The batteries!!! After wasting a bunch of time trying all 57 codes for a Samsung TV twice... I found your video... I changed the batteries in the remote and got the stupid code on the very first one! Thank you man! Awesome video!!
That's awesome! I don't remember if I said to make sure the batteries are good on this particular video, but I generally do say that in my other videos...😊. Thanks for the great feedback..
6 years later and still helping! I’m on vacation and remote 2 wasn’t working. I’ve never had dish before but Now I have 2 little boys happy that they can watch their cartoons. Ty!
I don't know if you'll ever see this, but I love you 😂. I kept trying to program and the button lights kept flashing ! I found your video and you said *check the batteries* bingo. The remote was working every other way, but not for programming. So I'll say it again: I don't know you, but I love you.😉😄
THANKS! I programmed my Dish remote to control my old Toshiba TV, my Apple TV and my Sony DAV DX150 amplifier (surround sound). Started with four different remotes, down to one! Thanks again.
So I called Dish tech support and after some really bad troubleshooting by them they tried to upgrade me to a newer receiver. I said no thank! Watched your video and got it all sorted put and working correctly 👍
I worked with Dish as a technical support representative and your video reminded me of the steps needed to perform in order to program the remote. Hahahahahaha
Thank you . Your advise to replace the remote batteries made all the difference. I was ready to give up. Changed the battery and the remote blinked differently than it had been, punched in one of the same codes I already tried and bingo, it worked and the light blinked three times. Thanks again.
HI, it's been a while since I've had access to a dish receiver. I seem to remember the UHF remote has an address that has to match the receiver. I believe if you google setup dish UHF remote, it'll take you to the dish website with the instructions of how to do that...
I’m so grateful I came across your video. After going to the dish home page and watching other videos, yours was the only one that worked! Thank you!!!🥳🥵
Excellent advice on the batteries. Two dish techs failed to catch that. Popped in the new batteries and voila! the first code worked. Time to take a bath.
You made it easy. O matter how many times I reread the instruction manual to program my dish 21.1 remote, it didn’t make sense. First time I watched your video, it worked. Thanks for sharing your knowledge.
The key is to make sure the device is broadasting an IR signal if that is what you need. It can't be seen with naked eye but if you use your telephone and view the front, with it, you can confirm remote is broadcasting an IR signal! Some dual purposes remotes need to have battery compartment opened and the base above it pulled out and flipped and pushed back in, in order to issue IR signal. Very important first step!
HI, Here's a link to the official Dish Page to "Teach" a remote... I don't know if this is the right one for the specific remote that you have, but it's a place to start: my.dish.com/support/products/remotes/customizablecommands
I bought a new remote from Amazon but it only has the number one key at the bottom...and it only now works on my living room tv and I need it for the bedroom tv (tv2)....do I need to buy a remote with the number 2 key at the bottom?
HI... Usually with these remotes wherever the physical box is located is going to be the number 1 remote. The number 2 remote is going to be the location where there is no box and works with RF to transmit a signal back to where the box is located. If that makes sense...
Honestly, you said better than the dish website because they were saying something totally different. Thank you so much for this video and now I can use just one remote!
Is there an automatic code search function in the remote? I don't seem to find the right code for my old tv. I found the auto code search on another old remote but couldn't figure out how to do it on this remote. Thanks
I'm not sure on this remote.... I believe it's teachable if you have your original.. This page is the Dish page for programming remotes. It'll say something if it does that: my.dish.com/support/products/tv
Thank you! Had an old Dish remote laying around that I was able to use with a $20 TV that I bought today at a thrift store! Saved me from buying a universal remote!
Hey I’m hoping you can help me So I just got a Philips tv and I hook the dish satellite cable up and it shows on my tv but my remote won’t work I try to reprogram and replace batteries but it still won’t Turn my satellite on can you please help me
Hi, Is that a new remote to your DISH receiver box? IF so, it may have to be programmed to the box. If it's an existing remote that worked before, try rolling the batteries with your fingers... Sometimes the batteries can loose connection. Even if their new. It's possibly a bad remote...
