Very beautiful. But it is worth trying by pulling... pulling is better than knocking, but it is also nice. We are waiting to try the accuracy on target papers.
@@Pauly5150 Yes, it would be good to see the accuracy of the assembly at a distance of 20, 30 or 50 meters. I hope for a wonderful group for assembly. 😍😍
Для дорнования нужно использовать спец смазки в виде покрытия внутренней поверхности, медью, свинцом или серой, использовать масла это риск задиров или заклинить дорн.
я сделал дорн из сверла, электролитическим травлением. сверло по металлу дешевое, закалка не нарушается, и диаметр можно подобрать с точностью до 0,1 мм. отличный вариант для тех, у кого из инструментов только молоток)
Да я на дорне канавки тоже травил только медным купоросом с солью, а потом и вовсе начал делать полностью на токарном канавки под нужный твист с помощью прямозубой накаткой, так получаются очень точные дорны.
Hi my name is Richard let me see if I get this straight You took a 5.6 mm tap and turned it into a rifling tap.???? Okay the the rifling looked good but how do you temper the tap back to tool harden????? That's actually really nice though.😊 Really the first rifling tap I've ever seen done really well thanks for sharing
It's an interesting video. Did you heat-treat the reamer off-camera? Just curious how hard the bit was after heating it for reshaping. Lands and grooves are usually wider than what this would make, but for a do it yourself technique, it's cool to see. I hope you chamber the barrel and do some accuracy testing. It would be cool to see the projectile with a high-speed camera. Thanks for posting!
Put a rest close to the wheel BEFORE you loose your fingers. What you are doing is very dangerous. (I saw a man loose half his hand when I was a young engineer 50 years ago)
@@pcpairgunschannel It stops the work piece being dragged under the grinding wheel along with your fingers. You will also have better control of the work piece. Keep safe.
@@locodriver601 for some reason my bench grinder came with no rest at all. would it be any less dangerous if i completely removed the guard around the wheel so that nothing could be pulled under the wheel?
@@pcpairgunschannel Not a good idea. You should keep the guard and make yourself an adjustable rest. It should be quite easy to do. A bit of time and effort is better than injury to your fingers.
Nice work, really loving your videos. That's the best DIY button rifling button I've seen being made and using the 6 flute reamer was the best starting point I've seen too. The big question with all these DIY rifling videos is, can the barrel take standard pellets or must you make your own to the exact dimensions of your barrel? I say that because even expensive barrels are choosy at the best of times, you'll get tight groupings with one brand and flyers with another.
From my experience in general most diabolo pellets work well. Since the grooves are a bit thinner using this method, it is best to keep it under 30 ftlbs to keep good accuracy.
@@pcpairgunschannel Thanks for interaction. I've watched possibly all the DIY PCP videos on youtube and you stick out a mile as the channel to watch. Again, nice work and thanks.
Super! Tell me please, what is the diameter of the shank? If the reamer is 5.6 mm, then what is the diameter of the tail section, since it fits so easily into the workpiece with a diameter of 5.5 mm?
Another way to polish a crown is to put a brass round head screw into your drill chuck in the steady rest and put some polishing compound on it then run it against the crown.
If you use this reamer method then use hss. Tungsten carbide and cobalt are harder, but they are more brittle. Due to that you would risk the button breaking if you used carbide
You are receiving compensation from youtube to teach peoplesomething worthwhile. Yet you continue to use a benchgrinder without a toolrest. Have you ever seen a picture of a human finger that was pulled down into the ever decreasing space between a spinning abrasive wheel and the mounting bracket that was designed to hold the toolrest. I worked as a toolmaker all of my working life, and have grabbed a shop towel to wrap around the finger of one fellow worker. A decent portion of the first joint was chewed away. I have ground nicks in my hands annd fingers over the years with the guards in place. Abrasive wheels are filthy objects that transfer that dirt to your open flesh as it is burned. Some of these do get infected. Keep a bottle of hydrogen-peroxide in your tool box, and put the damned guards back in place.
