Это видео недоступно.
Сожалеем об этом.
AMP Research Powersteps Install (2014-2018) Silverado or Sierra
HTML-код
- Опубликовано: 29 июн 2018
- Help support the channel by using this link!
AMP Powersteps: Amp Powersteps (Silverado 2014-2018): amzn.to/2M8tA3C
Toyo RT Tires: amzn.to/2BfzSgm
Rough Country 3.5” Lift: amzn.to/2GlVUx7
Thanks for the video! Watching yours made me want to instal them myself instead of getting a shop to do them. Relatively simple but time consuming, a little bit of trial and error but not too bad. Love them. Thanks for the indirect encouragement!
I have the electronic steps that were factory installed. It was 1000 dollars for them. But it was already installed on the truck that I purchased. The only thing I have noticed is that sometimes the step doesn’t fold In when I shut the door.
Great instructions my guy..thank you
Great Video Dustin! I'm about to install mine this week, thanks for the video, you did well!
I bought this set for my brand new 2018 Ram 2500 Mega Cab
and they gave me fits to install them!
I followed the written instructions exactly to the letter.
Got all done, was all proud. Put power to them…
And the retracted up under the truck and wedged behind the pinch welds. I worked for hours putting brackets and
linkages on than taking them back off numerous times, I adjusted brackets and
linkages to NO avail. The boards jammed
up and got stuck under the truck every time to the point where I had to remove
the motors and pried them out from under my brand new truck scratching up the
AMP Research running boards. Decided to
call customer service. I called and
spoke with Brian Weaver. I explained my situation and he seemed to know exactly
what happened. Brian said “they got stuck behind the pinch weld right???” I
said Yep!!! He said with a snarky little
attitude “I’ll send you an email that’ll explain what to do”… So I get this email with an eight step
process to remedy the problem. I
followed that set of instructions to the letter again. Well step # 8 said if all else fails take a
hammer and bend the pinch weld seam over to make it fit. I tried but I would have had to bend that seam
over 45 degrees and I didn’t want to go that far with the sledge hammer. Long story short I had to take a 4” angle
grinder, remove ¼” + off the top of the pinch weld seam to get my new $1500 AMP
Research’s running boards to operate on my $70,000 brand new truck. Needless to say I was PISSED!!!! For that amount of money the AMP Research
product should have fit like a glove.
If you are looking to buy a set of nice power retractable
running boards LOOK SOMEWHERE ELSE!
Don’t spend your money here, You will be Disappointed !!!!!
PS… I took the AMP
Research badges off the steps so they don’t get any free advertising from
me. They better run flawlessly for a
long time… If they so much as hiccup I’m
going to unbolt them and throw them into the dumpster……. I’ll definitely let you know…….
I’m sold on em. Ordering some for my 17 LTZ.
Looks great. Can’t wait to get mine.
Awesome video bro!!! Keep up the great work
I just ordered these. How have they been holding up have you had any issues with them. Great video by the way !
How are these still holding up? I just bought the same set for my 2018 Sierra and love them.
Hey Dustin I hope all is well. I was wondering if the Amp Research running boards have been problem-free and if you would go this route again?
Yes I can honestly say I haven’t had a single problem, would buy day one for any other truck I had. And I haven’t received a penny from them to say this, they are that good!
@@DustinT Thanks buddy, glad to see your channel is growing, keep it up.
After installing steps they dont move when everything is hooked up.nothing happens when I open and close doors when I take motor off I open door motor turns counterclockwise wide when I close door nothing HELP
I see u said u didn't have to use the u nut because u have pre drilled holes already.
Did u drill them yourself or are they on there from the factory? Bout to install tomorrow on my 2016 silverado 1500 and don't really see were id put the u nut for the bracket
Good video but don't look as strong as the factory step side factory has 4 mounts on each side compared to 2 mounts on each side. Would love if these came with a few more mounts to hold more Weight. Just doesn't look like they would hold a lot of weight. Wouldn't want a friend that is overweight breaking them.
Sweet video and truck I got a 2018 gmc sierra 1500 4x4 double cab on June 11th
Do do you have any more Factory hacks you can sher with me
Great job....Awesome thanks
Can I run these on my truck that has traction bars??
No fender trimming? Called for in the instructions for the 2015 Silverado and Seirra.
I did not have to do any fender trimming on my pickup. Not sure if there is a slight difference in the 2014 and 2015
Hey Dustin, where did you run the wires from the passenger side to the OBD2 port?
Does the motors go in front
Or rear of truck and what side of the truck
Hi I recently Installed my amp power steps after watching your video and i followed all the instructions but my steps aren't going up at all i can hear the motor power when i open and shut the driver and passenger door but nothing happens any idea what it could be
Yeah, you screwed up somewhere. Go back and check all connections.
Great video! Thanks!
You bet buddy!
Nice job
Thanks
Where can I buy the obd2 plug and play conector ?
Great video brother! Keep up the good work.
Beautiful 😁👍👍👍
Does anybody know if these can be adapted to an 83 k20?
1ST!!!..U AND WALLIE B26 R THE 😎..COOLEST RUclipsRS
Hey bro the connection with the purple wires with obd2 connection come with the kit??
Hey man, yes this specific one does. But be sure to check when you order because they have a version that doesn’t (it’s older) that has to be hardwired into the door panel and it’s a bit of a pain. The obd2 version is much easier to install. Thanks for checking out the video!
JC... Where’s the GD dramamine???
Sorry man 😂
I Work For The Company Its In Tustin,CA
David Chavez that’s awesome man! You should see if they can hook me up with some swag for the free advertisement! 😂
Need more lighting my friend
I can't find the obd2 connection can you share link
The actual connection in the truck or the pig tail for the steps?
www.amazon.com/gp/aw/d/B00JE6P74K?psc=1&ref=yo_pop_mb_pd_title
But the obdII connection in the truck is underneath the steering wheel right around your left knee
What all did you purchase with the kit?
Hey buddy, all I had to buy for the job was this kit here amzn.to/2M8tA3C it had everything I needed to get the job done
I don't think you know the difference between nuts and bolts at 10:13 you called a bolt as a nut!!
He also said to torque the motors to 36 inch-foot pounds! 7:04
How much do these run?
Jerry Peterson i bought mine on amazon with obd 2 connection for 1400
Same here. Super easy to install.
@@albertoanaya1669 I can't find the obd2 connection can you share link
If you're going to make a video make a full one no skipping the install on the rear thumbs down
Audio stinks