I use my "AUX" device button to turn on/off and control the volume of my amplifier (the TV audio is fed to this device). How can I program my 20.1 IR remote to automatically increase/decrease the amplifier's volume without having to switch from "SAT" to "AUX" each time? Thanks & Blessings
Excellent!... Thanks Duane, you beat me to the answer...! Here's a link to the manual I found, if someone out there doesn't have the manual handy.... www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=1&ved=0ahUKEwjk5pCwmdbZAhVNneAKHRcOCYcQFggoMAA&url=https%3A%2F%2Fwww.mydish.com%2Ffilestream.ashx%3FID%3D3037&usg=AOvVaw07BVO2Cbc4TFc4m5mBc_dV
Excellent, thanks so much for your video. I insisted in trying different codes until I replaced the batteries as you said (duh, why I didn't listened in the first place? 🙄). Thank you sir.
Hey do you have any codes for a 32"westinghouse model number UW32S3PW. version TW-69901-U032H. This model has only 1 button on it, on/off need a code to add to my universal remote. Plz hlp.
Dish Remote - has to be 6-7 inches - from TV itself (volume change) or Box ( to change channel). It stopped working from a "distance" (like say "the couch). Have to get up with remote right next to either TV or box. WHY? What happened? Was fine.. then overnight...lost distance (??
yes yes even the 9.99 rechargable ones. Funny sometimes says "Battery Low" on the screen- even with new or charged batteries. I resorted to the TV (LG) remote for volume & mute (that works from 'couch distance'. But still have to walk right up to Dish receiver with Dish remote- to change channels @@JLPicard440
SOLVED! It was the Remote. I was able to Program the New one they sent me- and all distance issues- healed. The old Remote (altho it lit up was Shot! thanks and shout out to See World Satellites in Indiana Pa.!!! @@JLPicard440
Yes I was going to suggest that after I asked about the batteries! Sorry I didn't see your comment yesterday or I would have answered sooner. Glad you got it going again.. 😀
I only came here to program my replacement Dish remote and so happy to also use my Apple TV with my Dish remote too. Always losing that little Apple remote! Thanks for great video.
Thanks @Take A Bath Productions, my Sharper Image Sound Bar remote programmed perfectly to my Dish remote! Learning Mode was a great tip you have in this video! Thanks again! :-)
Yes u can... I don't have the codes but they're easy to look up.. you can google remote codes for dish remote and it should come up.. I might have left a Link in the description as well..
I was able to change the number 2 to 21 on the system setup. I have an insignia roku tv and teying to pair with a dish remote. I don't have a hopper. Everything seems to have worked EXCEPT I cant get the dish remote to turn back on and have dish to come on. When I power off and then back on the roku home page comes in. How do I change this?
It sounds like you have to setup a macro command which is a series of commands that will execute multiple functions with one button press. I can't remember if this remote can do that or not..
I go my BOSE sound bar programed into my DISH remote but have to switch ti AUX everytime I want to vol up or down! Can you help me keep it in SAT mode ti do it all?
I hope this helps. Here's an excerpt from an older Dish Manual: When the remote control is set up to operate your TV, the MUTE and VOLUME buttons adjust your TV volume when in SAT mode. To use the remote to adjust the volume of a remote-controllable audio receiver or amplifier instead of adjusting the TV’s volume setting, use the steps on this page. * Press and hold AUX until all Mode buttons are lit, then release it. The AUX mode button flashes. * Press POUND (#). * Press the plus (+) side of the VOLUME button. * Press the 0 number button. * Press POUND (#). The AUX mode button flashes three times. Make sure the remote adjusts the amplifiers volume in other modes: * Press SAT. * Press the plus (+) and minus (-) sides of the VOLUME button. * Your tuner/amplifier’s volume changes, and the AUX mode button lights.
