Tech Tip: NGK Spark Plugs!
HTML-код
- Опубликовано: 12 май 2021
- Please Like, Comment, and Share. Be sure to subscribe for future videos. Don't forget to hit the bell icon for notifications. RUclips has changed what they show subscribers!
#SubaruSambar #Tools #MrSubaru1387
Subaru Specialty Tools - www.amazon.com/shop/mrsubaru1...
Subaru Head Gasket Essentials - www.amazon.com/shop/mrsubaru1...
Subaru Timing Belt Essentials - www.amazon.com/shop/mrsubaru1...
StoreFront - www.amazon.com/shop/mrsubaru1387
If you like the vids and want to help make more: paypal.me/MrSubaru1387
----I assume no liability for property damage or injury incurred as a result of any of the information contained in this video. I recommend safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond my control, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not myself.---- Авто/Мото
For any doubtful peeps... ngksparkplugs.com/en/resources/5-things-you-should-know-about-spark-plugs
I literally just did this... now what.
@@snes06 If it were me, I'd pull them back out, clean the threads, and then reinstall them. I know it's a huge pain, but if @MrSubaru1387 says to do it I'd go through the trouble.
Thanks, I have an 05 legacy 2.5 non turbo, and it's giving me lots of problems right now ¿
@@snes06 I used to put antiseize on the plugs and the disgusting mess it left on the plugs and on the plug hole threads when the next plug change came around. Not good for electrical grounding and probably doesn't help the heat rating either.. Last time I changed the plugs after watching this video I sprayed starting fluid down the spark plug pipe holes to loosen the carbon and build up and used an air gun to blow out the crap. After a few goes and screwing a clean spark plug in to see if there was still residue I got pretty much all of it off. I also used a cheap camera bore scope to check the results and it was pretty clean after about 3 or 4 goes. And if you do it make sure the engine is completely cool. I'd be getting that crap off there, the torque can be 20% more than it should be due to the reduced friction with possibility of breaking threads and it's bad joo joo for an alloy engine. As Mr Subaru says, do it right, one and done.
I actually work for NGK, and I endorse this message.
Thank you for sending me spark plugs so that I could get my car running again. I don't understand why people have issues with NGK, they've worked great for me so far!
Can y'all lower the prices back to what they were in 2020 ? 😆
Can this fit my Chevy Cruze Ltz 1.4L?
@Therealgame1 NGK is a brand, they make a specific model for your engine.
@@yung_megafoneI don’t think anyone does at least in the the Japanese car communities. Ngk or denso is what they use as oem.
I feel like I just got scolded by the school principal
Would be nice if they printed it
on the box. Nothing much, just a short “do not use anti-seize”
They do
@ashishpatel350 they do not. If they do its only on certain boxes. I have caes of multiple different cr plugs not one says it. 😂
@ashishpatel350 they do not. If they do its only on certain boxes. I have caes of multiple different cr plugs not one says it. 😂
They spell it out in their install instructions. But then again, Honda's service manuals call for NGK plugs and call for anti-seize and provide a torque spec. So who is right? I suggest both are right as long as the fastening torque is adjusted accordingly.
Also make sure your NGK plugs are authentic.
I've been changing my own Spark Plugs since the 1970's when the gas was leaded & changing the plugs was a part of normal, regular maintenance. Spark plugs always had to be changed on the lawn mower, snowmobile, & motorcycle as well. I never used "anti-seize" on any of them. I have seen other videos on changing the Subaru plugs & often the "Backyard Mechanic" will use the anti-seize when changing them. My advice - Watch Mr. Subaru & go with what He says. I wish He lived in Vermont!...
So just a tiny bit then? Got it!
NONE
😂
Well I already put anti seize on my NGK iridium’s when I swapped the plugs in my LS400 1UZ (because I’ve always used anti seize), now I will know for the future and when I do the spark plugs on my GS300 2JZ, not to add anti seize.
I just wish I came across this video sooner because I had no idea 😅
My car runs great though! So as long as they will be good I will change them again early in 30-50k miles and correctly so it then.
What does Toyota's service manual say?
@pdubsyyyy I don't have the GS anymore I have a civic Si now, but I have my 93 LS400 still and it runs perfectly fine still.
Wish I came across this last week 😂
So I take it that is a no on the anti-seize...
Yeah for NGKs
Thanks for the video, I previously worked at a Honda dealer and they forced us to put anti seize on spark plugs. I had to fight back and print out the ngk tech bulletin that says not to do that.
We switched to graphite spray as online showed that this is what aviation industry used. But as well we sold a spark plug service and ngk said that wasn’t recommended because you can’t replace the crush washer
Well I fucked it. I put anti seize on my NGK spark plugs in my Sambar last summer. Oops. Perhaps two wrongs made a right since I didn’t use a torque wrench anyway 🙁😭😝
💀
It's OK, some issues can fix itself or can be pushed under the bed so no one will ever notice 👍
Dude so did I!
