No. 1, which will remove the gas from electrode No. 2, etc.
Mistakes happen. Good luck
@@pitiwisi Dude, when it comes to hydrogen, you're not allowed to make mistakes. It has an exit through the pexiglas plate 😉
@@Inventive101 Wow, no! it's a mess!
It's like a car against a wall - a biased blind man
ok
I also have to buy a 3D printer, the work is faster.
My separator is not very simple and it is not so powerful.
Probably more chambers would be needed.
It will be OK with a 3D printer, but you will need to glue the upper part well after installing the electrodes.
I don't know how to send you a drawing, my email: protipol@gmail.com
Question sir,
Would it be possible to make a self-contained unit that you could say wear on your back or person, and use it to create oxygen for scuba, how much would you need to be able to breathe well. Could you breath that , or would it have to be scrubbed like threw charcoal or something?
Thank you in advance just curious
@@dirtwizard5647 I think he can breathe. it is pure oxygen. The problem would be that if you wanted to carry it on your back it would be very difficult. I don't know how many liters of oxygen a minute is needed to be able to breathe well
You did something that not everyone can do, an exceptional idea that everyone can understand
Thanks a lot 😉
Wow thanks a million for posting. Very kind of you Sir. This is the best I've seen. BRAVO
Thank you very much
I'm sorry, I got a little involved in PEM separation membranes.
I actually also have one generator this way, but simple. Plexiglass, three chambers and three electrodes in them. In the middle minus and on the sides plus. The two baffles in the middle end above the floor so that the ions can flow to the other electrodes. The gases are well separated. But your work is perfect. Congratulations
Thank you. It can be made even simpler than you have, it is easier to control. You really gave me an idea, that's what I'll do. Several generators formed from 3 plates then I will unite their result. simpler and easier to do. Thank you
Foarte interesant si util canalul. Foarte bine realizate montajele. Profesional. De asemenea ar fi utila o continuare. Despre modalitati de comprimare si stocare a gazelor rezultate. Si bine inteles, realizarea unei celule de combustie pentru conversia inversa. Succes. Urmaresc.
Great idea! Just a little observation, the main idea behind the dry cell design is to make the electrolysis process more efficient. But, using those plastic separators, the electric current can only pass through the hole where the water pass, so the current will travel from the edges of the hole to the edges of the other hole on the other plate. That makes resistance as the wet cell design does. Maybe I'm wrong, just a though. I wonder if instead of plastic, you use a neutral plate with just the borders in plastic so the current can pass through the neutral plate to the other plate. In this case a large area will conduct and produce hydrogen. Maybe putting some plastic or rubber on the edges of the holes where the water pass through will increase efficiency. Maybe not. Has to be tried.
The neutral plate takes current even if it has rubber edges. I think it can be done as you say, but it needs to be tested a little
Thank you very much
No it wouldn't work with a neutral plate (of metal). Because if current passes through it, that would mean that the reaction take place on it as well. So supposing you get it to work, you would simply loose the separation of H2 and O2.
Ideally the separator should be made of a material that allows OH- ions to travel through, as they carry the charges in the solution, so that they don't need to go all the way through the one hole at the bottom. I wonder if a piece of cloth would do the job, as it might stop gas bubbles once it's soaked up...
I think we can use nafion (a polymer) as a separator around cathodes since it doesn't allow electrons but only protons to pass through.
Simply beautiful just a bit of reading the comments getting some access to some tools and I bet with almost no education and no $ I could assemble something similar to what you have done thank you. And great job.
Thank you very much
Want to make a big unit to run a torch. Great build.
Sir.thanks Good job 👌 Sir 👍👌👏❤️❤️🙏🙏🙏
Thank you very much friend
Impresionant.Ai castigat un subscriber.Pana si orbii au inteles acum cum sa extraga hidrogen pur din apa. Mai clar video pe youtube cu privire la operatiunea asta nu exista. Tu la ce folosesti hidrogenul? S-ar putea modifica un generator care produce electricitate,ca in loc de benzina sa-l faci sa mearga pe hidrogen sau pe HHO? In afara de masini, in uz casnic ,nu s-ar putea folosi la nimic altceva.?Daca sunt idei , vrem si filmulete in directia asta. Iti doresc succes
Mulțumesc mult. Eu am pe mașina instalat un generator pt reducerea consumului, l-am făcut in urma cu 10 ani din curiozitate. Idei sunt multe, timp nu prea este dar incet incet o sa le fac pe toate. Numai bine!
This generator was created just to experiment, to give some ideas to those interested
This is a really clean idea and test model, I am curious if it would be more efficient if you built it smaller
Great videos, I did subscribe: here is a challenge for: can you make a hydrogen gas cooking stove?