Oh Snap my remote has learning! Solved my issues with a new element tv that wouldn't take codes and soundbar that would shut down and Id have to use a separate remote just to turn back on.
Programming the remote works for volume, mute and on/off. However, it does not work to change the programing from HDMI to TV mode. I have an external antenna for local channels which is the TV mode. Pressing the TV button on the side of the remote does not allow switching from HDMI to TV mode or programming. However, pressing the SAT button on the side of the remote does change from TV programing to HDMI programing. Why shouldn't work for TV programing?
HI. You must have a Hopper with the black dish remote 54.0. That's the only dish remote I know of with the buttons on the side. I do have a hopper video programming the remote to different devices. There's also a input button on the side of the remote. Did you try putting the remote in TV mode and then pushing the input button to see if it'll switch inputs from HDMI to Air/TV?
Volume did not work: Had Sat set up all was good tried Volume with first code on list no go, but then used another code listed on new remote sheet and she works as she is suppose to....Great info thank you 👍👍👍👏👏👏🇨🇦
I don't remember exactly. Are there 2 addresses? 1 for the IR main remote and then a 2nd one for the RF remote to the other room? Is the primary remote setup to receive from the RF remote? That could be what's wrong...
Ok, i'm trying to program my 20.1 IR remote to my tv. i hold the tv button, the lights flash, and then stop. i put in the code, press pound, and nothing happens. is this because of batteries, or something else?
@@JLPicard440 it works fine for the satellite, the "low battery" notification hasnt come on. and i got the list of codes off of dishes site and went down it. i followed the steps on the website, when i hold the tv button down, the lights all blink 3 or 4 times and then they all turn off, and where it says to input the code and press # and the tv light will blink, the tv light doesnt blink
@@codussigma Just because the Battery low light hasn't come on doesn't mean the batteries are fresh enough to program. It's still worth a try if you have some new ones laying around. There's only 3 choices of what could be wrong.. 1. You're doing something wrong when you program it. 2. The batteries are low 3. There's something wrong with the remote itself. There's no other choice!
Usually you can change the channels for the secondary TV in the menu of the dish box. I think mine was set to 73. But if your TV is in the same location as the box, it's probably connected via HDMI cable to which ever input it's connected to. HDMI 1, 2... etc.
@@JLPicard440 not the remote how to install 2nd tv with 722k reciver on the back there is no wire to hook up to the other tv how is the signal being sent to the other tv?
@@eastovercitgo3295 oic... that's a little more complicated than I can explain in a message. If you Google wiring diagram for dish 722 2nd receiver it should bring up a picture so u can see what to do... hopefully this will help...thanks
I have a Samsung HDMI Model UN324500MF and I have it connected to a DISH Hopper. I want to be able to use my DISH remote to change source from DISH to HD ANTENNA. We have hurricanes in South Florida and I want to be able to use the remote to go from CAble to Local TV. Also, we are being told our DISH will no longer cover Local TV. How can I program the remote to move from DISH JOEY to ANTENNA.
I have a dish remote 21.1 IR/UHF Pro remote. It was programmed to turn off my Samsung TV and now it has stopped working and i have re-programmed by entering the remote code and it still will not work. I’ve tried your learned method on the remote without any success. Any suggestions? Do i need a new remote? I’ve tried to call Dish and they were no help. They kept saying that my TV is not compatible with the remote. Which is ridiculous cuz it was working previously.
How can they say Samsung is not compatible...That's a major brand name... what a joke!.. I have a Samsung and it works great. Sorry for the troubles.. did you check the batteries to make sure they're pretty fresh? If you have a different TV, try it on that to see if it works ok. Do you have the original Samsung remote to make sure something didn't happen to the TV itself.. long shot, but you never know...
It should program in the same way as the TV or DVD, I think it goes on the aux device button.... if that doesn't work, I believe the remote is teachable.. if you have the original remote you can teach the commands for the sound bar.
