A new method of repairing a broken tooth of Gerari is a good method made of silver metal mandrel
HTML-код
- Опубликовано: 16 сен 2023
- A new method of repairing a broken tooth of Gerari is a good method made of silver metal mandrel
#new #method #repairing #broken #tooth #gear
#good #made #silver #metal Авто/Мото
Eyeball it until the casting fits. Truly revolutionary repair method, indeed.
I think I read about that in the latest academic journals.
I'm pleased to see this craftsman is wearing the trusted tried and tested standard issue safety sandals 👍
Yes, they are OASHA approved. (Occupational Safety Council, AKA gutshot bureaucrats.
Защитные сандали для похорон
The repair looks really good, but in that last shot I can tell just by looking at it the weld didn't get proper penetration. There shouldn't be a harsh line like that. I can't say if the entire weld didn't, but that edge sure didn't. The entire filler surface probably should have been cleaned via a little grinding prior to welding.
That edge might just be a bit of overhang from the lathe operation, made more obvious by the contrast. I get the same out of my cast iron gears..I can never get the weld dead flat with the rest of the gear without digging into the side of the rest of the gear so I wind up with that. Back lash in the carriage I suppose.
Should have done this with Tig. The guys smart, he just needs better tolls.. and yah.. some shoes wouldn't hurt either lol
Да ему туфли надо хорошие😅
Other than insufficient cleaning and poor welding, using an angle grinder to shape the welded tooth will never give him the correct angle on the drive or coast side of the tooth. If the angle is too steep, it will load the next tooth in line excessively. If the angle of the tooth is too shallow, it will load the previous tooth excessively. Either instance will result in more broken teeth.
Better cleaning, shielding adjacent teeth from splatter and using a high nickel rod would give the best possible life. Using a form ground carbide cutter in the lathe toolpost, he could have broached the tooth to be EXACTLY like all of the other teeth.
He needed a runout tab on the side so the start/stops would be outside the tooth edge and would machine off.
Я не устаю смотреть такие видосики. Когда совсем плохое настроение, включаю их и мне становится легче - как же много вокруг долбодятлов и самооценка, а с ней и настроение повышаются. Я считаю, что это терапевтические видосики, получше любого доктора психотерапевта!!!
мне тоже нравятся такого рода видео, я учусь в центре технического обучения и люблю сварку, этот человек хорошо работает, но его работу нужно немного довести до конца
И добавить нечего, нахер мозгоправы когда есть такие ролики)))
Особенно понравилось когда єто тело вставило шестерню в токарный с умным ебалом а потов тщательно все захуярил болгаркой ! Гений бл...!
And the less vodka consumption will be better
@@trexmidnite водка это святое, не трож!!
Awesome work!
Модуль и эвольвента соблюдены, я спокоен.
Believe it or not! This is exactly what I am going to do with a loose wheel stud! I had the idea some months ago, now I see it's actually used! Thank you so much! Welding the stud sides by the way to make it fatter. Thank you.
Сколько негативных мнений, а вот я как самодельщик со стажем не удивлюсь что это еще и работать будет. Помню угловой редуктор делал из сателитов моста, сварка и болгарка была только у меня тогда. 8 лет, 3000 оборотов и порядка 80 га скошенной травы.
He got the welded tooth to very close conformity. Very nice for hand work, excellent.❤
did similar on my lathe gears but i brased them works fine
Супер мастер - эвольвенту болгаркой забацать смог
Я то же в шоке😂😂
Если мастер узнает что он сбацал эвольвенту болгаркой, следующая шестерня будет оплачиваться золотом!))
и нафик не нужен эвольвентомер , давече настраивал прибор )
И режимы закалки о отпуска.
И маска сварщику не нужна, без нее загар лучше ложится )
Para un mecanismo sin grandes requerimientos puede servir como chapuza para salir del paso. En todo caso lo que se añade es otro material sin penetracion y el tallado con amoladora una barbaridad aunque sean dientes rectos.
