Thanks for adding the info on the SRx_ADSB parameter. Since my ground station is connected via Telem 1 and a radio, setting SR1_ADSB=2 got me up and running.
Hello hope all is well ...I have a question..I been trying to get the ADSB working on my cube orange..I have updated the board with new firmware parameters I set all but can't find ADSB enable ..I typed in ADSB_enable and nothing shows
Hello! Thank you very much for this informational video. I was wondering if you have already done or will be doing a review on the Kore Carrier board for multi rotor use?
It’s on my shopping list tbh just not had the funds to go all in with it yet. I’d like to build a large hex with it, something like an S900 would be ideal.
I am working with a Orange Cube and have a x7 Taranis q bound to the receiver , When i connect to mission planner i can move the flight controller but when i get to radio calibration non of the areas in the pitch, roll etc. is green how can i make the transmitter be seen in the radio calibration . Thanks for your help
Hey there! You're videos are always helpful to me. Could you please recommend me a flight controller and PDB I'm planning to use 6 Hobbywing X8 motors with 40mm props for my 6axis filming drone and it's going to be hybrid.
What wifi adapter are you using in the testing part of the video? I'm a noob to autopilot hardware, using a lot of your videos to learn. Is this wifi, ethernet wifi? I hear you say UDP. So I'm assuming yes. Do you have a video on this?
Hello! I made the necessary settings and saved them in the controller. I restarted the controller, connected it to the PC with a USB cable ... but no air traffic appears on the Mission Planner map ... Is it possible that you do not receive radio signals inside a building near a window, or that you do not transfer data to Mission Planner via a USB cable? Thank you for your answer!
Hello, I have a question and if it sounds rather dumb, it's because it's an ongoing education, learning by videos such as this for my fpv builds... So my 1st arduplane build has MP 4.1, and every time I boot up MP, it now says a new update is available, but I just ignore and press on...so I have purchased the pixhawk orange cube standard set for my reptile dragon 🐉: understanding that the orange cube requires firmware 4.0 and up, can I load the same firmware on the orange cube as I have on my first build?? By the way, first build is with original pixhawk black cube standard set. The way I understand, I should make a copy of my parameter file, update, then reconfigure my first build all over again, then configure the orange cube... Now if that's wrong, we'll, I'm still learning...but I could use your help to clarify this you would sir? Thank you
Dear, Is it mandatory to to use the standard carrier base to fit the ADS-B antenna? can be used the mini carrier base or even the dronee carrier base? Thanks for your classes!!
Hi, i have uploaded a copter quad frimware as you said and uploading done successfully, what the main problem is i'm not abele to connect the flight controller in any bands. checked for several times but no use. just brought this orange cube on 18/11/2019. looking forward for to solve the problems, as my project dead line is so near. please help me on it. thank you
@@MadRC I mean it's not connecting on any values of bites like 57600, 111100.......etc., after that i have update the plane 4.0.7 frimware update was done successful but still i'm not abele to connect on any bit rate.
I suspect you have a driver issue, I would download the latest drivers again from the Ardu page and then install them. You may need to do the flush from Mission planner as well. There are some specific issue with windows 7 on this especially.
@@MadRC I'm using windows 10 and have downloaded new drivers as well but still its not connecting, can you share me a link of the driver which you have used or you can send me an email at gowtham@marutdrones.com and also please send me the firmware which you have used. this would be a great help. thank you
Thank You from Frisco, TX. Just bought the Cube Orange.
Thanks for adding the info on the SRx_ADSB parameter. Since my ground station is connected via Telem 1 and a radio, setting SR1_ADSB=2 got me up and running.
No issues, yea this one needed a bit more explaining .
Nice video, Poldark!
Thank you very much for the information!!!
Thank you for the video
Thanksss
Hello hope all is well ...I have a question..I been trying to get the ADSB working on my cube orange..I have updated the board with new firmware parameters I set all but can't find ADSB enable ..I typed in ADSB_enable and nothing shows
Hello! Thank you very much for this informational video. I was wondering if you have already done or will be doing a review on the Kore Carrier board for multi rotor use?
