Hello! Wonderful video! Thank you very much! You're a great teacher. One year ago I didn't even have a driver's license and knew nothing about cars, but thanks to people like you, I found a new hobby. Just one question. On the 12 minute mark, you said that you already showed how to remove the pulley above the water pump. I've tried looking for that video where you do, but I've not found it. Can you please tell me where you show that procedure? Muito Obrigado!
Thanks so much for sharing all of your knowledge. One question for the camshaft seal that you are removing with a srewdriver. Why not using a small screw that you screw inside the seal and then pull it out with it. Thank you.
Hello. Yes you can and do that. And it will appear here on the channel too. But that method doesn't always works and it can damage the shaft or housing. So, I only do that in last resort
Hello, I just bought a Fiat Stilo Multiwagon 1.9 Multijet 8v 120. I'm going to change the distribution and I'm wondering whether to remove the manifold and clean it. The car has a hard time starting when cold but I have the feeling that it is a problem with the diesel returning to the tank since if I turn on the ignition three or four times it starts fine. what do you think? Do I remove the collector? Does it get very dirty in 8v? thank you!
@@alfaromeonoproblem i think The problem is when i stop tbe engine diesel return to The tank. If i put The contact two times for electric pump of The tank generate pressure, The engine start very fast at first atemp. If i only put The contact and them try to start, The engine turno about five seconds before start. Have the fuel pump unit of The tank any non return-valve or similar sistem?
@andresfernandez-dz2se yes, the injectors leak out.. there is no need for a check valve. The system having the fuel tank pump will blow out all of the air
I'm sorry, can I ask you a question? then it is normal after having inserted the pulley back into its joint that it moves a little if you turn it with your hand but without inserting the pin yet, because I noticed this and I had a doubt, then after tightening the pin it doesn't do more
@alfaromeonoproblem so the crankshaft pulley has this play or not because once inserted it also has a bit of movement on the right and left, I don't know if it's normal or it must be still, can you tell me something thanks for the precious answers my friend
Hi,Alfa!I have a question,is there anything specific and special when changing valve cover gasket?I heard from other brands like WV and Opel and etc. that there is a special way of doing it so you don't damage the seal and making it leak.And only thing that comes to my mind is torquing the bolts and torquing them in cross pattern like a head.Otherwise,great tutorials,very informative and helpful!
@@alfaromeonoproblem ... Thanks I will. I removed 4 injector and used DTI for TDC and set cam timing and now it starts first kick. I have a blocked catalytic converter and leaking turbo to fix. What I would like to know is , does the 120HP engine have swirl flaps in the inlet manifold ? The engine is choking .
Sei un grande ti volevo chiedere per la mi 147 del 2002 1.9 Jtd 85kw 287mila km o un problema su masima velocita ( a 170 bloca non va oltre tipo 3600 ,3700 giri circha o provato pulire egr valovola,corpo aria ,sensore egr sensore debimetro , la mia domanda e po esr la turbina? grazie,thank,blagodaram
@@alfaromeonoproblem my problem is speed bloced in 170kmh im washing egr ,sensor air colector not result problem thanks (turbo???) users oil silenia 10 w40
@comandodelta9267 hello. Do you have a remap on it? If not you can easily check out data and see what is missing. I do have a playlist for that kind of issues
I would never put paste in the sprocket, it's not the key what holds it in place (It's just for alignment), but the tightening torque making sprocket and cam surfaces to stick together. Adding paste reduces grip, I woudl not be not confortable with that.
Hola buenas, tengo un problema con el alfa code en mi alfa gt 1.9jtd 150cv. No hay manera de arrancar, centralita no deja quitar el alfa code . Te agradecería ayuda 🙏🏼
Olá. Posso falar em português, or can speak in English. Fazendo um diagnóstico a todas as unidades de comando, qual delas não responde? Doing a full diagnosis on all control units, is there any that doesn't communicate? I also have my Portuguese channel if it's better for you
@@alfaromeonoproblem Good afternoon Master, the original Computer, let everything work, try to boot. But it says (Alpha Code) and a key. I bought another computer, with the same code and took it to a technician. He told me to copy it and let's see..
Ok. Having the immo light on doesn't mean a problem with the key necessarily. If the esp or the ECU or the bcm are not responding at diagnosis it will do that. Can you confirm that they are present and if they have fault codes?
@@alfaromeonoproblem What I’m having actually is a problem with the diesel engine mount, I’ve changed it several times but unfortunately after a few drives and it’s even worse then the original one which was 18 years old 😅
Someone has a problem where the locking pin keeps breaking on the crnkshaft pully on the 2.4 JTDm in 159. They said it broke 3 times in 4 months. And sine a month and a half ago, the wngine runs badly and is hard to start, because timing went off by a coupple of degrees. And the engine is remapped, with the same map that is on like half of thise engines in Montenegro, and hw said they all run fine. I wonder what could cause this?