do you mean that I should simply add a rest, nothing complicated right? I got no rest when I bought mine... I have to make one by myself probably. possibly a production issue
Yes Sir it is dangerous to not use tool rest, little table, shelf etc. ur really lucky enough to have people to kinda give little hell so it doesn't cause a lot of hell in the future. Because it will eventually happen. Might not be real bad and on other hand. One could loose a hand. Maybe a life. They are very dangerous . Ok take care I love the channel id hate see a tool get a piece of you. Stay safe from ur ole hillbilly buddy
С добрым утром! Лучше не вопросы задавать, а ук рф 222 и 223 читать, затем фз-150 "об оружии", и знать, что пока заготовка ствола не имеет патронника, пригодного для осуществления выстрела - заготовка не является основной частью оружия и не подлежит никакому учёту. Название канала - про PCP винтовки, у которых нарезы есть, а патронника - нет. Ещё раз с добрым утром, просыпайтесь быстрее.
It's pretty, but not going to be much use. The lands are 95% of the rifling and will create a huge amount of drag. They should be about 33% of the rifling, with the grooves 66%. Also, what is the twist rate
@@hojatk7578 67/62? I am not sure what you mean by that sorry. But generally the button should be 0.1-0.2mm larger than the inner diameter of the barrel. Generally 0.15mm larger does the best job with a system like this, bcz the grooves need to be a little bit deeper.
Какой твист нарезов получился? Судя по видео, короткий, 10-12" Если для рср то это плохо, кое как может быть кучно будет лететь волан типа jsb. Про слаг даже не мечтай. Такова реальность.
Very good, the better homemade grooves i see on RUclips!
We are waiting for accuracy testing
精度应该不行
Very beautiful. But it is worth trying by pulling... pulling is better than knocking, but it is also nice. We are waiting to try the accuracy on target papers.
I might make a press to push buttons one day. I am still gonna experiment
@@pcpairgunschannel Good luck, brother, you are amazing
Great work. It will be interesting to see how it groups once it's finished.
@@Pauly5150 Yes, it would be good to see the accuracy of the assembly at a distance of 20, 30 or 50 meters. I hope for a wonderful group for assembly. 😍😍
Using a hydraulic jack will give you more control to push the reamer through the barrel
I will make a set up one day.
Tanks sir for your blog tankz
Not too shabby!
I am curious to see the accuracy
Some people in the comments really need to show us how it is done.
{So we can laugh}
@@LowkeyAirgunner this will be for my semi auto. Its gonna take a while to make it, I will order some more materials
Молодец,отличная работа
Для дорнования нужно использовать спец смазки в виде покрытия внутренней поверхности, медью, свинцом или серой, использовать масла это риск задиров или заклинить дорн.
Ото с дуру можно все сломать .кто профи!!!🎉
ok
veri۔goo❤❤❤درودبرهنرمندیتان .واقعا عالی بود❤❤❤
я сделал дорн из сверла, электролитическим травлением. сверло по металлу дешевое, закалка не нарушается, и диаметр можно подобрать с точностью до 0,1 мм. отличный вариант для тех, у кого из инструментов только молоток)
Да я на дорне канавки тоже травил только медным купоросом с солью, а потом и вовсе начал делать полностью на токарном канавки под нужный твист с помощью прямозубой накаткой, так получаются очень точные дорны.
@@sanchezicа зачем это всё нужно, если готовых бланком везде навалом и стоят они недорого?
you hammer very quickly i am impressed
Перевести. На. Русский
Beautifull work❤
Very useful knowledge 👍👍
Thank you sir! Your videos are amazing.
super video like always
Hi my name is Richard let me see if I get this straight You took a 5.6 mm tap and turned it into a rifling tap.????
Okay the the rifling looked good but how do you temper the tap back to tool harden????? That's actually really nice though.😊 Really the first rifling tap I've ever seen done really well thanks for sharing
You can heat treat it again
Только раб не имеет права сделать себе оружие ✊
не будем, такими 😊
У нас в России сразу под статью попадёшь за изготовление ствола или за хранение. Можно и на нары загреметь
@@murataflytunov223эта трубка ещё не ствол
Can you show us the actual testing to see how accurate it is?