Yes it is possible, thanks for the challenge! I like this! I'll make a video for you soon
a slightly larger project related to some batteries that are charged by the sun or by the power of the wind or by the power of the water. Is it allowed?
Perfect project
Thanks
You are doing a great job, keep it up, prayers and good wishes, I had a question, does it generate electricity, I will be glad bro.
If anyone needs sketches to write to me
Great, thank you!
Thanks 😉
Always the best!
Thanks a lot
How would you capture the gases and then store them for practical use? Can this be scaled up to be used in a home?
I have the same question. I’d love to use hydrogen as a drop in fuel for my gas appliances.
Real technology!
😉Thanks
Dexter's laboratory. Super interesant.
Excellent demonstration, very clear on how to make this all happen. Thanks I will be doing this ASAP!
Thank you, I send you the link with the sketches
ruclips.net/video/9vri9-rKa-I/видео.html
@@Inventive101 hallo
@@Inventive101Gibt es eine WhatsApp-Nummer, an die ich mich wenden kann?
Ella megale... mia xará mbravo! Xeretismata apo Brazilia!!
Ευχαριστώ πολύ. Χαιρετισμούς από την Ελλάδα αλλά δεν είμαι Έλληνας
@@Inventive101
Ουτε εγώ ✌😁
@@irgosum Από που είσαι?
@@Inventive101 Βραζιλία....
Αλλά γενιθικα μόνο....
Και μεγάλωσα στο Μεσόγειος και Αιγαίο
37 χρόνια Ιταλία, España,
Ελλάδα και άλλες χορες.
@@irgosum Καταλαβαίνω! Καλή τύχη φίλε
Super profesionist
Multumesc
Hi from France .. Well Hydrogen motor couple with petro-carbu motor ( one cylinder by two who's turn with hydrogene and second cylinder turn with petro-carbu ) ..
Like that , cylinder petro ignitate the current for needs ..
Nice work
Please how much hydrogen can the best pem electrolyzer produce per hour
Interestingly, the performance of devices with separate gas release is different from devices where a mixture of HHO is released?
Salutare. Cum lucrează iarna la ger instanță în automobil?
Felicitări! ... super tare
Multumesc foarte mult!
Come on friends, I need more subscribers, more likes
Fantastic
Thanks
For higher hydrogen production the power plates increase or add more
How much does it produce now?
That looks way better
Is there access to the details of your projects; dimensions, materials etc? Without easy, inexpensive access to the machining capabilities in order to create the parts for any project, my usual m.o. is to 'shop around'/dumpster-dive for parts to repurpose
They are not noted anywhere, only in my videos in some of the descriptions. If you are interested in something I can tell you anything.
Amazing video, but I didn't see the electric connections.. can you assist?
Yes, exactly what would you like to know? I used direct current from the battery here. I will use a relay now
Not Simple lol but looks cool
😁 Thanks 😉
Hook the output to a hydrogen gas analyzer and check the purity of it. It’d be interesting to see if it’s pure enough to be safely stored.
If the materials are what to say, the H2 should be a H2 only, I assume? What other impurities could be involved? Acetone maybe?😊
Super
Ms
I see other video which a person use PEM Electrolysis for making Hydrogen only (he trow away oxigen and other things beside hydrogen) and using compressor to compress it in a big gass tank. He always use hydrogen analizer to check how many percent hydrogen its produce. He said that if below 95% its dangerous because Hydrogen and Oxigen mix if pressured can ignite itself. If the not for storage it's ok not pure.
I also concern with the distance and seperation the positive and negative electrode. My experience more distance and more seperator of the positive and negative electrode the stream of electricity can flow in water drop dramaticly. So maybe more evicient making HHO because don't need to seperate it with plastic membran and the distance can very very near. In HHO Generator 1mm or 2mm is already diffrence in ampere.
Do you have diffrence experience or knowlede because i don't have experience with Hydrogen seperate with Oxigen in dry cell. I have try it before in wet cell. About the distance and the plastic seperator. What the ampere and voltage, what the diffrence with HHO Dry cell example with "+ n n n n n - n n n n n +" thank you.
as always very inspiring and intuitive
well done
Thank you very much sir Mohammad
Thanks
I made this system of dry cells with the separation of hydrogen and oxygen gases separately. I would ask you to look at my works, I am just a different material for membrane usability
@@hydrogenh2energy964 which video sir?
ruclips.net/video/Z1OC6Tx8Kzc/видео.html
Which kind of steel we can use for hydrogen cell
can you make a complete unit for sale? i don't have 3d printer to make parts. tell me what you would charge to make..
