The two spacers go in the middle of the single cross pin that goes into the output gears, which keeps the gears meshed fully, and also helps add a little pressure on the orings as you mentioned. You got them in the right spot.
Holy shit bro thank you so much for this video me and my buddy were wondering where these two little washers go I got everything else put together but I'm like damn I wonder if somebody makes a video?? So thanks a lot 👍👍💯
I saw in another video the guy gave the large O-rings some very gentle stretches to flatten them with out. I don't think I could have seated them properly without that. Also I didn't tighten the screws down as hard as this guy did. And I used blue threadlock. Also I lubed the o-rings before assembly because I put the lower and gear section together, added oil and then tried to hold the whole thing by the ring gear and of course it dropped and fell apart. But i haven't noticed any leaks now that it's together
Thumbs up from the Hot Racing help desk! I'm always seeking good instructional vids for my customers. Keep up the good work, I'll be sending viewers.
You are a scholar, a gentleman, and a lifesaver. Thank you much for making this video man, cheers!
Glad it helped!
a tip : watch movies at Flixzone. I've been using it for watching a lot of movies during the lockdown.
@Chase Jefferson yup, have been using flixzone} for months myself =)
The two spacers go in the middle of the single cross pin that goes into the output gears, which keeps the gears meshed fully, and also helps add a little pressure on the orings as you mentioned.
You got them in the right spot.
thank goodness for your video, was about to throw this thing away until I saw where those two washers go
Sweet I finally ordered this part this morning it’s been on back order for weeks. Your video really good information.
Holy shit bro thank you so much for this video me and my buddy were wondering where these two little washers go I got everything else put together but I'm like damn I wonder if somebody makes a video?? So thanks a lot 👍👍💯
Thanks for the tip! I had no idea where those 2 shims could go🤪
I really appreciate your doing this video! I was lost until I found it.
So yours only came with 2 silver shims? Mines came with4.
Keep up the good work!
I have a 2wd vxl and I tried 50k dif oil, that doesn’t really work well, would you recommend I go to something like 100k or 500k?
Something sounds like it’s not dealing if it’s still leaking.
they got people on reddit putting 1m in there drag slashes damn near makes it a welded diff, but thats with the beveled magnum diff
Those little Rings Go on the Middle Pin
Thank you
How does 10k do I saw a video of them using 500k
trust me 300k barely does anything, going any lower just means that you might as well have an open diff
i know its a old video but A+ music selection haha, i swear every rc video is nothing but hard rock or edm lol
Do these diffs leakV
?
No they dont
And if it does just buy thicker fluid
I have 50k in mine and it leaks. I used Teflon tape on the four diff bolts too. Any suggestions?
I saw in another video the guy gave the large O-rings some very gentle stretches to flatten them with out. I don't think I could have seated them properly without that. Also I didn't tighten the screws down as hard as this guy did. And I used blue threadlock. Also I lubed the o-rings before assembly because I put the lower and gear section together, added oil and then tried to hold the whole thing by the ring gear and of course it dropped and fell apart. But i haven't noticed any leaks now that it's together
Some parts come bad
I need to put your hands down so people don't see what you're doing with it above the top of the video
Could hear you better with out the music in background
I heard him fine... the music wasn't even loud
@@mr1osia good for you
Alright 👍
Dude instead of buying hot garbage parts why don’t you buy a set of hex drivers instead of using those tiny Allen’s.