Thats krazy I been using ngks for years and have been putting anti seize 😬
Clear and direct video of the day 👍
Newer plugs are nickel .
When aluminium heads were becoming more common , there was a problem with steel plugs , and many people used antiseieze.
No longer necessary or recommended .
For what years though?
@Sum Teng Wong if spark plugs are not silver looking, ie steel not nickel , use antiseize if head is aluminum.
@@inverseuniverse5727 just did mines today, and hour it took. It's silver, it's weird cuz when I turn it, it stays firm for a while and I can keep turning it a lot more and I'm afraid to turn more in case it cracks.
@Sum Teng Wong slowly go out and in , 1/16 of a turn at a time with wd40 ..
I do because I live in Florida. I've had multiple seized plugs from the nickel corroding and getting stuck.
And check your gaps, which NGK also states to do as well.
Actually, there is a percentage that has to be taken away from the torque when you use anti-seize on threads. I believe it's somewhere between 10-20% you dock away from the dry thread torque. Coefficient of friction, simple Google search will point you in the right direction. As far as NGK having a special coating, I don't know because I don't run their plugs. But in the 10 years of turning wrenches professionally, I've never had any issues using copper based anti-seize on the threads of the plugs.
Y’all are torquing your spark plugs?
Hand tight plus hit it with the impact for good measure. XD
Anti seize is mostly aluminum so unlikely to be an issue with conductivity.
Honda's service manual specifically calls for NGK plugs and specifically calls for antiseize.
Is it an aluminum block? I'm unaware
@@steveeab2364 Yes. Aluminum head.
Curious
@@IShould.veKnown Iridium NKG plugs, a small amount of anti-seize, and torque to 13 ft-lb. That's Honda's stardard recommendation. Their torque spec accounts for the anti-seize. If you didn't use anti seize, and stuck with Honda's 13 ft-lb then it would be not tight enough. (NGK have a whole other service bulletin related the problems of not tightening spark plugs enough. Apparently they'll overheat in that case, and cause misfires.) NKG recommend no anti-seize and give an angular tighting spec. Either should result in the correct tightening IMO. And copper/graphite/aluminum anti-seize is irrelevant insofar as conductivity is concerned. All are good conductors. Without measurements and evidence I just don't buy that it affects resistance significantly. Especially when the plug itself already has 5k ohm of resistance built in. Personally, I follow Honda's spec because I've never seen any evidence that it's wrong. I also like the insurance it provides when it comes time to remove the plugs years down the road.
@@jptrainor Thank you. As a Honda owner/maintainer I appreciate the insight
That's interesting, I work on motorcycles and ngk is used on almost everything, and pretty much all modern bikes have aluminum heads. I have never once put anti seize on spark plugs, but another tech who came from an older car shop swore by using it on all spark plugs. I personally never found a need for it, the only spark plugs I've had trouble getting out are ones with damaged threads from improper instalation or over torqued by the customer.
Real lifesaver! Thank you!
I've been telling people for years! Nice to hear it for the first time from someone else.
Flashing back to many thread repairs in aluminum heads*
Thanks for that info!
Excellent educational content and video!!!✌️😎👍👍👍👍👍👍👍All The Best!!!
love this tip, thank you!!!
It's also more likely to loosen up with all that lubricant on it the last spark plug I saw that blew out of a cylinder head that had a ton of anti seize
Damn thanks. Put the beating on infinite loop please, I deserve it.
I'm glad my parts store never said a dam thing...nor the box. Is my subi broken now
No.. Just don't do it again. Lol
Thank you very much for this video, I was just about to replace spark plugs on my Subaru Legacy I gen from 1994. Replaced, WITHOUT anti-seize compound.
W SUBARUs
Great advice for any spark plug too! 👍
100% agree! While doing a tuneup on a friends car, he tried to hand me some anti-seize and I told him NGK spark plugs don’t need it. I told him to research it.
Great advice, I had no idea 😉
Anti seize on spark plugs is like putting antiseize on a ground cable 😂 Rookies!
This was really interesting, but I have just one question… is it OK to put anti-seize on an NGK spark plug?
I put anti-seize on all spark plugs and I've never broken one. Never really had an issue either. I also don't torque spark plugs with a torque wrench
Thank you very much just bought some for my 2010 Honda civic
How is ASe certified since the 90s and I used to tell mechanics this and they would always get real sick but now it's good to see it's popular
I've had zero issues with putting anti-seize on spark plugs for decades - works really well for long life spark plugs. I never use a torque wrench for spark plugs - always go by feel for safety.