I’m trying to reprogram a 20.1 ir remote to control 2 TVs in one house and then reprogram the UHF to a new tv ina different location. ?? Can u send. A link how to do this.
I think you might be able to put the 2nd TV on the Aux button on the remote. The uhf works on an address that's in the satellite receiver. I don't really have a link you can go to except Dish Network themselves has some info on programming their remotes..This link should get you started.. : my.dish.com/support/products/remotes/how-to/program-to-tvother
Hi I have a sharp tv and a 21.1 ir/uhf pro and I tried every single code on the list on dish website but nothing works. Is there any other way to get it work?
Yes, if you have your original remote, you can teach the dish remote the things you need. Not sure why nothing works. Sharp is a mainstream brand.. It should definitely work with Sharp.
@@JLPicard440 thanks for the response, I contacted customer support and they tried everything they can and said I got a defective remote, so they going to send me another one.
I have remote #2 on my second tv, everything works except for the Volume and Power Button. I’ve tried everything and can’t get them to work. When I try to program the tv and, hold and press tv button , i get the “ Attention - Mode Reminder” every time. CAN YOU PLEASE HELP ME
It could be the remote address. Make sure the remote address is set to the same as the receiver. Try this... ; www.mydish.com/support/products/remotes/how-to/program-to-receiver
It could also be that it is set for remote 2 . If it is a 21.1 , open the battery compartment and find a small toggle . Switch it from UHF to IR . Then the end cap can be pulled and flipped over. One side says 2 and the other says 1 Hope this helps. Thank you Take a Bath Productions for this helpful video.
![Run Away - Tzuyu(TWICE) ツウィ 쯔위 [Music Bank] | KBS WORLD TV 240906](http://i.ytimg.com/vi/KnHNNyAYiu0/mqdefault.jpg)
Spent 45 min. With dish tech and couldn't program new remote . Watched you once & done. No $95 charge for tech to come out. Thank you so much.
That's awesome! I'm glad I could help you. And save a little $$ too... 😀
The batteries!!! After wasting a bunch of time trying all 57 codes for a Samsung TV twice... I found your video... I changed the batteries in the remote and got the stupid code on the very first one! Thank you man! Awesome video!!
That's awesome! I don't remember if I said to make sure the batteries are good on this particular video, but I generally do say that in my other videos...😊. Thanks for the great feedback..
6 years later and still helping! I’m on vacation and remote 2 wasn’t working. I’ve never had dish before but Now I have 2 little boys happy that they can watch their cartoons. Ty!
That's awesome! So glad to help. Enjoy your vacation.. 😎
I don't know if you'll ever see this, but I love you 😂. I kept trying to program and the button lights kept flashing ! I found your video and you said *check the batteries* bingo.
The remote was working every other way, but not for programming.
So I'll say it again: I don't know you, but I love you.😉😄
Hi! Thank you so much for the great feedback... 😀. So glad I could help...
THANKS! I programmed my Dish remote to control my old Toshiba TV, my Apple TV and my Sony DAV DX150 amplifier (surround sound). Started with four different remotes, down to one! Thanks again.
dkenn335 Excellent! Thanks
I
So I called Dish tech support and after some really bad troubleshooting by them they tried to upgrade me to a newer receiver. I said no thank! Watched your video and got it all sorted put and working correctly 👍
That's so cool! Thanks for the feedback.. 😊
Same exact thing happened to me, I said NO THANK YOU .but what I found weird they wanted me to transfer to DIRECT TV
@@L3TITBE Same corporate monopoly??? Just like today’s Banksters or The Lord of the Rings? One RING/chain to rule them all!!!!
I worked with Dish as a technical support representative and your video reminded me of the steps needed to perform in order to program the remote. Hahahahahaha
Roxlee Dimapilis very cool.... I used to install them about 15 years ago and I met Charlie CEO in Phoenix at a meeting for installers
@@JLPicard440lll
Do you know any code for a Toshiba DVD with dish remote I try the 1 is on the page but didnt work
Thank you . Your advise to replace the remote batteries made all the difference. I was ready to give up. Changed the battery and the remote blinked differently than it had been, punched in one of the same codes I already tried and bingo, it worked and the light blinked three times. Thanks again.