@@mrkalikutista8729 I will once I finish my semi auto
I might suggest fire lapping but it’d probably rupture
Barrel groove very nice, however manual tool , i wait for tes accuracy ..mr ..👍👍
Turned out pretty good actually…
What rate of turn did it result in?? Looks about right…
The twist rate is too high, its 1:10, i will still experiment more rifling techniques and come to a conclusion.
It's an interesting video. Did you heat-treat the reamer off-camera? Just curious how hard the bit was after heating it for reshaping. Lands and grooves are usually wider than what this would make, but for a do it yourself technique, it's cool to see. I hope you chamber the barrel and do some accuracy testing. It would be cool to see the projectile with a high-speed camera. Thanks for posting!
I didn't heat treat it again, it's for an air gun so the lands to grooves ratio is not that strict
Put a rest close to the wheel BEFORE you loose your fingers. What you are doing is very dangerous. (I saw a man loose half his hand when I was a young engineer 50 years ago)
@@locodriver601 in that case I think I will but how will a rest prevent an accident
@@pcpairgunschannel It stops the work piece being dragged under the grinding wheel along with your fingers. You will also have better control of the work piece. Keep safe.
@@locodriver601 for some reason my bench grinder came with no rest at all. would it be any less dangerous if i completely removed the guard around the wheel so that nothing could be pulled under the wheel?
@@pcpairgunschannel Not a good idea. You should keep the guard and make yourself an adjustable rest. It should be quite easy to do. A bit of time and effort
is better than injury to your fingers.
@@pcpairgunschannelno, that removes the protection in case of the stone shattering/coming loose.
Nice work, really loving your videos.
That's the best DIY button rifling button I've seen being made and using the 6 flute reamer was the best starting point I've seen too. The big question with all these DIY rifling videos is, can the barrel take standard pellets or must you make your own to the exact dimensions of your barrel? I say that because even expensive barrels are choosy at the best of times, you'll get tight groupings with one brand and flyers with another.
From my experience in general most diabolo pellets work well. Since the grooves are a bit thinner using this method, it is best to keep it under 30 ftlbs to keep good accuracy.
@@pcpairgunschannel Good to know. Have you tried slugs?
@@richards6269 not yet.
@@pcpairgunschannel Thanks for interaction. I've watched possibly all the DIY PCP videos on youtube and you stick out a mile as the channel to watch. Again, nice work and thanks.
@@richards6269 I really appreciate your feedback!
Did you quench the tool after heating and grinding?
Nope
Hola hay que volver a templar el escariador despues de haberlo puesto al rojo vivo y torcido con el alicates?, gracias
Yo no hice eso. Funciona bien si el cañón no es demasiado duro.
@pcpairgunschannel osea no es necesario volver a templar el escariador,quisiera ver algunas pruebas de tiro ,visite ti canal pero no encontré ninguna
well done and very neat and impressive
It would be interesting for you to pass a miniature camera inside the barrel to see how the soul finish turned out
@@Gabriel-rn1si lets see if one day its affordable.
Thanks for making and sharing these videos with us.
Nothing worth in this !
Como se chama essa peça, qual o nome?
(5.6mm reamer)
Good video
And parts needed in description
5*****
What Type Of Gas
Are You Using ??
And What Torch Is That ??
Amén.
@@-mejor-que-nostradamus-6152 its just a propane torch
Awesome job bro 😎😎🤘🤘
Quebbuen trabajo amigo me puedes decir que numero de broca usastes para perforar el metal 2 de diciembre 2024
Did you quench the cutter end to harden it after you heated it up to twist?
no I didnt quench it, would have been good to do.
Nice, but will you put a cartridge in it, ignite it and watch if the barrel withstands 60000 psi?
The barrel needs to be hardened. This is just for a PCP rifle though, so no need.
Buen trabajo compañero
What twist rate are we talking, and how did you check it?
@@zenger74 too high, 1:12
Have to eyeball it
How did you bore the barrel?
its a steel pipe. i didnt have to do that myself
How did you get it to spirol ???
by making a twist to the reamer, just like a screw it forces itself to spin, but the principle is reversed
سلام لطفا تست دقت هم بزارید تا ببینم نتیجه کار چی میشه، 🙏👍
Super! Tell me please, what is the diameter of the shank? If the reamer is 5.6 mm, then what is the diameter of the tail section, since it fits so easily into the workpiece with a diameter of 5.5 mm?
