How to relearn and reset TPMS (tire pressure monitor sensor) light on 2009-2014 Ford F-150

Поделиться
HTML-код
  • Опубликовано: 28 июл 2020
  • You can reset TPMS (tire pressure monitor sensor) light on 2009-2014 Ford F-150 IF none of your sensors are bad. Follow these easy steps
    ❗️If you find this video helpful, I would appreciate a $uper Thanks that can be found below the video.
    How To Check The Transmission Fluid On Ford F-150 With Aftermarket Dipstick
    • How To Check The Trans...
    💰Save money on your car/truck maintenance and repairs:
    Top 3 Reasons Why Your Car Won’t Start
    • Top 3 Reasons Why Your...
    Don't let Timing Belt Failure Happen
    • Don't let Timing Belt ...
    Look what happens when you neglect your engine oil
    • Check and Change Your ...
    Check your Engine, Coolant, Transmission, Power Steering Fluid, and Brake Fluids
    • Check Your Car Fluid L...
    Blown Head Gasket - Don’t Neglect Your Cooling System- Look What Happens
    • Blown Head Gasket - Do...
    What Does Engine/ Serpentine Noise Sound Like And What Does It Mean? - Squeaking & Squealing Noise
    • Serpentine Belt Squeak...
    Always make sure your lug nuts are TORQUED and not done with an impact gun
    • Don't Use This When Ch...
    How to diagnose and replace wheel bearing going bad on any car
    • Whining, Grinding Nois...
    Learn why the tire pressure is important and how to check it in your car
    / bm8wnjripj
    Remove and replace Broken or Stripped Wheel Stud on most cars
    • Broken or Stripped Whe...
    Cheap Way To Check For Bent Valves Without Removing Cylinder Head
    • Cheap Way To Check For...
    Fast and Easy Way to Restore Faded Car Paint and Scratches - With Minimal Tools
    • Fast and Easy Way to R...
    The Best Way To Fix & Repair Broken Wire in Your Car - Soldering Car Wires Together
    • The Best Way To Fix & ...
    💰Save money on other Ford F150 maintenance and repairs :
    The most effective way to find a leak in Ford F-150
    • Ford F-150 cab water leak
    How to relearn and reset TPMS (tire pressure monitor sensor) light
    • How to relearn and res...
    Ford F-150 Transmission Problem? Might be an Easy Dry Shaft Fix
    • Ford F-150 Transmissio...
    How to find your security keyless entry keypad code on Ford F150
    • How to find your secur...
    How to Remove Ford F150 Fronts Seats
    • How To Remove Ford F15...
    How to unlatch rear seat back on 2009-20014 Ford F-150
    • How to fold down rear ...
    How Remove Ford F150 Inside Door Panel
    • Ford F150 Interior Doo...
    The Removal and Installation of Door Lock Actuator, common failure on F150
    • Replacement of door lo...
    How to Replace Blinker Bulb on Ford F-150 2009-2014
    • How to Change Turn Sig...
    Review, installation, and testing of GTR Lighting ULTRA 2 LED: H13 Headlights for 2009-2014 Ford F150
    • Review, installation, ...
    Review and installation of LASFIT Pro series Custom Design LED headlights for 2009-2014 Ford F150
    • Review and installatio...
    Ford F150 Gas Cap won’t stay closed? Permanent Fix!
    • Ford F150 Gas Cap won’...
    ⁉️QUESTIONS
    If you have any questions or I missed something, comment below and I’ll answer and try to help you out
    If you find this video helpful, like it and subscribe to my new channel. I’ll have tons of videos on all kinds of car and truck repairs in the
    future.
    ⚠️Disclaimer:
    The videos on Motorcarnut channel are posted with informational purpose only.
    Information posted in this video does not guarantee any particular result. Use this information provided in the video with caution and at your own risk. It is the responsibility of the viewer to take this risk.
    Motorcarnut is not responsible or liable for property damage, any loss damage, or injury related to or resulted from information posted in this video.
  • Авто/МотоАвто/Мото

Комментарии • 157

  • @Alexisordaz
    @Alexisordaz Год назад +9

    What a G! Mine just came up out of no where as I was driving and went straight to RUclips. Man people like you keep the world turning

  • @mjheredia1
    @mjheredia1 Год назад +10

    i TRIED IT AND i WAS AMAZED THAT IT WORKED , THANK YOU FOR BEING OUT THERE

  • @Jeffrey-Flys
    @Jeffrey-Flys Год назад +8

    First video that actually explained the whole process. Thank you!!!