TheDavenator7 excellent! Thanks
Cool info. But any idea how to get my tv2 21.1 ufh remote to connect to my dish receiver?
HI, it's been a while since I've had access to a dish receiver. I seem to remember the UHF remote has an address that has to match the receiver. I believe if you google setup dish UHF remote, it'll take you to the dish website with the instructions of how to do that...
I’m so grateful I came across your video. After going to the dish home page and watching other videos, yours was the only one that worked! Thank you!!!🥳🥵
That's awesome... So glad to hear that. You're welcome.. 😊
Thank for this video. Been trying for months to get my sound remote plugged in never knew about the learning feature thank you
Jason Nicholson Guitar Mafia You’re welcome 😊
Excellent advice on the batteries. Two dish techs failed to catch that. Popped in the new batteries and voila! the first code worked. Time to take a bath.
Awesome! Thanks for the comment.. :-)
You made it easy. O matter how many times I reread the instruction manual to program my dish 21.1 remote, it didn’t make sense. First time I watched your video, it worked. Thanks for sharing your knowledge.
Excellent! Thanks for the great feedback and you're welcome.. 😊😁
The key is to make sure the device is broadasting an IR signal if that is what you need. It can't be seen with naked eye but if you use your telephone and view the front, with it, you can confirm remote is broadcasting an IR signal! Some dual purposes remotes need to have battery compartment opened and the base above it pulled out and flipped and pushed back in, in order to issue IR signal. Very important first step!
Good tip! Thank u😊
The learning mode doesn't work on my remote. But mine has a number 1 on it instead of a number 2 like yours?
HI, Here's a link to the official Dish Page to "Teach" a remote... I don't know if this is the right one for the specific remote that you have, but it's a place to start:
my.dish.com/support/products/remotes/customizablecommands
@@JLPicard440 Thank You!
YW! @@bishop2355
I bought a new remote from Amazon but it only has the number one key at the bottom...and it only now works on my living room tv and I need it for the bedroom tv (tv2)....do I need to buy a remote with the number 2 key at the bottom?
HI... Usually with these remotes wherever the physical box is located is going to be the number 1 remote. The number 2 remote is going to be the location where there is no box and works with RF to transmit a signal back to where the box is located. If that makes sense...
Thank you! My Dad was all mixed up and this worked like a champ.
You're welcome!
The battery tip was crucial! Thanks again!
Excellent! You're welcome... :-)
Honestly, you said better than the dish website because they were saying something totally different. Thank you so much for this video and now I can use just one remote!
Glad it was helpful! You're welcome.. 😀
Thank you. You explained it much better than the Dish instructions.
You're welcome... Thanks for the great feedback... 😀
Is there an automatic code search function in the remote? I don't seem to find the right code for my old tv. I found the auto code search on another old remote but couldn't figure out how to do it on this remote. Thanks
I'm not sure on this remote.... I believe it's teachable if you have your original.. This page is the Dish page for programming remotes. It'll say something if it does that:
my.dish.com/support/products/tv
@@JLPicard440 thank you so much for your swift reply
This is the greatest thing ive ever seen
Thank U!
Thank you! Had an old Dish remote laying around that I was able to use with a $20 TV that I bought today at a thrift store! Saved me from buying a universal remote!
Awesome! Glad I could help😊😊
⁰
Man knows what hes talking about thank you
Thank U for the great comment... :-)
Hey I’m hoping you can help me So I just got a Philips tv and I hook the dish satellite cable up and it shows on my tv but my remote won’t work I try to reprogram and replace batteries but it still won’t Turn my satellite on can you please help me
Hi, Is that a new remote to your DISH receiver box? IF so, it may have to be programmed to the box. If it's an existing remote that worked before, try rolling the batteries with your fingers... Sometimes the batteries can loose connection. Even if their new. It's possibly a bad remote...
