Glad it helped And thank you so much for your great support and sharing my dear friend...!!! If you wish to get any support, you can contact our team using our website.
when you save this exercise and open again, try to verify immediately connection between PC3 and PC4 or PC5 an you can check it doesn't work , WHY NOT? thanks for your video give you my like, and subscription.
10:28 (was that a rooster?) These are amazingly helpful. I see how far I can go with what I've learned, and when I run into a roadblock.... I watch your walkthrough and find out where I went wrong. Thank you
Hello TechAcad Team, I am now starting my CNNA 200-301 course and I would like to know where to find the commands for the various configurations that exist for a Switch (I hope I used the right term) to be able to train. Thanks to share your knowledge
We have the video regarding the basic configuration of switches. Please have a look with it. If still needed support, you can contact our team using our Website.
On mine, PC5 will ping the MLS ipv6 addresses just fine, but refuses to ping PC3 or PC4. I've triple checked the ipv6 addresses and they are the correct ones. Any thoughts?
Thank you so much sir this is very helpful! I have a question: when I left the IOS Command Line Interface for too long, the process ended automatically and I need to start again from for example MLS> . But why I don't see that happen to you?
Thank you Tech Acad for your Great video. I can not ping between Switches. I have vlan 99 on all Switches but unable to ping with each other. Do you know where to check? Shall I create trunk on all Switch interfaces?
Make sure that you given the IPv6 address in the correct format! Avoid copy paste And thanks for your great support and sharing our channel with your friends too!
Hello Sir, when i do switchport mode trunk on MLS, it's showing: Command rejected: An interface whose trunk encapsulation is "Auto" can not be configured to "trunk" mode.
By far the best tracer classes on RUclips..I def use you instead of check results
Thank you so much Tech Acad! I was struggling in this class until I found your channel!
Great to hear!
Thank you so much tech acad. By watching your packet tracer videos I have been getting 100% in my networking practicals!
Great to hear!
As usual Tech Acad. You're the man! 100% completion.
You rock!
thank you so much the video is the greatest lession i've ever learnt helping my homework so much
Glad it helped!
you guys are heaven sent
Glad it helped
And thank you so much for your great support and sharing my dear friend...!!!
If you wish to get any support, you can contact our team using our website.
when you save this exercise and open again, try to verify immediately connection between PC3 and PC4 or PC5 an you can check it doesn't work , WHY NOT? thanks for your video give you my like, and subscription.
10:28 (was that a rooster?) These are amazingly helpful. I see how far I can go with what I've learned, and when I run into a roadblock.... I watch your walkthrough and find out where I went wrong. Thank you
Glad it helped!
LL look LL
LL
LL look LL LL loll
LL l
Hello TechAcad Team,
I am now starting my CNNA 200-301 course and I would like to know where to find the commands for the various configurations that exist for a Switch (I hope I used the right term) to be able to train.
Thanks to share your knowledge
We have the video regarding the basic configuration of switches. Please have a look with it. If still needed support, you can contact our team using our Website.
Thankyou , this clarify a lot of the confusing i had
Glad you like them!
And thank you so much for your great support and sharing our channel with your friends!
Very good video. Your videos are always great.
Glad you like them!
very helpful to me as a student in Cisco
Really Glad to hear it!
Excellent video bro
Thanks for your great support and sharing my dear Friend...
Clear Explanation Sir , Thankyou
So nice of you
Amazingly helpful yet again! Thanks!
Glad to hear it!
i really like your video its my request make a video on stub area totally stubby area.
Ok. Thanks
Thanks. Another great video.
Thank you so much for your great support and sharing my dear Friend...
On mine, PC5 will ping the MLS ipv6 addresses just fine, but refuses to ping PC3 or PC4. I've triple checked the ipv6 addresses and they are the correct ones. Any thoughts?
thank you this video helped me a lot :)
Glad it helped!
Thank you so much sir this is very helpful!
I have a question: when I left the IOS Command Line Interface for too long, the process ended automatically and I need to start again from for example MLS> . But why I don't see that happen to you?
There is a command to avoid it. It is called "line console exec-timeout".
@@TechAcad Thank you sm!
I have a hands on test coming up for my class and Im not sure if what I do here is whats required for the test can you help
Please contact our team using our website. Link will get from the description.
Thank you Tech Acad for your Great video. I can not ping between Switches. I have vlan 99 on all Switches but unable to ping with each other. Do you know where to check? Shall I create trunk on all Switch interfaces?
Please follow the instructions correctly and troubleshoot it if any trouble!
How did you configure the cloud on the cluster trying to that but I can't ping it any help would be helpful
try to explain more this looks like reading the exercise
Sure, We will
And thanks for your great support and sharing my dear friend....!!!
My SW2, SW3 and SW1 can't ping each other, please what configuration did i omit?
I keep getting an error when I enter the ipv6 address for the g0/2 interface even tho I copied it from the table. Any tips?? Nice vid btw!
Make sure that you given the IPv6 address in the correct format! Avoid copy paste
And thanks for your great support and sharing our channel with your friends too!
Thx again
Glad it helped...
Hello Sir, when i do switchport mode trunk on MLS, it's showing: Command rejected: An interface whose trunk encapsulation is "Auto" can not be configured to "trunk" mode.
configure "switchport mode dynamic desirable" first
I m first viewer great
Thank you so much for your great support friend...
Hello
How you connect MLS to cloud using G 0/2 at cloud side?
Because when i am trying to connect it but there is no option of gigbit on cloud side
use cluster, not cloud
Thanksss !!!!!!!
Glad it helped!
Thanksyu 🙏
Welcome 😊
How did you create the cluster
They are predesigned pka files
Why we creat native vlan 99
Can u explain mee
native vlan is for untagged frames. And we can any vlan number for this native VLAN.
Bro in the last part of configure g0/2 with ipv6 on mls i keep receiving an error overlapping
Overlapping is due to configuring the same Network in the router!! Please verify the IP Address.
@@TechAcad Thank you so much I configure a wrong ip add so it keeps saying overlapping