Hands down the best timing tutorial I've ever seen on any car on RUclips
Wow! Thanks for watching! Feel free to share with your friends. I have a playlist for timing chains and belts on the description below
Yes i agreed best tutorial on ytube explained clearly this timing is not complicated with you, cheers
Superb video and commentary! Thank you!
Thank you very much for watching!
Hi thank you for the detailed explanation. At 45:22 you mention the 13 mm bolt has an adjustment, what exactly do you mean? Regards, Wim
Hello, thanks for watching. The back of the bracket as an adjustment, on the hole were said bolt goes
Hello! Wonderful video! Thank you very much! You're a great teacher. One year ago I didn't even have a driver's license and knew nothing about cars, but thanks to people like you, I found a new hobby. Just one question. On the 12 minute mark, you said that you already showed how to remove the pulley above the water pump. I've tried looking for that video where you do, but I've not found it. Can you please tell me where you show that procedure? Muito Obrigado!
Hello. Thanks for watching! On my description there's a playlist with all the timing videos.
On the one for the twin Spark you get more info
Loving these meticulous videos.
Thank you very much for watching them!
Thanks so much for sharing all of your knowledge. One question for the camshaft seal that you are removing with a srewdriver. Why not using a small screw that you screw inside the seal and then pull it out with it.
Thank you.
Hello. Yes you can and do that. And it will appear here on the channel too. But that method doesn't always works and it can damage the shaft or housing.
So, I only do that in last resort
Excellent tutorial. 👍🏻
Thanks for watching!
Bro thanks so much for the video clips you filming. Greetings from Serbia
Thanks for watching them
I was thinking to use continental belts, and ina pulleys and metelli water pump. And what is the torq spec for the cam puley. sry i dont have autodata
Hello. It's good brands, if they are not from autodoc. 110nm on the cam pulley bolt
@@alfaromeonoproblem ty 25nm for pullyes and tensioner?
@VLOGISGARAGE for the tensioner yes. For the pulley the 8mm version yes, the 10mm bolt a bit more. Like 40
@@alfaromeonoproblem thank you
Hi very impressive videos. Please can you do video on oil pump replacement 1.9 Thank you
Hello. I do have two videos that have the disassembly of them. On the twin Spark and on the 8v JTD. But no, I do not have yet a replacement, sorry.
Hii! Thank you for the great video! Are these tips relative to 2,4jtdm 16v too?
For the 2.4 20v I have another video. It's down on the description on the timing belts and chains playlist
Hey Bruno, is there a way to time the injection pump that has no key?
Hello. No timing needed at all, even the ones that have key
Are crankshaft and camshaft bolts normal right hand or left land thread?
Hello. Only the crankshaft one is left hand threaded.
Thank you
Hi, what happens with a screw on camshaft when you put locktite on?
Hello. Loose the ability to shear the cam key in case of an issue.
What brand timing belt do you recommend if there is two option. Dayco vs Continental? :)
Hello. Dayco all day long. It is the original supplier. Also continental not always have good tensioners.
Hello, I just bought a Fiat Stilo Multiwagon 1.9 Multijet 8v 120. I'm going to change the distribution and I'm wondering whether to remove the manifold and clean it.
The car has a hard time starting when cold but I have the feeling that it is a problem with the diesel returning to the tank since if I turn on the ignition three or four times it starts fine.
what do you think? Do I remove the collector? Does it get very dirty in 8v?
thank you!
Hello. Thanks for watching. Bad start normally is the injectors.
Those intake manifolds are not very bad, live it be for now
@@alfaromeonoproblem i think The problem is when i stop tbe engine diesel return to The tank. If i put The contact two times for electric pump of The tank generate pressure, The engine start very fast at first atemp.
If i only put The contact and them try to start, The engine turno about five seconds before start.
Have the fuel pump unit of The tank any non return-valve or similar sistem?
@andresfernandez-dz2se yes, the injectors leak out.. there is no need for a check valve. The system having the fuel tank pump will blow out all of the air
@@alfaromeonoproblem Do you know the maximum correction value (mm3/iny) for these injectors?
@andresfernandez-dz2se 0.25
I'm sorry, can I ask you a question? then it is normal after having inserted the pulley back into its joint that it moves a little if you turn it with your hand but without inserting the pin yet, because I noticed this and I had a doubt, then after tightening the pin it doesn't do more
Yes. The play is there so you can adjust the tension of the belt
@@alfaromeonoproblem ok thank you so much my friend 👌😉
@alfaromeonoproblem so the crankshaft pulley has this play or not because once inserted it also has a bit of movement on the right and left, I don't know if it's normal or it must be still, can you tell me something thanks for the precious answers my friend
@tommasodanea5780 hello. Only the camshaft pulley has this movement
Hi,Alfa!I have a question,is there anything specific and special when changing valve cover gasket?I heard from other brands like WV and Opel and etc. that there is a special way of doing it so you don't damage the seal and making it leak.And only thing that comes to my mind is torquing the bolts and torquing them in cross pattern like a head.Otherwise,great tutorials,very informative and helpful!