3rd world countries do what is needed with what they have, it is commendable, and good to keep repairing. If only new machines could be repaired like the old ones can be.
you think in a 3rd world country, that can't afford much, wouldn't want to do a poor repair job that breaks apart maybe causing more damage to more gears!
If your mind was developed, you would know that this video is fake, made for pure entertainment for people with no idea of reality. Did you notice the difference between the initial photo and the material they "fixed".. if your head was from the first world, you wouldn't believe it!
Making a bench would be a start 😅
That's a cheap repair method.
The heat treat is ruined. This will never hold up for long. sometimes it really is best to get a new one.
That's very good.
EXCELENTE VIDEO¡¡... Y MUY FACIL DE ENTENDER¡¡...SALUDOS DESDE MEXICO¡¡
It all depends on the gear tolerances. If these are loose-fitting gears, this repair may be adequate. But if the gears are tightly fitting, eyeball grinding is not good enough. The gears are likely to wear and clank and grind, perhaps wearing in to better conformance, perhaps to worse. Only time will tell.
I didn't think about that, but you are correct, I saw a few episodes on manufacturing machinery, and some of the gears they were making had to be within a certain tolerance, guided with a computerized cutting machine and checked within a tenth of a millimeter. 😦😦
if you look at the gear you will see that there is a lot of wear on one side so there is no way that it could ever be described as a "close fit" gear train.
doesn't it need hardening? maybe induction method best?
It only has to last long enough for the replacement part to arrive.
I did the same thing on the ring gear on a locomotive. Lasted a while and eventually they had to pull the engine and replace the gear. Kept them going anyway.
I need this done on my spine.
та же проблема брат
😂
Good!
All is there it is to make the Gear Working I am worried about the Material of Electrode that it should be near to the Gear Material. Thanks for the Video.
Mistrzowska robota - oszczędność czasu i pieniędzy.
Pozdrawiam
There is nothing even remotely "New" about this method of repairing broken gear teeth.
My family were doing this in their workshop back in the 1920's ( that is over 100 years ago) on steam engine gears.
In those days about the only welding rods that were available were early Quasi-Arc rods and the AC power source was very crude.
After the war we were running nearly 100 engine driven Lincoln, Petbow and Hobart welding sets.
The only difference being that welding power source and welding rod technology has come on in leaps and bounds since then.
Ps back then there was no such thing as an "Angle grinder" but we had the some of the very first Flex grinders that came into the UK back in the 1960's.
So the gears had to be set up on the "shaper" to re-cut the tooth profile.
It wasn't suggested that this was a new method.
@@tevya017 Look at the title of the video where it clearly states "A new method of repairing a broken tooth of....". Does that help clarify the error in your comment?
a shaper would be a better way to do it, if you had one. if not, well.
There are pegged and welded teeth in the back gear of my Southbend 9C. Works, bit noisy.
A bit of preheat wouldn’t go a miss and it’s definitely a bodge
Been watching these tird world mechanical technique of repairing cars and related parts; good efforts but all against modern technologies. Amazing
Thanks
اللہ پاک محنتی لوگوں کو سلامت رکھے۔ زندگی ایک جدوجہد ہے لیکن کسی نہ کسی طرح خدا فراہم کرتا ہے۔
Thanks
BRAVO ..
To anybody who thinks this is bullshit: I'm a metall worker too and I think, this not bad what he is doing!
If the weld was case hardened it might last but I think it will destroy the other undamaged gears.
Complain complain.. it needs to be hardened and forged etc.. this will work cause it is flexible as long as the sharp load is placed elsewhere on the gear it work
@@trexmidnite What is your educational attainment sir?
The gear will hardly generate a homokinetic movement. If the requirements are low, it is a solution to the problem.
Good works
What about hardeness of repaired teeth? Original has at least 55-60, but new one is just looking nice but does not have propertly characteristics.
might still last quite a while depending on the application.