The material used for the printer cost $ 11. and the stainless steel plates because they are few were cheap 25 euros. I made the sketch for the printer myself, the hose and the plugs for a few more euros
No friend, I can't do it for sale yet, why do you want such a generator? it's not exactly the right one, it was created just for a demonstration
You rock! Keep going! ❤️❤️❤️
Thank you very much my dear ❤️
hhogenerators so cool
Please tell me - where did you get those small plumbing fittings?
What do you think should be changed about this hydrogen generator?
How much electricity consumption is required for one liter or kilo of hydrogen gas?
Hola. te felicito por tu proyecto!!!! muy profecional y limpio !!!! me gustaria saber si esta a disposicion de poderlo ordemar de tu empresa y cuanto vale? me gustaria comprar uno !!! gracias y espero tu respuesta. BENDICIONES Y MUCHO EXITO !!!!!
Bom dia
Como posso comprar um gerador de gases separados .
Sou Carlos moro no estado do Mato Grosso, Brasil.
Obrigado
Por enquanto, não estou fazendo isso à venda. Não sei como poderia mandar para lá
VERY unique and nice design. The only problem is that (and this goes for any electrolyzer that doesn't use solid polymer electrolytes) you may be able to separate the H2 and O2 but you cannot have ANY back pressure on those outputs at all. Try filling a balloon with hydrogen. Can't do it. I LOVE your design though. It's the best I've seen outside of PEM electrolyzers.
Thank you very much! I really can't put pressure on this generator, it could be stored with an engine but it's quite dangerous
Yes, but actually you can do a little vacuum for the collecting reservoirs😉 and do the compression/pressurizing later if necessary 😊
hello dear Inventive - water fuel . I am very interested in your project and would like to know where to download your drawings of the generator
What do you think about this device?
useful, easy to do. thank you
@@spirugrigore5165 😉
Good job sir!
Thanks sir
Good job!
Thanks
Welcome to my channel 👍🙏
Hi, my friend, what should Kate's voltage be
Can you please provide a complete report on it like why and when we use this or that
For me it was easy to do, for whoever it will be. I can help with the geographic scheme who needs it
Very cool! Thanks for sharing.
Can we add neutral plates in oxygen only
I'll experiment with that again
Do you have size specifications and build plans to pass on? I want to make one. I'm not paying these ridiculous fuel prices. I'm gonna install solar panels and a bank of truck batteries and use some of the free electric to split h2o into hydrogen and oxygen . Let a set of bellows fill up with pure hydrogen and when the bellows are full it switches a bsa air gun compressor on which will evacuate the bellows of hydrogen and compress into a empty propane tank. When full simply attach a regulator and pipe to the house gas line . Boiler and cooker will need jet size altering but all should run perfectly off hydrogen.
Πάντα ο καλύτερος!
Ευχαριστώ 👍
How do You know it doesn't mix?
I have a few more changes to make to this generator. I'll make a video with the exhaust gas setting it on fire, we'll see then
Bro next level 🙏🙏👍👍🔥
👍
Hello, thank you for the video, please tell me, do you have stainless plates not destroyed at all? I also bought myself several plates, when the current passes, Posotove plates seem to be destroyed, but slowly. I think I was deceived. Do you have any experience with this? Nobody on RUclips talks about this topic.
Very good job, thanks…
Question: do you think this cell could work with a solar panel as source of power?
interesting question. I am actually gonna try it but I am also curious about the answer indeed.
Did it work?
Hello firstly great video 👍🏻 secondly could you build me the hydrogen cell and how much please? If possible I’m sure there could be a way we could make contact. Thankyou 👍🏻👍🏻👍🏻
Corrosion question : How are the plates after a longer use ? I guess you're using stainless steel, so I wonder how it actually performs in such a basic solution, and with electricity flow. Because I know that in commercial electrolyser, nickel is used, which is also what makes steel stainless as it contains a certain amount of it.
Apparently I read from someone else not to use stainless steel. It can cause something that's dangerous. Can't remember, hexa something.
Hexavalent chromium was what he said.
@@thundergasaway6502 Hmm ok, that would not be great in fact..
I'd like someone to show how the electrolysers look later. Because there are many people showing there cells made of stainless steel, and then using a 12V power supply (😯 The reaction potential is 1.23 V !), but found no video about how the device get old...
Instead of steel, use a graphite film!😉
@@elfillari Hmm, I thought aboyt it but never tried.. wouldn't it fall apart over time ? And does it have an electrical resistance low enough.
My video is on the right track !! Thank you
εχω μια απορια ... ποσο καθαρο ειναι το οξυγονο και ποσο το υδρογονο ?
μηπως ειναι καπως μιξαρισμενα μεταξυ τους ?
πως θα μπορουσαμε να ξερωμε την καθαροτητα τους?
