Opel Corsa C ( 2000 - 2006 ) Intake Manifold / Removal / Gaskets Replacement

Here is a Playlist with more Videos about this Car :
• All Fuses & Relays fro...
A bad Intake Manifold gasket can trigger the following codes: , P0300, P0301. Basically, all these are showing a vacuum leak . So in this cideo you will see how to change the gasket on a Opel Corsa C 2000 -2006 . Engine code : z12xep
Disclaimer :
This youtube channel: "doit_vehicles " can not guarantee that this information suits your car . "doit_vehicles " assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk

[@train4905]

Dear sir.
I have just found your video.
Ive subbed.
This is invaluable to me.as ive got to replace my intake gaskets due to getting
P0300,p0302.codes..
Brilliant video.keep up the great work.
Thankyou loadsc,steve

[@HappyAlexandros]

I have the same engine. When unscrewing the oil filling cap, the cap lifts up by its own, instead of being sucked down onto the engine opening. Is this positive pressure inside the valve gasket normal? I thought inside the valve gasket there is a negative pressure.

[@simbad-4724]

Please can you tell me, where I should check for vacuum leak in this engine ? I replaced the gaskets, but now there is vacuum leak.

[@simbad-4724]

Hi, I'm tying to remove the same inlet manifold (1.0) but under that there are tied cables, and I'm can't to rotate it completely to remove. Can you tell me what to do ?

[@szantonorbert1113]

What is the instalation guide ? Dont have some video ? Very good video! Nice ! 👍

[@thedispenser8301]

Thanks!

[@clubcreativetoyconstructor5622]

Is it possible to disassemble intake manifold in two pieces and clean it, inside, with carb cleaner?

[@simbad-4724]

Finally done !

[@sib3865]

Do you happen to know if the process is the same for removing the manifold on a corsa D? Thanks!

[@doit_vehicles]

its gonna be very similar , however I never done this on a corsa d

[@sib3865]

@@doit_vehicles thanks was there a bolt on the underside for your car?

[@deborahcalis163]

I have the same car and i notist the it steers a little bit more heavy to the right than the left what could it be?

[@chazwalker7156]

My same problem was a snapped (front) suspension spring - good luck 🤞

[@dexietyy7922]

Can the intake manifold / twinport flaps cause a knocking noise on cold start for snoitb45 seconds

[@dacunha2436]

my intake is stuck i have taken off the bolts and the computer module i think maybe the wiring loom isnt off on the back but yeah...
its probs your chain tbh.

[@dacunha2436]

strip it down and see its must be a mechanical defect somewhere

[@teravolt6113]

Can a faulty intake manifold gasket cause a coolant leak on the Z series engines like this one? Thanks

[@doit_vehicles]

No

[@teravolt6113]

@@doit_vehicles Thanks. So one shall definitely look at the head gasket, EGR gasket and timing gasket if no visible leak is found around the engine bay (and the heater core isn't leaking) yet the level slowly drops when running.

[@doit_vehicles]

the coolant can leak through 3 points : external ( easy to be spoted ) internal into the oil channels ( easy to be spoted ) and combustion chamber ( hard to find ) for the last one an option is to remove the spark plugs and insert a tiny camera and check the cylinder walls for any water drops .

[@motospidey]

Doesn’t really show things in detail as expected. Like how you got the wire clip from behind off... I needed to clean the intake manifold a long time ago since it was never done. The car is now around 231.000 km and the engine is performing poorly since the manifold is full of carbon.

[@doit_vehicles]

Thanks for feedback

[@simbad-4724]

Sorry mistake. Trying

[@paulkomn946]

you mean that this manifold can be separated in two parts via the clips around it?