No sir it’s the same remote in the video
HI... what I meant was is it a new to that box? Or is it the same one that's been working all along?
FINALLY!!! I was able to sync my new TV with my Dish Remote. Thank You!!!
Glad I could help... You're welcome.. :-)
Thank you so much. You helped me in plain English so I could understand. You can read but you taking step by step is so helpful
Glad I could help! You're welcome.. 😊😊
Thanks Howard Stern 👍
No problem 👍
I use my "AUX" device button to turn on/off and control the volume of my amplifier (the TV audio is fed to this device). How can I program my 20.1 IR remote to automatically increase/decrease the amplifier's volume without having to switch from "SAT" to "AUX" each time? Thanks & Blessings
I am so brilliant! I found this PDF that addresses the exact question above. See page 22: DISH+20.0-21.0+Remote+User+Guide.pdf Y"ALL are welcome!
Excellent!... Thanks Duane, you beat me to the answer...! Here's a link to the manual I found, if someone out there doesn't have the manual handy....
www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=1&ved=0ahUKEwjk5pCwmdbZAhVNneAKHRcOCYcQFggoMAA&url=https%3A%2F%2Fwww.mydish.com%2Ffilestream.ashx%3FID%3D3037&usg=AOvVaw07BVO2Cbc4TFc4m5mBc_dV
Excellent, thanks so much for your video. I insisted in trying different codes until I replaced the batteries as you said (duh, why I didn't listened in the first place? 🙄). Thank you sir.
Excellent! Glad you got it going..
Thanks so so much !!! I am horrible with anything technical. I hardly can see and I did it with your video
Glad I could help!... :-)
Hey do you have any codes for a 32"westinghouse model number UW32S3PW. version TW-69901-U032H. This model has only 1 button on it, on/off need a code to add to my universal remote. Plz hlp.
HI, hopefully you saw my other response. Thanks.
Can you do this without a receiver?
HI, not sure what that means?
Dish Remote - has to be 6-7 inches - from TV itself (volume change) or Box ( to change channel). It stopped working from a "distance" (like say "the couch). Have to get up with remote right next to either TV or box. WHY? What happened? Was fine.. then overnight...lost distance (??
Oh wow.... did you try a fresh set of batteries?
yes yes even the 9.99 rechargable ones. Funny sometimes says "Battery Low" on the screen- even with new or charged batteries. I resorted to the TV (LG) remote for volume & mute (that works from 'couch distance'. But still have to walk right up to Dish receiver with Dish remote- to change channels
@@JLPicard440
SOLVED! It was the Remote. I was able to Program the New one they sent me- and all distance issues- healed. The old Remote (altho it lit up was Shot! thanks and shout out to See World Satellites in Indiana Pa.!!!
@@JLPicard440
Yes I was going to suggest that after I asked about the batteries! Sorry I didn't see your comment yesterday or I would have answered sooner. Glad you got it going again.. 😀
I'm surprised it worked with a version 6.4
Me too! Thank you.
I only came here to program my replacement Dish remote and so happy to also use my Apple TV with my Dish remote too. Always losing that little Apple remote! Thanks for great video.
That is awesome!
Is it possible to have 2 of these same remote controls set up as secondary remote access?
If you mean to the Dish receiver, I'd say probably yes, but I've never tried that.
Man I thought that battery thing was the dumbest thing I’ve heard but sure enough I switched em out and it programmed fine 😂😂 thanks!
Lol... yea these things get finicky with weak batteries..
@@JLPicard440 Learn something new every day! Thanks again!
Thanks @Take A Bath Productions, my Sharper Image Sound Bar remote programmed perfectly to my Dish remote! Learning Mode was a great tip you have in this video! Thanks again! :-)
Kyle Coffey Excellent! Thanks 😀😀
Thx for the video Tommy. My first concert was Motley Crue!