Talk about passion!
Well you save me and a bunch of others a butt load of money thanks
So glad this vid was made!
I'm in Australia and my Gregory's manual which is much the same as Haynes manuals, says to put anti-seize on the spark plug threads and also to put RTV silicone on the Water Pump Gasket as well as the Threads of the water pump Bolts!
All completely wrong.
Actually some engines, have a water pump bolt that goes through the w.p housing and requires rtv on the thread to prevent leaking. Rare occasion but it is a thing
@@timwinslade7462Yeah some engines but we're talking about the Subaru boxer engines specifically.
Ford Triton has entered the chat:
Doesn't run NGK plugs. Is a garbage Ford. *Triton leaves chat*
@@MrSubaru1387 😂😂😂
Some service manuals say to put a touch of oil on the thread.
I pefer using red loctite. ( obviously i say this in jest)
Red loctite, imagine🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣
Loctite's great... 😅👍
Thanks! I seen that brand at autozone and got it. Just changed and used it on my parents car, hopefully it lasts a long while!
I just did mine yesterday without apply an anti-sease thanks!😬
Wish I had a seen this BEFORE I PUT ANTISEIZE on my NGK... 😮
Thank you kindly sir. I'm glad I was being cheap lastnight at autozone and did NOT purchase any antiseize...
but how will Auto Zone sell all their goo packs!?
I use to work at a Honda Dealership and couple of the technicians would give me crap because I would never use anti seize on plugs 🤣
That’s good information now I’ve got to go change some spark plugs
lmao i replaced the plugs in my truck with these ones and i didn’t put anti seize on them and i was worried they were gonna get stuck so this is good to know 😂
Thank you for the information I did not know that
You can't stop me!
Big inch nitrous big block guy… have always used it…. Never an issue… pull plugs after each hit…. 3 times a night maybe …. Never heard this
Thank you.
I can see why the strong emphasis on “do not” repeatedly happens.
It’s insane how many fools do this on every nut and bolt, not everything deserves anti seize or “never” seize. If the manufacturer did not put it on… then it doesn’t need it!
Doesn’t help that autozone GIVES the anti-seize for free when u purchase the plugs.
Class says, Yes Mr. Subaru
Totally agree with you years ago I used to be the anti-seize man I think even Denso states the same thing for their plugs
Yep.
Wow, my '90 Pontiac had aluminum heads and I always installed it's spark plugs w/o anti-seize on them (because it wasn't around / popular then). Then all I hear, anti-seize this anti-seize that, and thinking that I'm old fashioned and technically out of touch... Now, here I am trying to be "professional" and putting anti-seize on my '02 Subaru's spark plugs...
Now I just feel like a merry-go-round that everyone's enjoying playing with!
🤣👍
That’s a good bit of info
Good info
always put anti seize on the threads of an ngk sparkplug. got it.
soo...I just did this yesterday....what do i do...take them out and wipe it off?
1 year later I still feel like I'm being scolded. 😂
Good to know😳
Under torquing is also a relevant issue with regards to anti-seize. +/- 15%-25% from your torque value (dry) can cause huge problems with nuts walking off - primarily suspension components.
I think over-torquing is the big concern. The lack of friction can cause the plug to get so tight that it breaks or pulls the threads out of the head. Installation torque has to be reduced when the thread is lubricated.
Thank you 🙏
Huh, didn’t know they had some specific corrosion inhibitors.
Cause I’ve always used a tiny bit of copper anti seize on all my plugs. 🤷🏻♂️
It's a stupid debate that has been going on for a while. I don't put it on any plugs just because I don't want that crap all over everything.
That being said... I've put it on hundreds of spark plugs with 0.0% I'll effect, even with NGK.
Just because a manufacturer says to do it one way, doesn't mean it is guaranteed to be the best decision.
There's no debate. You don't put it on them. The spark plug manufacturer says no. End of "discussion".
ngksparkplugs.com/en/resources/5-things-you-should-know-about-spark-plugs
@@MrSubaru1387 I have never used anti seize and have never had a problem with them not earthing or with corrosion or a plug being stuck. don't put shit on them , don't over tighten them 🤷
Dont use the copper that is for exhaust stuff. Use the gray one. It makes zero ill effects but what it does do is keep the plug from seizing in the head.
I’ve been working on cars for 20 years and have never put anti seize on any spark plugs and never had any problems removing them
I've always used Red lock tight
Thanks!!!
Super relevant- autozone tried to sell me some when i bought my NGK 6510’s last week, i said no thanks, but enjoyed buddies reasoning~ NOPE!
Jesus this strap on lovin dude just loves the sound of his own voice.