Can we get a floor vise like that from Harbor Freight?
I'm excellente mechanikal enginieus and high class specjalista from Pakistan.
My quastion is, what is that "hardeness" iin metal, which you are talking about?
It's good that you don't have a residual current circuit breaker that triggers the FI when the flex sparks fly into the power strip😅
Hello Morning
Wishing all of you good health and a peaceful, joyful and happy new year
Cool work thanks 👍
That is definitely a new method. If that is cast iron that tooth will fall off by the time get your rickshaw started.
Good joob 😍🥰
good job
Thank you for sharing👌👌👌👌👍
Muito bom 😊😸
Car Starter ring gears on the flywheel 100 years ago had teeth renewed like this.
Finest people !
Wow. Very good. But Safety gear???
I want to see the machine working after this repair.
😫🤦
I've seen hundreds of these videos. One in a dozen they show the truck driving away. They never show if it still worked an hour, a day, or a month later. I bet, usually broken again.
@@georgegonzalez2476 That's right!
you won't see, they do it for youtube, this "repair" fail in seconds
Мне интересно когда этот зуб снова отколится сколько он дел наделает 😢, а он больше чем уверен отлетит при хорошей нагрузки
Я у себя наваривал несколько зубов в кубовой мешалке. Поработал две смены. Разобрал. Зубы на половину стесались. Так, что это до жопы.
Мягкий без не калёный металл
Вот ия про тоже, кажись туфта полная ,а как же закалка и всё такое? И сколько это проработает?
@@user-pl4ny8oe6wда ни сколько. Метал не сварился адекватно друг с другом. Соединение чуть крепче, чем на поксипол
Отлететь не отлетит но вот подгонка на глаз это жесть. Что он есть что его нет сейчас этого зуба
Well done
Крутые ребята! Как к ним попасть на ремонт?
10:30 🤣🤣🤣 ну думаю, а где фрезер?? а вот и фрезер!! А сразу он угловой пилой не мог обойтись?? бор машинку возьми, лапоть! Нет, я уважаю рабочих людей и эти тонкости -- не по нашей вине, но повеселили меня, спасибо!
Bravó!!!
That lathe work was shocking, not even close to running true and the tool was not cutting properly, I am absolutely disgusted
Using a thin grinding wheel, he could have ground a deeper keying slot in the dead tooth ! & when welded in, it would be even far stronger, and that the force that broke the tooth in the first case, would encounter a much tougher tooth and be far less unlikely to break in that spot on a second time.
People commenting without any knowledge… These guys don’t just throw everything away to replace with new like we do in Merica, some places they actually have to fix things and I bet they know what they’re doing as opposed to all the keyboard specialists here. Obviously they do this for a living and if these didn’t work they would be out of business fairly quickly.
manusia tidak akan kekurangan pikiran jika selalu kreatif . orang Pakistan adalah ahlinya 🎉
Excelente trabalho, ótimo profissional
Mr sneakers must be the bossman..
Ils sont extrêmement bon et fort, mais le trucs que je préfère dans leurs vidéos, c’est leurs chaussures de sécurités…😂
Parabem e o desemho que mamda molde top very good
I know is a patch and is a nice work, But the lathe sparks shoe that the gear got a higher carbon content than the weld , is just a time to this to get to fail as welding damages cast metal
Fantastico!!!!
Working with what you've got is admirable but how about bluing the gear in to the mating one. This is highly likely to vibrate its self to bits.
Даже лучше оригинала!)
This gear is steel but many gears are cast iron which are far more difficult to weld, Depending on the hardness of the gear itself this might last a long time.
Not if you're a good welder and the cast iron is quality.
@@77Avadon77 It's still a gamble, all cast iron has some impurities in it but yes some are better than others.