  • @mansooralmahruqi885
    @mansooralmahruqi885 Год назад +6

    You deserve our thanks.
    May Allah(God) keep you safe and always show you the correct way

  • @80s-Rock
    @80s-Rock Год назад +4

    Thank you for the knowledge this worked on my 2011 f150.

  • @Cristianlw
    @Cristianlw Год назад +1

    Thanks man! Video was to the point and actually worked.

    • @Motorcarnut
      @Motorcarnut  Год назад

      Glad it helped! Thanks for the comment!

  • @michaelrobertson8795
    @michaelrobertson8795 10 месяцев назад +2

    Thank you very much this thing's been pissing me off for a long time I thought it was dead batteries in the sending units.👍✌

    • @Motorcarnut
      @Motorcarnut  10 месяцев назад +1

      Glad it helped out! And appreciate the feedback!

  • @Odessinto
    @Odessinto 2 года назад +2

    Tnx so much for helping people with this ! I got the same problem and I didn't try yet but for sure should work)

  • @vangbrosoutdoor9055
    @vangbrosoutdoor9055 Год назад +1

    This video worked for me. Thanks a lot.

    • @Motorcarnut
      @Motorcarnut  Год назад

      No problem, thanks for the comment

  • @SOHAIL50280
    @SOHAIL50280 Год назад +1

    So helpful for us this video thanks brother

  • @josephrivera2378
    @josephrivera2378 5 месяцев назад

    Perfect tutorial, worked like a charm. Ty!!

    • @Motorcarnut
      @Motorcarnut  5 месяцев назад

      You're welcome! Appreciate the feedback!

  • @davidlmatteson
    @davidlmatteson 2 года назад +1

    Worked for me, thank you!

  • @nicholaswillcox
    @nicholaswillcox 26 дней назад

    Thanks, boss. Sorted in under 10. Much appreciated.

    • @Motorcarnut
      @Motorcarnut  25 дней назад

      No problem 👍 thanks for the feedback!

  • @user-ci7gf8nj2h
    @user-ci7gf8nj2h Год назад +1

    Thank you so much and God bless you ☺️

    • @Motorcarnut
      @Motorcarnut  Год назад

      You are so welcome, and thank for the feedback

  • @martinvillarreal6542
    @martinvillarreal6542 3 года назад +1

    It worked, thank you very much

  • @Ms.T302
    @Ms.T302 2 года назад +1

    Thank you 💞

  • @andrewmasty1538
    @andrewmasty1538 2 года назад +1

    Thanks it worked

  • @stephenskierski5633
    @stephenskierski5633 2 года назад +1

    Thanks!

  • @bowesman1000
    @bowesman1000 Год назад +3

    Do you have to overfill the tires first? might help if you would explain. if you start with 35 psi , at what point do you get the beep and then you have to refill them again I assume. little vague on the procedure.

    • @Motorcarnut
      @Motorcarnut  Год назад +5

      You start at around normal pressure 36psi and you let air out of each tire until it beeps. And then add air back up to 36psi or where you keep proper tire pressure for your vehicle. If it never beeps and tire is almost flat then you have a bad sensor.

  • @brandon2lj
    @brandon2lj 2 года назад +3

    sweet. worked perfectly on my 2014 f150. thank you!

    • @Motorcarnut
      @Motorcarnut  2 года назад

      Glad it helped

    • @nickcoles5240
      @nickcoles5240 Год назад +2

      What did u pressure the tires up to before you dropped them down for the horn

  • @FrankieWellman
    @FrankieWellman 3 года назад +2

    I have a 2009 Ford F-250 and I was able to get it into training but when letting air out of the first tire the truck would not honk. I tried twice and now I need to get air in my tire. I suspect that means that the left front tire has a bad sensor?