But totally agree. Lol
Too late, the anti-seize is now on there forever 🤷🏻♂️
Someone grab this guy a snickers 😂
Thanks for the tip, on another topic, what battery do you recommend for 2007 SOHC 2.5L NA engine for Northeast resident.
Thanks
The graphite, copper and aluminum in antiseize are all good conductotrs. They won't affect conductivity between the plug and the head. And the liquid component is squeezed out at the metal to metal contact points just like dielectric grease is squeezed out when used in electrical terminals. The torque is affected.
This is good info! I recently pulled the plugs on an EJ251 (doing head gaskets). They had anti-seize on them and came out hard. One was VERY difficult to turn out - I thought for sure I had galled the threads. Had the machine shop check and fortunately threads just needed to be chased. Maybe anti-seize is a carry-over from when 100,000 mile spark plug routines first surfaced years ago?
On another note, what do you recommend for spark plugs? I was on the NGK website this morning and there's many choices. It''s only 4 plugs, so a few dollars more is ok with me if it's worth it for the long run. Car is a 2002 Forester, non-turbo EJ251. Thanks Mr Subaru!
Great tip!
I got an oil leak on there I need that anti seize and dielectric grease too late honestly they've been working just fine on my honda
I believe this applies to any other spark plug
Just one more reason why I don't like using NGKs...
Thank you for the reminder 👍
put new plugs on my 2020 STI. used copper antiseize like a scrub. Got the plugs hand tight, then turned about 2-3 inches worth with the rachet. I know not to crank down on spark plugs, so i only did a little bit of turning after it got snug...even tho it felt like i couldve kept going. but i didnt know about not using anti seize... how screwed would you say i am??
I thought anti-seize was a no-no for any car with an O2 sensor. Or was it with a Cat? They usually go together anyway...
Too late. And im not taking them back out now. Ngk also states that if you did use anti sieze not to take them backout until bext service i believe. Luckily i only use a very very small drop at the start of the threads.
Well i hope i didn't just mess up. Its been in amd running fine for the last 3 yrs.
I never use anti-seize on anything like that I've never done it but now I have a big reason not to ever do it and I did not know that
We went over this in school, and I followed this advice for a long time. Then I ran into a few original NGK plugs that were incredibly scary to remove, including in a subaru. I did some research, and I did come across some articles about the non-conductive nature of antiseize filler affecting the path to ground - BUT, people have been putting anti-seize on plugs for decades with no issues, and I have never seen this cause an issue on an NGK plug. Can anyone confirm that this has EVER caused an issue for this reason? I am always careful to apply just a dab starting a couple threads up to ensure it doesn't find its way to the electrode. As far as torque, assuming you are capable and have experience torquing things, have a feel for how the crush washer crushes, etc, is there really any legitimate reason NOT to put antiseize on these plugs? As far as I can tell, there is no interaction or anything, at least with the copper antiseize that I use (the stuff that comes with O2 sensors that I save). I've never had an issue with under or overtorquing when doing it by hand instead of with a torque wrench, and I've never seen it cause comebacks for misfires of any sort. I am not at all trolling here, because I really do want to know if there is any confirmation of a problem. As I said, I was on the other side of this argument previously. Now, every plug I install (unless it's on something crazy and exotic with super specific plug installation instructions) gets antiseize.
Just change them in time and you should never have an issue
Woops I put some on there but only a tad bit very thin coating on one part of it
Now I know. Oops. Did that to an older model of civic before. It is time to change it out this summer I guess and I’ll find out…
So what about on older iron block engines?
Fuck I put anti seize on my ngks on my wrx
Copper anti seize helps ground the the head :P
Damnnnnnn you know how many years I’ve done!!?
I just did my first ever change of spark plugs and ignition coils. I did use the anti sieze because again, my first ever job like this by myself..
they are NGK iridium IX plugs. did I fuck it all up? or is one time okay? I didnt apply much at all. any responses are greatly appreciated. vehicle is a 2004 accord ex with the k24
If I dont put it on and the plugs ruin my head, are you going to cover the damage?
I install them with no anti seize compound anyway
This probally includes the AC Delco platinum and iridium plugs which are made by NGK too
How about "don't use anti-sieze unless it is specifically called for" period. Nothing pisses a mechanic off more than getting slimed by the 3 tablespoons of silver snot that weekend warriors insist on putting on their lug studs.
Side note, that wet torque thing applies to everything. If it has a specific torque spec, it'll tell you if you need to put something on it.
You don't need to hang off a spark or torque one down either. Once you know the feels then you got that talent. On competition vehicle's yes I understand. Once you've done a few hundred civilian cars you should be able to fit spark plugs without cracking them in an engine and if you do then you'll never do that again 😂
I use anti sieze and never had a problem