ευχαριστω
Δεν ξέρω ακριβώς πώς μπορείτε να ξέρετε την καθαρότητά τους. Τους έβαλα φωτιά και το υδρογόνο εκρήγνυται και το οξυγόνο δεν.
Bravo
Ms
Facut cu maiestrie, acum interesant ar fi cata energie ai consuma pt 1 litru de hidrogen? Am vazut intrun film de al tau aveai 7A la 12V si producea 0.75l dar cred ca era amestecat, H+O.
Great man
Thanks 🙏
🙏🙏🙏
How much voltage did you applied ?
It can be even simpler for those who can't get the printer
Foarte tare !!! De unde sunte-ți? Cam cat de mare trebuie să fie tot ansamblul și de câte plăci ar fi nevoie pentru un astfel de generator ca să scoată 5-6 l/min?
Salut si multumesc! Nu am facut foarte multe teste cu acest generator dar deoarece sunt foarte multi care ma intreba de el o sa revin cu rezultate
Sunt din Onesti dar Momentan locuiesc in Grecia
Hi, what brand of 3D printer do you run? Her work is very nice and what type of Filament is.
Thanks
Peter
Hi! Why we cannot see any wires? Power source?12v?KOH or NAOH in water? Concetration in %?
Wow nice.
Thanks
Nice project👍🏻 what’s the voltage, current, and LPM output of Oxygen of your setup?
A test has not yet been made with the current and amount of gas removed. I'll do it. Stay close
@@Inventive101 looking forward to it. 👍
what is larger cell you do, do you make one on 480 volt or 600 V?cubic neter mer minute what size can you go?
I will do in the future. now I'm a little busy moving to another country, actually to my own country
Electrolysis for everyone to understand
all my previous research has lead me to think that your setup should only be running at about 2 volts since you did not run your plates in series. could you explain what might be wrong with my thinking?
You kinda left out the part about the power supplied.
how many kwh to get 1kg of hydrogen?
I really appreciate your video and it provides a lot of info, I’ve been trying to see if you mention anything about your 3D printer but can’t seem to find anything, if you don’t mind me asking, what type of 3D printer do you have?
I don't have it, it's not mine, I don't know what type it is, I went to a workshop to make those dividers for me
What material do you use for separators - membranes?
Exactly what you saw in the video, plastic from the 3D printer
@@Inventive101 And that plastic as a barrier, does it belong to a kind of membrane that allows the ion to pass from the cathode to the anode, or is it just a plastic dielectric barrier for the expansion of gas mixing. The contact structure got into the cell through the bottom hole?
Is designing hydrogen generator your job? Just curious..
No friend, I'm working entirely on something else. Hydrogen generators is just my passion
Is HHO better or pure hydrogen better for fuel saving in the car?
I think hho is easier and more cost effective to use. The engine also needs oxygen. The separation process is more expensive
Hello, very nice device!
The working voltage is 12 volt, but electrolysis needs less than 2Vcc.
Do you have better results with 12?
Thank!
Thank you very much. I think the voltage is divided for each board
That is no possible because all boards are connected to battery. I saw some device that doesn't connect some boards that are called neutrals. With this configuration you are able to have voltage split, I understood...
Maybe less power consumption too!!! But I'm not sure...
Maybe you can test it connecting only two boards, first and last!
@@martinlopezA I could not put neutral plates on this generator to be able to share hydrogen with oxygen
@@martinlopezA If I connect only two plates or only some the voltage changes, I no longer have a safe division between hydrogen and oxygen.
How many of these to run a 454 big block? What power requirements also.
what is estimated cost for it
i would like to order a kit made of graphite plates for my Land Cruiser!
I don't make generators for sale yet. and I haven't made graphite yet, I'm waiting for a long time order from the graphite sheet to do some tests
subscribed, be waiting when you decide to make one for sale!
@@WaniMedia Good. thank you! I will say
@@WaniMedia Where are you from?
@@Inventive101 living in Japan, bought a freaking gas hog lol, still waiting on my chip before I do some hydroxyl boost mods on my petrol engine, did one before on a Diesel
Thanks for your support
Hi. I'm from Australia and would like to use this device for blowing balloons.
These balloons I will be using for fishing.
Do you sell the kit?
I don't have the time to create this meticulous project.
Hello, hope somebody can explain it to me. I think he is NOT sepereating H2 and 02. Between two steel plates is JUST ONE gas chmaber. But between two steelplates are 2 gases hydrogen and oxygen so i think he needs a membran to seperate those gasses so he needs 2 from his 3d printed gas chambers.
Hell yeah will be making a big one nice work.
👍👍👍
It’s either fake or they’re not showing something. Distilled water can’t pass a current alone
I love youuuu so much bayb❤
I have a question What did you use as power supply ? I couldn't see one ?