Lol..... I wish I had his wallet... 😂
@@JLPicard440 haha. Same!
Thank you!! None of the articles online worked but your video did!
That's awesome! Thanks for the feedback...😊
THANK YOU! Fantastic straight forward and JUST WHAT I WAS SEARCHING FOR! Thanks again
You're welcome.. 😊
Um if I only have the dish remote can I still connect it to my tv and if so what is the code for a sanyo tv
Yes u can... I don't have the codes but they're easy to look up.. you can google remote codes for dish remote and it should come up.. I might have left a Link in the description as well..
@@JLPicard440 thank you
@@leonproctor1843 Youre welcome..
OMG! Thanks! Easy to program with this tutorial! You are awesome!!!! 👍🏽👍🏽👍🏽
Excellent! Thanks for the great comment... 🤩
Thanks I just needed new batteries to program it .works great
Excellent!... Yea batteries can cause trouble when they appear to be fine... :-)
I was able to change the number 2 to 21 on the system setup. I have an insignia roku tv and teying to pair with a dish remote. I don't have a hopper. Everything seems to have worked EXCEPT I cant get the dish remote to turn back on and have dish to come on. When I power off and then back on the roku home page comes in. How do I change this?
It sounds like you have to setup a macro command which is a series of commands that will execute multiple functions with one button press. I can't remember if this remote can do that or not..
Reprogramming a radio receiver
Ok thanks...
I go my BOSE sound bar programed into my DISH remote but have to switch ti AUX everytime I want to vol up or down! Can you help me keep it in SAT mode ti do it all?
I hope this helps. Here's an excerpt from an older Dish Manual:
When the remote control is set up to operate your TV, the MUTE and VOLUME buttons adjust your TV volume when in SAT mode. To use the remote to adjust the volume of a remote-controllable audio receiver or amplifier instead of adjusting the TV’s volume setting, use the steps on this page.
* Press and hold AUX until all Mode buttons are lit, then release it. The AUX mode button flashes.
* Press POUND (#).
* Press the plus (+) side of the VOLUME button.
* Press the 0 number button.
* Press POUND (#). The AUX mode button flashes three times.
Make sure the remote adjusts the amplifiers volume in other modes:
* Press SAT.
* Press the plus (+) and minus (-) sides of the VOLUME button.
* Your tuner/amplifier’s volume changes, and the AUX mode button lights.
Oh Snap my remote has learning! Solved my issues with a new element tv that wouldn't take codes and soundbar that would shut down and Id have to use a separate remote just to turn back on.
Excellent! Thanks for the feedback.. 🙂
How to pair the 54.0 dish remote to Tv without a reciever?
I was looking through the book and I didn't see anything about programming codes. Only pairing to receiver.
Hey thanks. Changing the batteries worked.
You're welcome.. Glad I could help
Thank you!!! You have proven that even a technology idiot can program her replacement remote with your help! God bless you!!!
Lol... nahhh. You're to hard on yourself..😊 You're welcome...
where did you find the codes for devices
Robert Gilbert There’s a link in the description for the codes.... thanks
Thanks this video is very helpful.
You're welcome!... Thanks for watching..
Programming the remote works for volume, mute and on/off. However, it does not work to change the programing from HDMI to TV mode. I have an external antenna for local channels which is the TV mode. Pressing the TV button on the side of the remote does not allow switching from HDMI to TV mode or programming. However, pressing the SAT button on the side of the remote does change from TV programing to HDMI programing. Why shouldn't work for TV programing?
HI. You must have a Hopper with the black dish remote 54.0. That's the only dish remote I know of with the buttons on the side. I do have a hopper video programming the remote to different devices. There's also a input button on the side of the remote. Did you try putting the remote in TV mode and then pushing the input button to see if it'll switch inputs from HDMI to Air/TV?
Thanks for the help it works great
You're welcome...:-)
wonderful. Thanks a lot.
