I think it's always a bit of a gamble but as a principle, it is far more likely to get a straight hole by inserting a drill into a rotating workpiece than the other way around.
МОЛОДЕЦ. ТВОРЧЕСКИЙ ПОДХОД. СОЗДАВАТЬ ЧТО-ТО, ТВОРИТЬ, НАХОДИТЬ РЕШЕНИЯ, ВОПЛОЩАТЬ В ЖИЗНЬ СВОИ ЗАМЫСЛЫ- ЭТО ПРЕКРАСНО! МНЕ ОЧЕНЬ НРАВИТСЯ ВАШ ПОДХОД:- В ПРОСТЫХ, ДОМАШНИХ УСЛОВИЯХ, С МИНИМАЛЬНЫМ НАБОРОМ ИНСТРУМЕНТОВ, С ПОДРУЧНЫМИ СРЕДСТВАМИ ДЕЛАТЬ НЕВОЗМОЖНОЕ! ВЫ ВДОХНОВЛЯЕТЕ ЛЮДЕЙ НА ТВОРЧЕСКИЕ ПОДВИГИ. СПАСИБО!
Da da , savršena cev za ostati bez sake. A vidim da covek ne zna da je ovo metak za olucenu cev.......Kad bude opalio jedan metak iz nje, sledeci klip ce te gledati kako pravi deblju cev ,nogama....
Very nice video👍 Does it have a proper chamber? I’m specifically talking about the area in which the cartridge begins to neck down to a smaller diameter, I’m curious to know if your drillbit had the right angle
@@TheRhinestoneHurricane Печально. Если вы занимаетесь такими работами, то он вам просто необходим. Впрочем, этот станок и для других работ весьма востребован.
Что то здесь не так, соосность при сверлении в таких условиях ( без токарного) получится только при встречном сверлении ( и пруток и сверло вращается навстречу друг другу
Is that barrel come from printer? I disassembled a big office laser jet printer for Gold , it had a few high quality metal tubes perfect for make a barrels like this one ;)
Das iest ein spilerei,mit dem drebang kan man ni so geradeaus boren1.2cweite di linije from borer kan man nur mit eine reiber fergleichen ni mit ei schmirglpapir.
No offence, but I can't believe that you drilled a perfectly centred through hole using this method. I suspect there's something you're not telling us.
@@TheRhinestoneHurricane Sorry brother, but the visible run out on that bar stock in the opening seconds-that alone-would make it all but impossible to keep a drill bit perfectly centred.And I doubt that anyone could manually hold a drill chuck sufficiently steady as to maintain accuracy to that degree. If it was that easy, wtf would we need engineering lathes?
I would like to see a test by shooting 2 - 3 rounds. Then I will believe in this method! Хотелось бы увидеть тест по стрельбе 2 - 3 патрона. Тогда я поверю в этот метод!
wenn ich ihnen zuschaue wird mir schlecht versuchen Sie es wenigstens mit Bohr Öl😁😁Drehmaschinen Öl - - einen Lg. aus dem Allgäu - Volkert B und Uschi ❤👍👍👍👍👍und noch ein Tipp für die Munitions ´kammer Ventil einschleif `paste - Ps. - - Die Explosions -Kammer muss dreimal so stark im Material sein wie das Geschoss selber 👍
@@TheRhinestoneHurricane Спасибо за видос! А я таких придурков которые в такой агрессивной форме пишут комментарии сразу блокирую, удивляюсь твоему терпению)
The 5.7 mm round isn't parabellum but the chamber has parallel sides so won't the casing split in a rather dangerous manner when you use this chamber adapter?
@@TheRhinestoneHurricane The AK chamber tapers 1mm in diameter along the length of the casing until the neck is reached. Obviously a taper aids extraction of the casing. I get the point about firing a 5.7mm round down a 9mm barrel, it isn't going to be a good experience.😂 You'll have to show the results.
@TheRhinestoneHurricane I do know they have barrels with no holes. I got 1 cheap for a 380 I brought back to life. But you're like me. I like to try and make my own stuff.