    • @Motorcarnut
      @Motorcarnut  3 года назад +1

      Yes, it’s probably a dead battery, bad sensor

  • @matta785
    @matta785 6 месяцев назад +1

    Thank you! I echo what everyone says! One question on something I ran into. I got this process started but once it got me to right front tire I let air out of it and it never honked to move onto the rear passenger tire. I got down to 30 psi on the right front tire (max 51psi). Any idea what may cause that? Do I have possibly a bad sensor on that tire?

    • @Motorcarnut
      @Motorcarnut  6 месяцев назад

      Thank you too!
      Yes it does sound like a bad sensor

  • @papaguche
    @papaguche 2 года назад

    Thanks.

  • @angellomito2010
    @angellomito2010 3 года назад +2

    So if it horn twice means that I have a bad sensor? Do I need a whole new tire? Thanks

    • @Motorcarnut
      @Motorcarnut  3 года назад +2

      Yes or you didn’t complete the cycle properly. Not a whole tire just the sensor

  • @stevenwaller192
    @stevenwaller192 Год назад +1

    So I have question. I just had three sensors replaced. Mechanic said to drive 20 + miles and the light would reset ( it hasn’t yet) !
    Were they supposed to do this re- learn or do it with a scan tool?

    • @Motorcarnut
      @Motorcarnut  Год назад +1

      New sensors have to be reprogrammed into the vehicle’s computer, THEN relearned with scan tool.

  • @lugo2214
    @lugo2214 Год назад +2

    Hi do you have to refill the air to operating Preasure after the reset?

    • @Motorcarnut
      @Motorcarnut  Год назад +1

      Yes, never drive without the proper tire pressure.

  • @ConkysFlippinAdventures
    @ConkysFlippinAdventures Месяц назад +1

    It worked on my 2014 F-150. Horn doesn't work so I just listened for the chime when the horn would have come on.

    • @Motorcarnut
      @Motorcarnut  Месяц назад

      Awesome! Thanks for the feedback

  • @cal-yb7fg
    @cal-yb7fg 4 месяца назад

    Awesome

  • @im.sp00ky54
    @im.sp00ky54 10 месяцев назад +1

    Does this work on Ford Expedition 2014? Or do I need a scanner device.

    • @Motorcarnut
      @Motorcarnut  10 месяцев назад +1

      It should, basically the same vehicle.

  • @kevinbyrd67
    @kevinbyrd67 3 года назад

    Will that procedure work for a 08 f 150 limited?

  • @SheenaRea
    @SheenaRea 28 дней назад +1

    I just had all 4 tires replaced (rims and tires) last week on my 2009 Mercury Milan. Drove the car a little here and there, and today I get this tire sensor fault message. Do I have to go back to the tire dealership and have them reprogram the tires? Thanks for the video, very helpful. 🙂

  • @markkenward7040
    @markkenward7040 2 года назад +1

    Will this work if I install NEW take offs on my 2013 from a 2021 F150. If not, is there a procedure?

    • @Motorcarnut
      @Motorcarnut  2 года назад

      Not sure if the sensors are the same, you would have to research that. If they are different just install your old sensors in the new wheels

    • @markkenward7040
      @markkenward7040 2 года назад

      @@Motorcarnut Yes, I could do that, but the last time I broke down a car tire was in the 50's and we drove over the tire to break it down. Tubes back then, too. I have done many motorcycles, but not cars. I planned to sell my old set. thanks for the reply!!!

    • @Motorcarnut
      @Motorcarnut  2 года назад +1

      No problem

    • @kendallrenfro
      @kendallrenfro Год назад

      Did you ever figure out if they would work?

    • @Motorcarnut
      @Motorcarnut  Год назад

      2021 sensor are different from 2013

  • @nzs316
    @nzs316 3 дня назад +1

    But, no mention as to the starting tire pressure. Do you inflate to the proper tire pressure then deflate to train?

