Installing Threaded Pems Inserts, No Fancy Equipment Needed.
HTML-код
- Опубликовано: 25 сен 2024
- With a little ingenuity is possible to install threaded press fit inserts (pems) into aluminum and steel with only an arbor press and some leverage.
Follow the 42 Pursuit journey: / 42.pursuit
LINKS TO EVERYTHING BELOW
Thanks for watching!
------------------------------------------
Below is a list of tools/supplies from the video and a couple additional tools that I really like, as well as video/audio gear I use to make these videos. Some of these links are generated by Amazon and provide me with a small percentage/kickback at no cost to you should you use them to purchase any of the items I use. Thanks for supporting me and this channel!
(this project is NOT sponsored)
Press-Fit Threaded Standoffs, 8-32 x 3/8"
www.mcmaster.c...
Datasheet for threaded standoff insertion force:
catalog.pemnet...
Press-Fit Threaded Pins catalog.pemnet...
Datasheet for threaded stud insertion force:
www.pemnet.com...
Other press fit fasteners: catalog.pemnet...
🛠️ TOOLS (affiliate):
1 Ton Arbor Press: amzn.to/3ARkukY
www.harborfrei...
2 Ton Arbor Press: amzn.to/3obvu92
🎥 FILMMAKING GEAR (affiliate):
Lumix GH5 Camera with 12-60mm lens: amzn.to/2ACvlVE
128GB SD Card UHS-I: amzn.to/3dBJfG7
Rode Wireless GO: amzn.to/2MBvTxr
Rode VideoMicPro: amzn.to/2MztvY0
3.5mm TRS stereo breakout cable: amzn.to/30biPHa
Cold Shoe Extension Bar: amzn.to/3dBhixZ
Blue Spark Desk Microphone: amzn.to/376o2lg
Desktop microphone stand: amzn.to/30mpjmX
🎼 The music I use in all my videos comes from Epidemic Sounds: www.epidemicso...
------------------------------------------
Are you a Patreon member? / 42pursuit
---Follow 42 Pursuit!---
INSTAGRM: / 42.pursuit
TWITTER: / 42pursuit
FACEBOOK: / 42pursuit
WEBSITE: www.42pursuit.com
Great video. Very helpful and informative. Thank you for sharing.
I've been looking into what I would need to build a custom computer case, and this is the exact video I needed to see. Thanks!
Sweet! That's a great idea using those for a custom computer case!
Very informative and short. Thanks.
I saw you on Will's channel and came for a look-see, I subbed.
Cheers from Tokyo!
Stu
Thanks for the sub!
A hydraulic crimping tool also works.
Hmm, how much do those tools cost?
@@42Pursuit I got a handheld hydraulic crimp tool from harbor freight for about $80 (USD). The hydraulic crimper is intended to be used to crimp fittings onto large gauge electrical wire, but since it produces up to 8 tons of force it can be used to install pemserts in certain materials.
What about the back material pertruding, is there a way to get countersunk bolts and nuts in a 6mm package so that the inside and the outside sit compeletly flush!
I have found some 110° countersunk bolts but countersunk nuts seem to be non existent or that's my opinion!?
I live in Germany.
That sounds possible. I sized the threaded standoffs to be equal to 2x the thickness of the material I was working with. It's possible to get shorter sizes. McMaster-Carr has got a huge selection, it would depend on what thickness of material you were working with and whatever other design constraints you have. You should be able to get a shallow enough standoff that a countersink screw would thread into it and end up with a joint that was flush on both sides.
The head on the standoff is between .018-.023 . I have worked at PEM place for 20 years.