What happen if the barrel be rifled all the way even at the chamber ? No trouble ? And what else ? Is can see - the factory made guns always have no rifling at the spot where the cartridge will b and folowing the lenght of this
You're talking about the leads, this section which gradually phases from nominal bore diameter to the inside lands. This is accomplished by milling down the surface between the introduction of the rifling and chamber mouth,
@@TheRhinestoneHurricane answer - what Happen if the barrel are fully rifled + which is also what happens to the homemade rifled barrels- they Often get fully rifled - no chamber without rifle
Não amigo. Pior é não fazer, dar desculpas que não tem ferramentas adequadas. A maior e melhor ferramenta ele já tem, que é a criatividade. Parabéns a ele.
![BCA Barrel for Glocks Manufacturing: [How it's Made]](http://i.ytimg.com/vi/2dhQFhbdQX0/mqdefault.jpg)
![BCA Barrel for Glocks Manufacturing: [How it's Made]](/img/tr.png)
Wether it works or not, you should be commend for your perseverance, patience and primitive tools
Thanks ☺️
9mm is centerfire, .22LR is rimfire. How do you overcome that problem?
5.7x28mm is a center fire ;)
Aos críticos aqui presente que se julgam, tão espertos e inteligente, desentorte a alça de um pinico, sem quebrar a louça que o protege
Excelente !como os velhos tempos do velho oeste ,quando não existia torno ,assim aproveitamos a tecnologia nos dada por ET,s.
👽😉🖖
It's miraculous how you managed to make a perfectly centered through hole
Thanks, it’s pretty easy once you drill the first hole 🥵
First hole, thin drill bit, even more miraculous.@@TheRhinestoneHurricane
I'm not sure it is as perfect as you say.
I think it's always a bit of a gamble but as a principle, it is far more likely to get a straight hole by inserting a drill into a rotating workpiece than the other way around.
well Jozef, that is indeed the right way to do it@@jozefbubez6116
If this person had a China made mini lathe, he could build double barrel shotguns
from scratch!
Can you imagine the look on the face of the archeologist that finds this in 1000 years
МОЛОДЕЦ. ТВОРЧЕСКИЙ ПОДХОД. СОЗДАВАТЬ ЧТО-ТО, ТВОРИТЬ, НАХОДИТЬ РЕШЕНИЯ, ВОПЛОЩАТЬ В ЖИЗНЬ СВОИ ЗАМЫСЛЫ-
ЭТО ПРЕКРАСНО!
МНЕ ОЧЕНЬ НРАВИТСЯ ВАШ ПОДХОД:-
В ПРОСТЫХ, ДОМАШНИХ УСЛОВИЯХ, С МИНИМАЛЬНЫМ НАБОРОМ ИНСТРУМЕНТОВ, С ПОДРУЧНЫМИ СРЕДСТВАМИ ДЕЛАТЬ НЕВОЗМОЖНОЕ!
ВЫ ВДОХНОВЛЯЕТЕ ЛЮДЕЙ НА ТВОРЧЕСКИЕ ПОДВИГИ.
СПАСИБО!
пожалуйста :)
Da da , savršena cev za ostati bez sake. A vidim da covek ne zna da je ovo metak za olucenu cev.......Kad bude opalio jedan metak iz nje, sledeci klip ce te gledati kako pravi deblju cev ,nogama....
Aprendí mucho con tu video gracias por compartir maestro de todos los tiempos, saludos desde chile
Very good sir. Getting a centre hole threw that round bar free hand must of been hard did you do it first time. Nic work just using a drill.👍
Thanks, I have a drill press now 🤗
Can't believe I just watched you drill a hole for a half hour... cool project though.
Yes but what a cool hole :P
worst job, not safety and accurate and good.
@@TheRhinestoneHurricaneشسسظظظظظظظظش
@@mattivirta you're just mad he has the balls to do this. 😘
😂😂😂😂
капец конечно условия и качество изделия, + можно было бы сделать его с горкой... если не иметь вообще ничего и такое сгодится, но я очень негодую.
not a lick of oil while drilling, I bet it's not tempered anymore, wow
Very nice video👍
Does it have a proper chamber? I’m specifically talking about the area in which the cartridge begins to neck down to a smaller diameter, I’m curious to know if your drillbit had the right angle
@@Mihail2204 Thanks, the 5.7 case has a dual radius neck so it’s not difficult to round out 🙂
Aan de zijkant van een slijpsteen slijpen???????