    • @Motorcarnut
      @Motorcarnut  3 дня назад

      Starting pressure should always be the proper inflation then deflate to train then inflate to proper pressure when done.

  • @charly4291
    @charly4291 7 месяцев назад

    Question when you get out of your truck did you turn off the key?

    • @Motorcarnut
      @Motorcarnut  7 месяцев назад

      While your doing the test?, No

  • @jiggidyjam
    @jiggidyjam 2 года назад +1

    I took my new sensors to discount tires and they programmed and relearned them to my f150 for FREE!

    • @Motorcarnut
      @Motorcarnut  2 года назад +1

      Sounds like a great deal to me

    • @jiggidyjam
      @jiggidyjam 2 года назад +1

      @@Motorcarnut yeah right. I was surprised. Nobody does anything for free these days

  • @Crackheadjones_crack
    @Crackheadjones_crack 3 года назад +1

    So im assuming the tire that wont train is the tire sensor thats out?

    • @Motorcarnut
      @Motorcarnut  3 года назад

      Yes, most likely the battery inside the sensor. They last for 5 to 10 years, some sooner some later.

    • @Crackheadjones_crack
      @Crackheadjones_crack 3 года назад

      @@Motorcarnut thanks

  • @petertimpson9378
    @petertimpson9378 2 года назад +1

    Both front tires had a beep right away. My left rear had a lot more air released and then I heard 2 beeps of the horn. left rear almost all air out but no beep. It said low air pressure on dash.

    • @Motorcarnut
      @Motorcarnut  2 года назад +1

      Sounds like you may have a bad sensor. The 2 beeps probably made the system end before learning.

    • @user-vb9tn8lk3h
      @user-vb9tn8lk3h Год назад +1

      ​@@Motorcarnut

  • @lafaina79
    @lafaina79 3 дня назад +1

    Then is this the right pressure or need to top up afterwards?

    • @Motorcarnut
      @Motorcarnut  3 дня назад +1

      Need to inflate to proper pressure again

  • @greg10469
    @greg10469 8 месяцев назад +1

    Have 2013 f150 to reset light all I did was fill tires to correct pressure (35) unhook negative battery turn lights on..reconnect battery, started truck and yes the light was still so I drove it 1/2 mile and the low tire light turned off...all on its own.

    • @Motorcarnut
      @Motorcarnut  8 месяцев назад +1

      There was probably nothing wrong with yours.

  • @jamesbarber2040
    @jamesbarber2040 2 года назад +1

    I tried this and I released so much air and the horn never went off..I purchased newer tires and rims off road and had new sensors put in and the warning came up,they tried to recalibrate it and nothing..I took it to ford and they said the rear ones are bad..I took it back and they decided to put my original tpms on the new rims and tires same issue which worked with my original factory tires andrims..Can someone tell what's the problem,before I go back to ford...Thanks

    • @Motorcarnut
      @Motorcarnut  2 года назад +2

      The sensors probably have to be reprogrammed then relearned.

    • @jamesbarber2040
      @jamesbarber2040 2 года назад +1

      @@Motorcarnut TY
      .

  • @vsujones
    @vsujones 2 года назад +2

    Is there a way to find out if you have a bad sensor besides this?

    • @Motorcarnut
      @Motorcarnut  2 года назад +1

      Yes, with a scan tool.

    • @vsujones
      @vsujones 2 года назад +1

      @@Motorcarnut ok I used it and got the code. So I did the relearn and I will see it that fixes it because they all beeped

    • @Motorcarnut
      @Motorcarnut  2 года назад +1

      If you got a code that should be taken care of first.

  • @randyclar747
    @randyclar747 Год назад +1

    Are you letting all air out or just some?

    • @Motorcarnut
      @Motorcarnut  Год назад +1

      As much as needed until it beeps. After you finish all 4 wheels you have to add air to proper specs for your vehicle

  • @Gtown1777
    @Gtown1777 3 года назад +12

    So, it worked BUT, I had to let out a lot of air on LF. Then after the error cleared when I completed the process, the error came back after a few minutes. Likely because my LF is low after letting so much air out. LESSON, don't do this unless you have an air compressor nearby to refill your tires.