I Sanded it a bit, to around 5.45mm
@@pcpairgunschannel I understand, thank you !
Thanks
Great channel.
يجب ان يكون الحلزون نافر وليس غائر
Well done!😂
Ótimo trabalho.
Please air gun barrel VDO please ❤
sadly, this is not how rifling works... but i like the video. very interesting way to use reamers for cutting lubricant lines into bushings. good job👍
This definitely isn't an ideal rifling technique for firearms, true. But for air guns this can give decent or even fairly good accuracy.
Hammer Geile Arbeit mache auch Handarbeit macht Geile Luftpistole
Ottima LAVORAZIONE 👍👍👍👍👍👍 calibro 22 ??? Aria compressa ??? O altro ???? aspettiamo continuo 👍
Sì, è per un fucile ad aria compressa calibro 22
Cuantas veces hay que pasarlo
Amazing work
Another way to polish a crown is to put a brass round head screw into your drill chuck in the steady rest and put some polishing compound on it then run it against the crown.
Se fizer isso num cano de uma 36, funciona bem com balas e cartuchos??
Talvez, mas vou usar isso para uma arma de ar comprimido. Para armas de fogo, um botão de raia comercial é a aposta
Obrigado@@pcpairgunschannel
I presume you skipped over the hardening (heating, quenching, annealing) of the rifling button.
Nice bro ur great
Ну, а кучи какие получились? Лист А3 или А1 на сто метров?!
Nice video
In one revolution how many inches?
1:10
Nice job😊 can you tell me where i can buy good quality Teflon for making valves please
I dont know a place apart from AliExpress
@@pcpairgunschannelsend me the link please
@@pcpairgunschannel please send me the link
@@mordimustafa1275 s.click.aliexpress.com/e/_DdPb4XF
you want to use it for the firing valve right?
@@pcpairgunschannel yes I want to use it for the valve and the refilling port too
Now to see what it likes.
Толку от этих канавок, только газы будут уходить. Нужны наоборот выступы, которые вгрызаются в пулю, тем самым её закручивают.
Nice wokk
実際のライフリングの製作は油のなかで油圧でライフリングのカッターを引き抜いてカットしますよ！
Cool
Perfect
Could you make the zip gun from the movie Munich?
@@brantonzhang i cant make actual firearms legally, only air guns
@ I meant to say prop air gun
@@brantonzhang Maybe I could make something like that one day, but its not in my plans
Bro can i try it carbon steel 6.5 mm tube is it worthy for me, which button good i for fine rifling hss,tungsten carbide,or cobalt please tell me
If you use this reamer method then use hss. Tungsten carbide and cobalt are harder, but they are more brittle. Due to that you would risk the button breaking if you used carbide
@@pcpairgunschannel thanks a lot for your value able suggestion, i will try
Using a spiral flute reamer rather than a straight flute reamer would make creating the rifling button much easier.
@@gerritmeester3390 spiral flute reamers have a too high twist rate
Como se llama ésa broca
Reamer
You are receiving compensation from youtube to teach peoplesomething worthwhile. Yet you continue to use a benchgrinder without a toolrest. Have you ever seen a picture of a human finger that was pulled down into the ever decreasing space between a spinning abrasive wheel and the mounting bracket that was designed to hold the toolrest. I worked as a toolmaker all of my working life, and have grabbed a shop towel to wrap around the finger of one fellow worker. A decent portion of the first joint was chewed away. I have ground nicks in my hands annd fingers over the years with the guards in place. Abrasive wheels are filthy objects that transfer that dirt to your open flesh as it is burned. Some of these do get infected. Keep a bottle of hydrogen-peroxide in your tool box, and put the damned guards back in place.
It never had guards in place. Since two people have said for this now then I will look how i can install them on.
do you mean that I should simply add a rest, nothing complicated right? I got no rest when I bought mine... I have to make one by myself probably. possibly a production issue
Yes Sir it is dangerous to not use tool rest, little table, shelf etc. ur really lucky enough to have people to kinda give little hell so it doesn't cause a lot of hell in the future. Because it will eventually happen. Might not be real bad and on other hand. One could loose a hand. Maybe a life. They are very dangerous . Ok take care I love the channel id hate see a tool get a piece of you. Stay safe from ur ole hillbilly buddy
Live dangerously lol
Great video !