Can please tell me what steel do you use? Thanks
I used a roller from a photo copier 😛
Very good. Maybe Missing subtitles for tools zises on MM used and chamber for bullet should be thicker for pressure.
It’s designed to fit inside the barrel, can’t be very thick 😉
А что, разве на токарном станке не проще ли и точнее было бы это сделать?
I don’t have a lathe 😪
@@TheRhinestoneHurricane Печально. Если вы занимаетесь такими работами, то он вам просто необходим. Впрочем, этот станок и для других работ весьма востребован.
Что то здесь не так, соосность при сверлении в таких условиях ( без токарного) получится только при встречном сверлении ( и пруток и сверло вращается навстречу друг другу
palisz wiertła wiercąc na sucho, chłodziwo jest potrzebne !
I use a drill press know ;)
why didn't you use any cutting oil, and be surein the future ti use sharp bits, the last oe was obviously dull and probably weakened the steel!
I used grease on the first bit, the hardest one to drill through ;)
Sur du petit calibre 🤔 22 lr , maxi,au dessus suis pas sûre que ça tienne la charge 🤔 😮
แล้วมันจะระเบิดตั้งแต่ลูกแรกมั้ย ขอรีวิวการยิงด้วยครับ❤❤
a smooth bore? What about the rifling?
We don't need no stinkin rifling B)
Pas facile de percer droit sans un tour!
Great video. Use some cutting fluid. Gave you a like.
@@paulromsky9527 thanks ☺️
Is that barrel come from printer? I disassembled a big office laser jet printer for Gold , it had a few high quality metal tubes perfect for make a barrels like this one ;)
@@tomspeed2000 I have used those but this one had to be drilled out of a solid bar 😉
Das iest ein spilerei,mit dem drebang kan man ni so geradeaus boren1.2cweite di linije from borer kan man nur mit eine reiber fergleichen ni mit ei schmirglpapir.
No offence, but I can't believe that you drilled a perfectly centred through hole using this method. I suspect there's something you're not telling us.
I do it all the time, no big deal :)
@@TheRhinestoneHurricane Sorry brother, but the visible run out on that bar stock in the opening seconds-that alone-would make it all but impossible to keep a drill bit perfectly centred.And I doubt that anyone could manually hold a drill chuck sufficiently steady as to maintain accuracy to that degree. If it was that easy, wtf would we need engineering lathes?
@@ratheanach5545 You can be believe what you want, I just grind out the goods 😎
😂🤣
The chuck that you push forward with the bits in it, is that set up on a little block or something? Whatever your doing is working man.
do you ream the chamber first before you riffle the steel
@@ccos720 yes 🙂
@@TheRhinestoneHurricane why do a lot of people say rifle the barrel first even gun smiths say that?
@@ccos720 might have something to do with the land introduction 🤔
Ik zou is een scherpe boor nemen en af en toe een drupje olie zou op zijn plaats zijn denk ik 😂😂😂
Isn't the chamber insert heat treated after finish?
Nope, relies on chamber integrity ;)
Has considerado hacer de pastor?
Very cool budget lathe
Kühlung und angemessene Drehzahl wären besser. Laienarbeit!!
Laienarbeit! Das hast du sehr rücksichtsvoll gesagt! 😂
Passender wäre Pfu***
Of coarse its amature work... or he would use a lathe. That doesnt mean he did a bad job though
Interesting... any tests planned?
I tested it with a blank that I made :)
@@TheRhinestoneHurricane Great. Just be careful testing live... fingers are priceless but strings (to pull the trigger) are cheap... :)
Sua habilidade é fenomenal 😮❤
Thanks 😊
Le centrage plus tôt folklo
Non va bene troppo tempo e troppo lavoro. non si fanno col trapano quei lavori. 😢
It's ok, I have a drill press now 😀
I would like to see a test by shooting 2 - 3 rounds. Then I will believe in this method! Хотелось бы увидеть тест по стрельбе 2 - 3 патрона. Тогда я поверю в этот метод!
Ну плешивому диктатору ты же веришь или нет? Хотя он только переобещать обещаемое обещать гаразд.