    • @Motorcarnut
      @Motorcarnut  3 года назад +1

      Good point!

    • @ace03cobra67
      @ace03cobra67 2 года назад +4

      I was doing this and from 40psi and to 30 psi . And still no horn sound I was like let me do this later when I get to the gas station first

  • @jonathanjacobs5313
    @jonathanjacobs5313 Год назад

    Do you have to add the air back afterwards?

    • @Motorcarnut
      @Motorcarnut  Год назад

      Yes you do and sensors are different and have to be replaced

    • @djwilson48625
      @djwilson48625 Год назад +1

      My brain just locked up reading that..... Seriously?

    • @bowesman1000
      @bowesman1000 Год назад

      @@djwilson48625 mine did also .

  • @salvadorluna64
    @salvadorluna64 3 года назад

    Does the horn go off on every tier

  • @JimmyCasket02
    @JimmyCasket02 29 дней назад +1

    Does this work for new sensors?

    • @Motorcarnut
      @Motorcarnut  29 дней назад

      No you have to reprogram them first with a scan tool.

  • @Eben18
    @Eben18 2 года назад

    Do you have a video for a 2008

    • @Motorcarnut
      @Motorcarnut  2 года назад +1

      Sorry I don’t

    • @Eben18
      @Eben18 2 года назад

      @@Motorcarnut thank you, I found a video don’t a small tool. I will order it from Amazon and try it out

    • @Motorcarnut
      @Motorcarnut  2 года назад

      Great hopefully it will work!

  • @kato2182
    @kato2182 Год назад +1

    I didn’t know rotates now i cant get it to relearn with the scan tool so im trying this

    • @kato2182
      @kato2182 Год назад +1

      It worked light is off hell yeah

    • @Motorcarnut
      @Motorcarnut  Год назад +1

      Lol, great it helped!

  • @turo669
    @turo669 6 месяцев назад

    So do I put extra air then let out??

    • @Motorcarnut
      @Motorcarnut  6 месяцев назад

      Fill to proper inflation then let it out as stated in video. Once it’s complete refill to proper inflation again

  • @ejhybrid1071
    @ejhybrid1071 2 года назад +1

    What do you do if one of them actually does not work?

    • @Motorcarnut
      @Motorcarnut  2 года назад +1

      Either that one has to be reprogramed then relearned or replaced.

    • @ejhybrid1071
      @ejhybrid1071 2 года назад +1

      @@Motorcarnut how does one reprogram it???

    • @Motorcarnut
      @Motorcarnut  2 года назад +1

      It requires a tpms scan tool

  • @nedabd9286
    @nedabd9286 3 года назад +1

    I tried and i did
    All the steps first tire 👌 put the passenger side didn't work

    • @Motorcarnut
      @Motorcarnut  3 года назад +1

      Probably that passenger side sensor is bad

    • @fisher9915
      @fisher9915 3 года назад +4

      May be a stupid question but with all the air you let out of those tires I would think the light should be on until you air them up to correct psi.

  • @jiggidyjam
    @jiggidyjam 2 года назад

    I installed new ones for my 2014 f150but can’t get it to relearn

    • @Motorcarnut
      @Motorcarnut  2 года назад

      You have to reprogram them first before the relearn and need a scan tool to do it.

    • @jiggidyjam
      @jiggidyjam 2 года назад

      @@Motorcarnut k thx

  • @rollyduncan
    @rollyduncan 3 года назад +3

    I tried this. Driver honked once. Got to my passenger side the horn honked twice. And it said to repeat test. inflated all back to proper psi. And ran test again and passenger side honked twice, that tells me that my battery is DEAD. Just logic here folks

    • @Motorcarnut
      @Motorcarnut  3 года назад +5

      Dead battery means failed sensor as i stated. Battery is not replaceable. But to be 100% sure you need to "look" at the sensor data with a scan tool which is not what this video is about.