Hello. Nothing to special about them. Apart from the drops of rtv and making sure the seal fits well.
And like.you said, beware of the torquing.
Gosh thanks, you would make a great instructor.
Thank you very much for your support and for watching. Please share the video or the channel
@@alfaromeonoproblem ... Thanks I will. I removed 4 injector and used DTI for TDC and set cam timing and now it starts first kick.
I have a blocked catalytic converter and leaking turbo to fix.
What I would like to know is , does the 120HP engine have swirl flaps in the inlet manifold ? The engine is choking .
Hello. No 8v that I know of have swirl flaps. The use of that is to cover one of the two intakes on 16v ones.
@@alfaromeonoproblem Thanks mate I appreciate your help
nice video just ceep going
Until 2025 I have videos every week.
After that too, but if the channel doesn't grow until there... I really will think about ending it.
Good since the high pressure fuel pump is non adjustable bcoz the fuel injector controlled by ecm as regular gasoline fuel injection
Sei un grande ti volevo chiedere per la mi 147 del 2002 1.9 Jtd 85kw 287mila km o un problema su masima velocita ( a 170 bloca non va oltre tipo 3600 ,3700 giri circha o provato pulire egr valovola,corpo aria ,sensore egr sensore debimetro , la mia domanda e po esr la turbina? grazie,thank,blagodaram
Hello. Can you translate to English or portuguese please?
@@alfaromeonoproblem my problem is speed bloced in 170kmh im washing egr ,sensor air colector not result problem thanks (turbo???) users oil silenia 10 w40
@comandodelta9267 hello. Do you have a remap on it? If not you can easily check out data and see what is missing.
I do have a playlist for that kind of issues
@comandodelta9267 check this out:
ruclips.net/p/PLgcTCigdgD8PRomJp2e6DXqrPeNnb6jSX&si=ixBSSdnMVlq4cL7U
I would never put paste in the sprocket, it's not the key what holds it in place (It's just for alignment), but the tightening torque making sprocket and cam surfaces to stick together. Adding paste reduces grip, I woudl not be not confortable with that.
Hello. The correct type of lube will work. It's been working for the last 20 years for me and my mechanics
Hola buenas, tengo un problema con el alfa code en mi alfa gt 1.9jtd 150cv. No hay manera de arrancar, centralita no deja quitar el alfa code . Te agradecería ayuda 🙏🏼
Olá. Posso falar em português, or can speak in English.
Fazendo um diagnóstico a todas as unidades de comando, qual delas não responde?
Doing a full diagnosis on all control units, is there any that doesn't communicate?
I also have my Portuguese channel if it's better for you
@@alfaromeonoproblem Good afternoon Master, the original Computer, let everything work, try to boot. But it says (Alpha Code) and a key. I bought another computer, with the same code and took it to a technician. He told me to copy it and let's see..
@david7477 when you turn on the key do you have the engine light? It's a 147 or 156?
@@alfaromeonoproblem Hello, good afternoon, the engine light is on, but it already had it before it failed. It is an Alfa Romeo Gt 150cv Diesel
Ok. Having the immo light on doesn't mean a problem with the key necessarily.
If the esp or the ECU or the bcm are not responding at diagnosis it will do that. Can you confirm that they are present and if they have fault codes?
Verry useful and educational video!! 👍🏼💯
If it is possible, I would like to ask about very common problem on most diesel alfa’s out there. 🙂
Hello. Take a pick at the description below, I have a lot of links for videos that may be what you need
@@alfaromeonoproblem What I’m having actually is a problem with the diesel engine mount, I’ve changed it several times but unfortunately after a few drives and it’s even worse then the original one which was 18 years old 😅
For engine mounts use only original ones or impergom
Someone has a problem where the locking pin keeps breaking on the crnkshaft pully on the 2.4 JTDm in 159. They said it broke 3 times in 4 months. And sine a month and a half ago, the wngine runs badly and is hard to start, because timing went off by a coupple of degrees. And the engine is remapped, with the same map that is on like half of thise engines in Montenegro, and hw said they all run fine. I wonder what could cause this?
Something hard to turn. Camshaft, hi pressure fuel pump,
Also wrong torque on bolts
Algo a wrong crankshaft pulley and a failed alternator pulley
@@alfaromeonoproblem Thank you. I will pass him the info.
3:05
Do you have a question?
Oh, friday uploads now? :-)
It was yet another mistake... but this time I did not change it. No worries, it's going well
@@alfaromeonoproblem Oh, right. Sometimes it is better to leave it, not to ruin the views.
👍