Метод рабочий, но дрочево... и точность, так себе.
Нет точно закрепленного центра. Есть ручной подгон под патрон. здрасьте всем. У нас в России за это содют)
Een hol pijpje 😂😂😂😂die had je ook in de winkel kunnen kopen dan had je sneller geweest😂😂😂😂😂👍🏻👍🏻👍🏻
Sehr lustig, besonders das mit der Eisensäge 😂
Allein schon daran merkt man dass der keine Ahnung von Metallbearbeitung hat.
Was dann folgt ist noch schlimmer.
@@Bluesmann1
Ja und?
Mach das mal mit so einem Setup 😂
wenn ich ihnen zuschaue wird mir schlecht versuchen Sie es wenigstens mit Bohr Öl😁😁Drehmaschinen Öl - - einen Lg. aus dem Allgäu - Volkert B und Uschi ❤👍👍👍👍👍und noch ein Tipp für die Munitions ´kammer Ventil einschleif `paste - Ps. - - Die Explosions -Kammer muss dreimal so stark im Material sein wie das Geschoss selber 👍
Which Quality Drill Bits did you use
@@mikrotech3103 I used tungsten carbide bits and I inherited from my grandfather 😊
Устранить фатальное биение не пытался? Это издевательство над материалом и инструментом. Ад перфекциониста!
Thanks
@@TheRhinestoneHurricane Спасибо за видос! А я таких придурков которые в такой агрессивной форме пишут комментарии сразу блокирую, удивляюсь твоему терпению)
@@Tik.Tak.Просто твою херню никто не смотрит, там и блокировать некого😂😂😂😂
Я не рискну стрелять из такого. Стенки тонкие, неравномерные.
Сделано нехорошо.
It’s designed to go inside the barrel of a 9mm 😉
Maybe the man wants to show that even without lathes and various machines, something can be made with a lot of improvisation.
The 5.7 mm round isn't parabellum but the chamber has parallel sides so won't the casing split
in a rather dangerous manner when you use this chamber adapter?
I don't think so, the 5.7 case should be fully supported :)
@@TheRhinestoneHurricane The AK chamber tapers 1mm in diameter along the length of the casing until the neck is reached. Obviously a taper aids extraction of the casing. I get the point about firing a 5.7mm round down a 9mm barrel, it isn't going to be a good experience.😂 You'll have to show the results.
Mate you need a metal lathe.Asap.
He needs a drill press.
Кто поможет с видио изготовлением ствольной коробки на мосинку или просто самоделкины проделки на эту тему.
I don’t know 🤔
@@TheRhinestoneHurricane ok
Like McDonald's, im lovein it....
Nice budget idea,I wouldn't go over a 22 cal but I'm doin it.....
Thanks, 5.7 is technically a 22 ;)
Quoi..!! Tu veux dire que tu nous a tenu pendant 35 minutes pour nous montrer comment faire un trou avec une perceuse..!??
It’s a very special hole 🙂
what about some oil friend?? it will protect your drills!!
I don't use this method to make chamber inserts any more, I have a drill press now :D
goos good. you bought or diy?@@TheRhinestoneHurricane
@@mitropoulosilias bought it 😊
You fire that and that shoulder and neck on that case will disappear. Not Good!
Well come my friend I liket your have skill 👍
Thanks ☺️
Have you ever heard of oil?😂😂
Sometimes ;)
Even oil would no longer help with the technology. He lacks more important fundamentals.
3rd drill bit is completely dull 😢😢😢
Why not just buy a cheap 9mm barrel ?
It would have to be a blank, can’t any holes drilled in it 😉
@TheRhinestoneHurricane I do know they have barrels with no holes. I got 1 cheap for a 380 I brought back to life. But you're like me. I like to try and make my own stuff.
Making your own stuff is quite fulfilling. Your sense of pride in creation is a remarkable feeling.
Untraceable
Способ изготовить смертельное,для хозяина, оружие.
C'est pas faux,😉 22 lr,maxi ,au dessus 🤔 boum 😮
yea that will last about a milisecond when it blows up in his face not a wise thing to do
et pourquoi ducros il se décarcasse ? bonjour la précision.. (a chier sans doute🤔) ....
