How to Repair Project Parts with Scarf Joints | Woodworking

Поделиться
HTML-код
  • Опубликовано: 13 дек 2024

Комментарии • 25

  • @GregWallis
    @GregWallis 6 лет назад +1

    Seriously impressed with that result.

  • @dleivam
    @dleivam 6 лет назад +7

    I loved the video.. very calm, not like many videos today where the host is in a hurry or on speed.

  • @chm1701
    @chm1701 6 лет назад +2

    Great video and he seems like a nice guy too. Well presented, clear information and a very handy thing to know. I'd heard about a scarf joint, but I had no idea that it was this. Thanks.

  • @jbb5470
    @jbb5470 6 лет назад +1

    Great video Ernie! I actually have a few short pieces that I need to make longer ones. This video came along at just the right time!

  • @ricardoartesao
    @ricardoartesao 5 лет назад +1

    Absolutely fantastic. Congratulations and thank you very much for showing this!!!

  • @kaleoariola
    @kaleoariola 3 года назад

    Mahalo for showing that easy jig

  • @toastersock
    @toastersock 6 лет назад +1

    Excellent thanks!

  • @scrimperuk
    @scrimperuk 6 лет назад +2

    Very informative video, thank you.

  • @thomaszaccone3960
    @thomaszaccone3960 6 лет назад +1

    They made extensive use of scarf joints in old sailing ships to joint long timbers in the keels, keelson and ribs among other areas, reinforcing them with treenails, bolts and wedges. This is a nice example of scarfs in fine woodworking.

  • @hassanal-mosawi6049
    @hassanal-mosawi6049 6 лет назад

    Thanks for sharing and showing that

  • @Uncle_Buzz
    @Uncle_Buzz 6 лет назад +1

    Half the guitar necks ever built are made with scarf joints. It's a great joint, even if it is mostly end-grain...though a real suck egg mule to clamp. Good tips! Merry Christmas! Chris.

  • @sylvainroy5764
    @sylvainroy5764 6 лет назад +1

    Thanks for the very informative video. Is there a rule of thumb as of at what angle the cuts have to be made?

  • @Myrkskog
    @Myrkskog 6 лет назад

    Handy tip.

  • @robertoler3795
    @robertoler3795 5 лет назад

    well done Sir

  • @telosfd
    @telosfd Год назад

    Asking, what is the length of the cut in relation with wood dimension?

  • @noeluisbarrantesvarela9474
    @noeluisbarrantesvarela9474 6 лет назад

    muy bueno

  • @patrickkinney4998
    @patrickkinney4998 3 года назад +1

    How would I do let’s say two 1x4 planks?

  • @shaineriches4369
    @shaineriches4369 2 года назад

    I would have inserted a piece of doweling through the scarf joint with the grain pattern going the same direction. It gives added strength to the joint and is hardly noticeable if done correctly

  • @garvielloken3929
    @garvielloken3929 3 года назад

    Nooice!

  • @presidentgateway
    @presidentgateway 5 лет назад +1

    The carpenter did not mention what angle to cut for good strength. Probably the angle for a thick piece like a table leg, where compressive strength is needed, is not the same angle for strength for long thin pieces that have to have bending strength, as for a boat gun'l. A little more technical information would have been useful.

    • @wholegrain27
      @wholegrain27 3 года назад

      He did say the longer the joint the better.

    • @BobHUK
      @BobHUK 2 года назад +1

      I've found the ratios needed as a very minimum. They are 4:1 for something like a plank, 6:1 or 8:1 for a boat keel, and 12:1 for spars of any kind, such as sail spars of wing spars in an aircraft.

  • @michaeljohn8905
    @michaeljohn8905 8 месяцев назад

    Thanks for this sir.