Dao kéo rãnh khương tuyến có phải bạn làm từ mũi doa không?
Здоровская подзорная труба получилась.
Amigo . Que tipo de material es el escariador . ?
HSS high speed steel
@@pcpairgunschannelsera el mismo hierro de las llaves hexagonales ?
@@pcpairgunschannely el cañon que material es? Esque quiero pasar un cañon de 4.5 a 5.5 de acero .
@@posadaszproduction 42crmo
s.click.aliexpress.com/e/_DloTJpl
@@pcpairgunschannel And what do you recommend? I want to upgrade a barrel, from 4.5 to 5.5.
Yes Sir nice
استاد از چه نوع لوله ای استفاده کردید؟
16mm od 5.5mm ID 42crmo pipe
@@pcpairgunschannelازکجا میشه تهیه کرد؟
@@علیهادیان-ح3ض s.click.aliexpress.com/e/_DdOotUh
Yes
Nice
I dislike the disgusting adverts attached to this good bit of engineering.
Nice work ,did you use 5.5 or 5.45mm pipe? link doesn't work
sorry, link might have expired
s.click.aliexpress.com/e/_DdOotUh
I used 5.48mm pipe
Is this 22 barrel brother
yes, for an air gun
@pcpairgunschannel I mean 22 rifle
@@baklasbaklas It isn't intended for that, its for a pcp air gun. But you can use the same rifling technique for a 22 rifle
22lr?
.22 PCP
Size of the reamer?
5.6mm
Сколько лет дают за такое рукоделье?
С добрым утром! Лучше не вопросы задавать, а ук рф 222 и 223 читать, затем фз-150 "об оружии", и знать, что пока заготовка ствола не имеет патронника, пригодного для осуществления выстрела - заготовка не является основной частью оружия и не подлежит никакому учёту.
Название канала - про PCP винтовки, у которых нарезы есть, а патронника - нет.
Ещё раз с добрым утром, просыпайтесь быстрее.
It's pretty, but not going to be much use. The lands are 95% of the rifling and will create a huge amount of drag. They should be about 33% of the rifling, with the grooves 66%. Also, what is the twist rate
it is 1:10
this is for air guns only, it works quite well on air guns.
@@pcpairgunschannel I preferred choose twist rate 1:16 for airgun
@@jesensunjaya3882 yep thats the best. I would have done that but it isnt easy to manipulate the twist rate
how much?
How can I communicate with you??
send me your whatsapp number in email if you need to
@@pcpairgunschannel check your email
Write your email
Put on gun barrel and test it
I'm amazed when you put the heat on that thing it didn't get soft as pot metal
Твист на глаз сделал? только для воздушного оружия подойдёт.для точного оружия такое не годится
да, это для пневматического оружия
❤❤
Have you shot anything through it yet???
No, I will make a slightly different rifling using the same technique
@pcpairgunschannel oh I do want to see this.... Thank you for responding
Megustaria.arquirir.uno.donde.puedo.conplarl
not for sale, sorry
👍
Berapa twist rate nya tuan?
1:10
terlalu tinggi jadi saya akan menggunakan lebih banyak teknik segera
@@pcpairgunschannel tidak cocok untuk pcp tapi cocok untuk senjata api.
Kerja bagus, lanjutkan
👍👍
عمل جيد
لكن لا يمكنني المجازفة ، أخاف أن يعلق
😀diyer‘s god
Hai ferend said foor 7/62
its 5.5mm
What is the size of the nail for the pipe size of67/62for the house?
@@hojatk7578 67/62? I am not sure what you mean by that sorry. But generally the button should be 0.1-0.2mm larger than the inner diameter of the barrel. Generally 0.15mm larger does the best job with a system like this, bcz the grooves need to be a little bit deeper.
Какой твист нарезов получился? Судя по видео, короткий, 10-12" Если для рср то это плохо, кое как может быть кучно будет лететь волан типа jsb. Про слаг даже не мечтай. Такова реальность.
1:10
top,..