13:28 the dude she told you not to worry about
Demasiado tiempo perdido en ese proceso
I think that a burral for good gun .😊
It’s not a barrel, it’s designed to go into a barrel 😉
드릴고정이 깔끔하네요🎉
Криво и тонкие стенки в мягком металле. Если горохом плеваться, пойдёт.
Huh? Why do you keep saying this to me. "Zip gun, zip gun, zip gun, zip gun, zip gun, zip gun, zip gun."
@@joshualuna3515 I suspect most people click on this video thinking I’m making a gun, you’ll just have to wait for that video 😉
Vuoi che contiamo i giri di quel pezzo di ferro.?.?.?.?
I don’t count them 😕
Que el señor te conserve manos y cara intactas...
hmm very basic and effective,smart brain
Thanks, I’m also working on a pen gun 😈
Ja en wat is het nu geworden 😂😂😂😂
me too I just watching
Successfully wasted another 10 minutes of my life... but so did he
MT fino esse cano 🔥 🫣 ...💣...💣.....
Незнам какво е това може да бъде всичко друго но не и цев
It’s a chamber insert, it goes inside the barrel 😉
Кто так сверлит?(12 стульев.)😂Ильф и Петров предвидели такое.
Ерунда, но ты победил в том , что сумел полчаса нам пропудрить мозг,браво.
Mucho ingenio y perseverancia genial .
Muchas gracias! ☺️
Cutting oil
I do use a bit of grease on the bits 😉
What happen if the barrel be rifled all the way even at the chamber ? No trouble ? And what else ?
Is can see - the factory made guns always have no rifling at the spot where the cartridge will b and folowing the lenght of this
You're talking about the leads, this section which gradually phases from nominal bore diameter to the inside lands. This is accomplished by milling down the surface between the introduction of the rifling and chamber mouth,
@@TheRhinestoneHurricane answer - what Happen if the barrel are fully rifled + which is also what happens to the homemade rifled barrels- they Often get fully rifled - no chamber without rifle
@@Vo_d_kontra_o_norMAL that would not work, the shell casing would get stuck 😦
@@TheRhinestoneHurricane the cartridge would get externaly rifled by expansion ? And the cartridge would get out by rotating it out like a screw !?!
@@Vo_d_kontra_o_norMAL that would be quite the extractor 😯
İstanbul'dan selamlar müthiş bir iş çıkardın
Thanks, you should check out my playlist 🙂
Some people shouldn’t be alowed to touch tools 😢…
That drilling is the worst ever 😭…
Yes you are right! don't understand the positive comments. Apparently most people don't understand what they're seeing.
این مال قبل از اختراع دستگاه تراشه 😢 ! آقا مته سوخت ! آب بریز !
Very cool!
Thanks ☺️
@@TheRhinestoneHurricane Can't wait to see some test firing on a range
@@doejohn8674 I already tested it 😯
@@TheRhinestoneHurricane I saw the other video with the blank cartridge, but did you try it with live ammo?
@@doejohn8674 I don’t have any live ammo, probably too spicy for the derringer 😬
у него руки золотые, их целовать надо
😂nice sarcasm.
🦵 ..... CANECA SECA ...😅....✌️...🇵🇹..
🦵 ...... canela seca.....✌️.....🇵🇹...
sera preso
Какой-то ребенок играется с папиным игрушками ,иди мультик смотри
The .57 is unstable in a good barrel
Its a crappy round
Good thing its a 5.7 instead of a dutch flintlock caliber then!
worst drilling what i ewer has seen, better not do anything before you have good tools first. build good lathe or buy,
Não amigo. Pior é não fazer, dar desculpas que não tem ferramentas adequadas.
A maior e melhor ferramenta ele já tem, que é a criatividade.
Parabéns a ele.
M
Sem interesse algum !...
Works for me 😊
2 word, "CUTTING OIL"
Video could’ve/should’ve been edited down to about 3 minutes!!!
The whole reason this video took off is because it’s over half an hour 😂
Nain teh.kultura.
Что за порнография???😮
Несоосность очень большая.
Пакистан!
America 😎
แผ่นตัดไทเทเนียม
Ананизм