Views last forever... that gear would last 5 mins with that repair
I "Love the safety shoes" (Vomit)
How to f up gears in under 60 seconds
Wow, using a table. That's a first.
Gee. The gears looked so BIG in the thumbnail.
Hardened steel has left the group 😂
What exactly is (new) in this method?
Precisión molecular
Igual um Rolex!
welded incorrectly see the glaring gap in the weld(s) piled it on without removing all of the slag every time he poked at it with the rod a drop at a time
good try, though
A gear cog is only as strong as it's weakest point.
I would use a file near the end.
Top
Until first running. You might as well use a glue) До первого запуска короче, с таким же успехом можно было на клей посадить.
Why no one has thought of building a workbench yet is beyond me.
Nice
Primero no es algo nuevo, lo hacen en muchas partes del mundo.
Segundo, este tipo de reparaciones son "pañitos de agua tibia". Sirven para salir de un apuro momentaneo. Eventualmente esos dientes deberan repararse nuevamente puesto que las propiedades de esos materiales no es la misma que solo soldar y esmerilar. De hecho con solo calentar el material ya existen cambios importantes en la estructura metálica.
Normalmente las ruedas dentadas son aceros de alta dureza, generando resistencia al desgaste. Al calentar la zona, posiblemente produzca una cambio de fase, y lo q antes era resistente ahora ya no lo es.
1:Dude makes the involute gear profile by hand with grinder...
2:He kills the hardened teeth with metal casting.
3: The repaired teeth and their surrounding are not hardened again.
Do you have twin disc 8501 series gearbox for sale? Both old and broken ones are fine!
Which vehicle is it used in?
И сколько это отходит?
Nie mówcie że po takiej naprawie to koło zębate będzie dobrze działało.
Интересно, сколько потребуется электродов чтобы сделать такую шестерню целиком сварочным аппаратом.
Just run the complementary gear wheel with a bunch of sand in between and they'll fit /s
刃先は高周波焼き入れがしてあるはず、刃もインボリュート曲線で設計してあるはず
これでは形だけの再生になってしまい、再度同じところが欠けると思います。
interesting
looks good, but that weld will not hold up unless that gear is just for timing, better off drilling then tapping a screw(s) into that area, and then weld it and grinding, or you get a proper HOT full penetration weld (but that cast material probably is full of junk inside it ) ...
that may be a steel gear . cast iron would not weld well at all and would crack.
Super Amano 👌🔥el arte ase el maestro
Hand cut gear tooth? I also believe this was for entratainment only.
That kind of welding leaves residual stresses in the material up to yield point. That makes the “repaired” tooth very weak indeed, i.e. it cannot transmit the original torque. 😒
I think their basic approach was admirable considering the tools. But they could have done much better, the welding was rushed. And the final grind to form looks ok but doubt that any of the stress in the gear is coupled to the welded part. It looked to me that by "just eye-balling" the final grind with a hand grinder they are not going to have a useful functioning force transferring surface in practice. This one needed the final grind on that gear to be with a dial indicator.
Если сломались зубья шестерни, значит она была неправильно спроектирована.
Нагрузку выдержит?
Old method it work's but not long lasting in some case because grinding ,welding both are not so proper but it is hand work not shaper or milling machines.
Good job good effort excellent.
That wheel should be preheated first. There is no good connection between the wheel and the weld...
It is always these guys wearing sandals and squatting on the ground. They don't understand how and why the things are made using a specific process. They just think that if it looks good, it will work good as well lmao.
If the gear is steel the welded tooth will probably last as long as the others. Maybe longer.
sure no
Just wrong ...
Well, if the tooth is too hard, it will bend off. The core must be a bit more flexible than the surface and there aren't neither temperiong nor hardening. It will simply crach again and a bit lower this time. It is simple physics.
con lo fácil que trabajar en un banco de trabajo ,hay que hacerlo en cuclillas en el suelo
No gap for oil 😮
Quá giỏi
Какой марки электроды?