It’s on my shopping list tbh just not had the funds to go all in with it yet. I’d like to build a large hex with it, something like an S900 would be ideal.
Hi, there so is the orange cube not compatible with the Betaflight Configurator?
I am working with a Orange Cube and have a x7 Taranis q bound to the receiver , When i connect to mission planner i can move the flight controller but when i get to radio calibration non of the areas in the pitch, roll etc. is green how can i make the transmitter be seen in the radio calibration . Thanks for your help
Hey there! You're videos are always helpful to me. Could you please recommend me a flight controller and PDB I'm planning to use 6 Hobbywing X8 motors with 40mm props for my 6axis filming drone and it's going to be hybrid.
you can use pixhawk cube orange with more carrier board or go with higher versions of dji flight controller.
Is the Px4 compatible with Pixhawk Orange CUBE. I am not able to get a V-Tail plane configured properly.
how i can put out sd card_ thanks
What wifi adapter are you using in the testing part of the video? I'm a noob to autopilot hardware, using a lot of your videos to learn. Is this wifi, ethernet wifi? I hear you say UDP. So I'm assuming yes. Do you have a video on this?
Does hearlink is batter than... DJI...
Hlo sir how many magnetometer or compass is inside the pixhawk cube orange
three
Hello!
I made the necessary settings and saved them in the controller. I restarted the controller, connected it to the PC with a USB cable ... but no air traffic appears on the Mission Planner map ...
Is it possible that you do not receive radio signals inside a building near a window, or that you do not transfer data to Mission Planner via a USB cable?
Thank you for your answer!
Yes is very low signal is ADS-B, when indoors they would literally have to be over head and it still may not work in some buildings.
Hello, I have a question and if it sounds rather dumb, it's because it's an ongoing education, learning by videos such as this for my fpv builds...
So my 1st arduplane build has MP 4.1, and every time I boot up MP, it now says a new update is available, but I just ignore and press on...so I have purchased the pixhawk orange cube standard set for my reptile dragon 🐉: understanding that the orange cube requires firmware 4.0 and up, can I load the same firmware on the orange cube as I have on my first build?? By the way, first build is with original pixhawk black cube standard set.
The way I understand, I should make a copy of my parameter file, update, then reconfigure my first build all over again, then configure the orange cube...
Now if that's wrong, we'll, I'm still learning...but I could use your help to clarify this you would sir?
Thank you
Dear, Is it mandatory to to use the standard carrier base to fit the ADS-B antenna? can be used the mini carrier base or even the dronee carrier base? Thanks for your classes!!
The carrier has the ADSB receiver in not the FC so the Mini Carrier will not work,
Hi, i have uploaded a copter quad frimware as you said and uploading done successfully, what the main problem is i'm not abele to connect the flight controller in any bands. checked for several times but no use. just brought this orange cube on 18/11/2019. looking forward for to solve the problems, as my project dead line is so near. please help me on it.
thank you
Please explain what you mean can’t connect in any bands ?
@@MadRC I mean it's not connecting on any values of bites like 57600, 111100.......etc., after that i have update the plane 4.0.7 frimware update was done successful but still i'm not abele to connect on any bit rate.
I suspect you have a driver issue, I would download the latest drivers again from the Ardu page and then install them. You may need to do the flush from Mission planner as well. There are some specific issue with windows 7 on this especially.
@@MadRC I'm using windows 10 and have downloaded new drivers as well but still its not connecting, can you share me a link of the driver which you have used or you can send me an email at gowtham@marutdrones.com and also please send me the firmware which you have used. this would be a great help.
thank you
Where can someone buy it from ?
3DXR is a main dealer.
@@MadRC is there a website ?
@@MadRC thank you ,I found it ,cheers for your help mate !
nice one ian ,stop demoitising gary.
Haha Bruce wins that count more than anyone 😜
Here here
I see your Mission Planner defaults to the right part of the world.
Hello, I would like to know if the same is set up for pixhawk6c?