FAULT CODES C0045, C0050 ... 2007-2014 GMC AND CHEVY. WHEEL SPEED SENSOR REPLACEMENT.

WHAT IS GOING ON GUYS I RECENTLY KEPT GETTING FAULTS FOR THE TRACTION CONTROL SYSTEM IN THE YUKON, HERE IS WHAT I DID TO FIX THE ISSUE. HOPE THIS HELPS SOMEONE OUT. THANKS FOR WATCHING AND PLEASE SUBSCRIBE.
WHEEL SPEED SENSORS
amzn.to/2QwdBDj
YUKON HEADLAMPS
amzn.to/2QsIMzd
KEY WORDS:
INTERMITENT TRACTION CONTROL LIGHT
SERVICE THE TRACTION CONTROL LIGHT
ABS FAULT
2007 GMC YUKON DENALI CUSTOM
2007 YUKON ISSUES
..

[@josephpittman2030]

Hey man, I looked at your video. I changed out my rear ABS sensor on my 14 GMC yukon xl SLT. My ABS light and Stability and Traction Light been off since I changed the part. I also disconnected the battery too before I put the NEW sensor in. Thank you man. 😁😃👍😎

[@noelg5916]

Awesome

[@alanrussell2010]

Nice job J. U dah man bro. You take good care of Momma's ride

[@an_auto_addiction5742]

thanks as always man i do appreciate it.

[@shaunhouston2254]

My stability & traction light comes on only when I go through a car wash or when it rains, do you think it’s the high speed sensor? I also have the engine power light come on as well. It clears up once I turn my 2012 Yukon Denali off & sit for about 5-10 minutes. What are your thoughts?

[@coreylomeli1667]

I changed rear bearings now the abs an trac lights are on ?

[@dannyhawkins84]

Will it cause more problems than just out ABS light and traction so late I've got a problem with no communication reset the TCM an ECM, and it was going good until that sensor fault came back up and then start running like crap again

[@geegeego5188]

I just paid 370 for a sensor n wheel barring smh cus I had an ABS light on and traction control I'm so upset

[@KAREN91564]

Can you tell me where the Yaw Rate sensor on a 2007 GMC Yukon Denali is located?

[@L2fish]

Changed mine. Scanner still says no right rear wheel speed sensor signal.

[@MrChevyzz8]

Same as mine. Any luck fixing it?

[@L2fish]

@@MrChevyzz8 No. I checked the reluctor to make sure it was spinning. Trying to check the wiring back to the ABS module but I cant find a wiring diagram. I changed the ABS module but then I got a red brake light and the abs lights still on. Maybe the module has to be programmed. I may end up paying to have it fixed

[@MrChevyzz8]

@@L2fish any luck with a fix? I think mine may be a broken wire somewhere.

[@L2fish]

@@MrChevyzz8 No. I tried changing the ABS module but then I got a red brake light warning. I am thinking of buying a tool to replicate the signal then see if it shows on the scanner. I cant find a schematic to ring out the wiring back to the plug

[@josephpittman2030]

I have a Question, do you have problems with Slip Yoke ???

[@italianchevyman]

Did you have a hard time with the t30 screw

[@pablocastaneda3724]

Can tires make the stabilizer go off? I added some tires old tires 275 50 30 new tires 275 60 20?

[@an_auto_addiction5742]

It shouldn’t. . Would have to look at the wheel speed data . And see it it is out of spec for some reason. Most likely has a wheel speed sensor going out. Hope this helps

[@felixgalvan202]

Any tips for a stripped bolt? Same vehicle. The bolt head just stripped.

[@an_auto_addiction5742]

What is the bolt on.?

[@bloodybones63]

Left us in the dark on the upper connection part.

[@420flying6]

Replaced all 4 on my truck still got light damn it lol

[@fawnwhitmore1830]

Can't hear your