  • @AnAmericanGuitarist
    @AnAmericanGuitarist 3 года назад

    how do you hit "OK"?

    • @Motorcarnut
      @Motorcarnut  3 года назад

      On the left side of the steering wheel there’s a square button with the “ok” in the middle you press.

    • @AnAmericanGuitarist
      @AnAmericanGuitarist 3 года назад

      @@Motorcarnut Thanks

  • @user-zh6om8ti5m
    @user-zh6om8ti5m 2 месяца назад

    Had this notification for a while on my truck, and recently my husband had the four wheels replaced (new rims also, everything bigger than the original) by a small local shop nearby. How is the truck able to to detect new, bigger tires installed?

    • @Motorcarnut
      @Motorcarnut  2 месяца назад

      It won’t unless they installed the original sensors in their original locations. Plus larger diameter tires will throw the mph off a little.

  • @rachellashomb2129
    @rachellashomb2129 3 года назад +1

    This didn’t work on my 2009 Ford F-150 :((

    • @Motorcarnut
      @Motorcarnut  3 года назад +1

      If it didn’t work you probably have a bad sensor in one of the wheels.

  • @larryrockett8707
    @larryrockett8707 5 месяцев назад

    What are you pushing to make it okay

    • @Motorcarnut
      @Motorcarnut  5 месяцев назад

      Ok on steering wheel

    • @larryrockett8707
      @larryrockett8707 5 месяцев назад

      @@Motorcarnut the only okay is next to the phone symbol on the steering wheel

    • @Motorcarnut
      @Motorcarnut  5 месяцев назад

      Correct or the hazard button depending on what year you have.

    • @larryrockett8707
      @larryrockett8707 5 месяцев назад +1

      Thank you very much

    • @Motorcarnut
      @Motorcarnut  5 месяцев назад

      @larryrockett8707 no problem

  • @jimhagstrom5595
    @jimhagstrom5595 11 месяцев назад

    2011 F150 Lariat doesn't work. All new sensors and it doesn't notice when removing air

    • @Motorcarnut
      @Motorcarnut  11 месяцев назад

      Then you need to reprogram them to the vehicle first then relearn them to each wheel

    • @jimhagstrom5595
      @jimhagstrom5595 11 месяцев назад

      @@Motorcarnut I'll give it a try

    • @tonyreid2397
      @tonyreid2397 2 месяца назад

      @@Motorcarnut And how do you do that?

    • @Motorcarnut
      @Motorcarnut  2 месяца назад

      With a scan tool or tpms tool

  • @michaelrobertson8795
    @michaelrobertson8795 10 месяцев назад

    It was my dad's truck and he passed away and mom didn't know how to fix it and dad did have the tires rotated

    • @Motorcarnut
      @Motorcarnut  10 месяцев назад

      Sorry for your loss. I’m glad this helped you!

  • @TheRoadliner69
    @TheRoadliner69 3 месяца назад

    I guess I’m the bad Apple of the bunch because this didn’t work for me. I went to train the front tire and let the air out two times and both times the horn blew, but it said retrain. 🤷🏼

    • @Motorcarnut
      @Motorcarnut  3 месяца назад +1

      Can be a bad sensor itself.

  • @Twin-Nick
    @Twin-Nick 2 года назад

    Sir... I have flown halfway across the world just to attend a church in England and while I was there I had a conversation with a church-mouse who spoke louder than you. Please speak up or clear your microphone.

    • @Motorcarnut
      @Motorcarnut  2 года назад +4

      If you're having conversations with church mice you have bigger problems than the volume in my video.

    • @Twin-Nick
      @Twin-Nick 2 года назад

      @@Motorcarnut I'm kidding lol.

    • @Motorcarnut
      @Motorcarnut  2 года назад +1

      Me too, lol

  • @timdykes5228
    @timdykes5228 2 года назад

    To slow

    • @Motorcarnut
      @Motorcarnut  2 года назад

      That’s the procedure without any tools. And most people don’t have tpms tools or a scan tool.