Fantastic addition to your growing business. 👏. Mike I've used your plug wire and will continue to. Super quality solid core wire cut to length and quality boots. With your new kits you take all the guess work out for the DIY crowd. Mike your turn around time is top notch. FAST SERVICE.
T-Mike - I have an Evinrude 1959 5 1/2 that hasn't probably ran since Nixon was Vice President. I changed everything coils, points, condenser, carb rebuild, paint, decals, impeller, gears EVERYTHING! Compression was about 70 lbs each cylinder with 2 pulls. Single line conversion. Can't start it by pulling handle so I use 1/2" cordless drill. Still won't start. Tried electric drill & VOILA it started! Only problem is I can ONLY start with electric drill - can't take it with me on the water - electric cord not long enough! Runs great and it can sorta idle but dies when lowest setting on tiller. I thought it might be a bad flywheel magnet but checked it and it's strong. No apparent leaks (head, muffler cover, valve plate). Please help! I'm solid grey - when I started working on this I was a brunette!
I love your videos. Quick question. What are the three bolt sizes needed to pull the flywheel off 1974 Johnson 40 horsepower? Think I need to check the points and maybe order some parts from your website. Thank you so much!
I used your tune up kit on the 1956 10hp Evinrude I’m restoring. Thanks for the products and videos. However, once I put the flywheel back on it partially rotates before it catches on the cam throttle control and won’t turn any further. Any suggestions?
Hey t mike I got a question you may or may not be able to answer. I have a older 25 evinrude I belive it's a 75 model. Some times il be running at wot and everything is fine. When I back off the throttle at a certain point my rpms shoot down to just above idling then when I try to speed up again it's like the motor just wont throttle up until it randomly decides to catch and then will run fine again at wot
Quick question,so my current coils have a nearly flush magnet on the top but my new ones have them sticking out and seem to be rubbing the flywheel,is there a real difference between the two? Just wondering if I can use either one
Added to my watchlist so next time I dive into my 58' 7.5 Evinrude, If it needs it I know where to go! Thanks!
Fantastic addition to your growing business. 👏. Mike I've used your plug wire and will continue to. Super quality solid core wire cut to length and quality boots. With your new kits you take all the guess work out for the DIY crowd. Mike your turn around time is top notch. FAST SERVICE.
Great videos-always enjoy no matter what the topic. Suggestion: add drink coasters to your merchandise, your logo is the perfect shape!
I literally just bought this off your store. Im excited as my new motor has a bad coil and I'm dying to get it on the water.
Great. Thx for the purchase. Let me know if I can help.
@@michaeljsimon will do and thank you so much for your videos and knowledge I love what you do
Love your work and passion mate, outstanding.
T-Mike - I have an Evinrude 1959 5 1/2 that hasn't probably ran since Nixon was Vice President. I changed everything coils, points, condenser, carb rebuild, paint, decals, impeller, gears EVERYTHING! Compression was about 70 lbs each cylinder with 2 pulls. Single line conversion.
Can't start it by pulling handle so I use 1/2" cordless drill. Still won't start. Tried electric drill & VOILA it started!
Only problem is I can ONLY start with electric drill - can't take it with me on the water - electric cord not long enough!
Runs great and it can sorta idle but dies when lowest setting on tiller. I thought it might be a bad flywheel magnet but checked it and it's strong. No apparent leaks (head, muffler cover, valve plate). Please help! I'm solid grey - when I started working on this I was a brunette!
Sounds like weak spark. When you increase the pulling speed it increases spark level. Check spark for 1/4” gap with the tester I use.
Great video Mike, someone was asking about german made coils. My Evinrude has a couple on it which was surprising, but I heard they are pretty good.
Another great video Mike. Sending you good wishes on your move !! Godspeed & God Bless,
Sincerely ............
Cool be in the market soon.
I love your videos. Quick question. What are the three bolt sizes needed to pull the flywheel off 1974 Johnson 40 horsepower? Think I need to check the points and maybe order some parts from your website. Thank you so much!
How much for a coil,points,and etc plate ready to install
I used your tune up kit on the 1956 10hp Evinrude I’m restoring. Thanks for the products and videos. However, once I put the flywheel back on it partially rotates before it catches on the cam throttle control and won’t turn any further. Any suggestions?
@@brellavideos3850 yes your coils must be rubbing on flywheel / did you use a coil locator ring to position coils correctly?
@@michaeljsimon no sir. I’ll give that a try. Thanks.
Hey TMike I love your videos. I have a 59 18hp golden jubilee. Will your kits fit that?
Yes
Hey t mike I got a question you may or may not be able to answer. I have a older 25 evinrude I belive it's a 75 model. Some times il be running at wot and everything is fine. When I back off the throttle at a certain point my rpms shoot down to just above idling then when I try to speed up again it's like the motor just wont throttle up until it randomly decides to catch and then will run fine again at wot
Sounds like one cylinder is losing spark. Try changing points. I sell the tuneup kit.
I have a 1954 Johnson 7.5 does not fire how much for ready to install magneto
ruclips.net/video/gEOISADZEhs/видео.html
Would this work on a 1960s model mercury 20hp???
Sorry. No
Quick question,so my current coils have a nearly flush magnet on the top but my new ones have them sticking out and seem to be rubbing the flywheel,is there a real difference between the two? Just wondering if I can use either one
@@Youza899 depends on the model of your motor
@@michaeljsimon on a 56’ 5.5 seahorse
@@Youza899 these coils should work
Would this kit work for a evinrude model 3034?
@@stevie8842 yes.