You're welcome... :-)
Volume did not work: Had Sat set up all was good tried Volume with first code on list no go, but then used another code listed on new remote sheet and she works as she is suppose to....Great info thank you 👍👍👍👏👏👏🇨🇦
Excellent! Glad you got it going.. 😁😁
This is late but I changed the address to 2 but then it’s changing on both TVs... what am I doing wrong?
I don't remember exactly. Are there 2 addresses? 1 for the IR main remote and then a 2nd one for the RF remote to the other room? Is the primary remote setup to receive from the RF remote? That could be what's wrong...
WHOOOHOOO.. IT WORKED ON MY NEW REMOTE. THANK YOU SO MUCH.
You're welcome!
Mine just flashes before im finished typing the code
Have you checked the batteries? If they're on the old side, it'll cause trouble like that.
Best tutorial and so easy to understand. 👍👍
Glad it was helpful! Thank you.. 😊
Work great for me change batteries and walla!!! Got it working, Thanks
That's awesome! You're welcome..
When u say that the light should flash green what should I do if the light flashes red
I don't remember exactly.. could be a bad code?
great video- worked perfect thanks
Excellent! You're welcome... :-)
Excellent directions thank you so much!
You're very welcome!
Ok, i'm trying to program my 20.1 IR remote to my tv. i hold the tv button, the lights flash, and then stop. i put in the code, press pound, and nothing happens. is this because of batteries, or something else?
The batteries are the first thing I would check... is it working with other stuff? Make sure you're entering a valid code too...
@@JLPicard440 it works fine for the satellite, the "low battery" notification hasnt come on. and i got the list of codes off of dishes site and went down it. i followed the steps on the website, when i hold the tv button down, the lights all blink 3 or 4 times and then they all turn off, and where it says to input the code and press # and the tv light will blink, the tv light doesnt blink
@@codussigma Just because the Battery low light hasn't come on doesn't mean the batteries are fresh enough to program. It's still worth a try if you have some new ones laying around. There's only 3 choices of what could be wrong.. 1. You're doing something wrong when you program it. 2. The batteries are low 3. There's something wrong with the remote itself. There's no other choice!
Thanks. You were a big help on the remote setup.
You're welcome!
I love the 70s secret agent intro.
LOL.. I don't remember what I did.. 🙂
What would be the codes for an Emerson TV
HI, I usually leave a link to the codes in the description. Thank you.
I'm trying to do my remote and when I hold the tv button all the buttons glow but then they all blink 3 times and it shuts off, what should I do?
Possibly change the batteries? If they're not fresh, give it a try and see if it helps.
What channel does the tv need to be set on to watch dish?
Usually you can change the channels for the secondary TV in the menu of the dish box. I think mine was set to 73. But if your TV is in the same location as the box, it's probably connected via HDMI cable to which ever input it's connected to. HDMI 1, 2... etc.
Hello, on the receiver you have VIP 722K which is a dual receiver do you have a video on how to set up the second tv?
HI, set it up how? The remote?
@@JLPicard440 not the remote how to install 2nd tv with 722k reciver on the back there is no wire to hook up to the other tv how is the signal being sent to the other tv?
@@eastovercitgo3295 oic... that's a little more complicated than I can explain in a message. If you Google wiring diagram for dish 722 2nd receiver it should bring up a picture so u can see what to do... hopefully this will help...thanks
Excellent! Easy peasy. Thanks!
You're welcome!
I have a Samsung HDMI Model UN324500MF and I have it connected to a DISH Hopper. I want to be able to use my DISH remote to change source from DISH to HD ANTENNA. We have hurricanes in South Florida and I want to be able to use the remote to go from CAble to Local TV. Also, we are being told our DISH will no longer cover Local TV. How can I program the remote to move from DISH JOEY to ANTENNA.
There's a input button on the remote... it won't switch inputs when you select the TV mode? It should..
THANKS SO MUCH !!!
You're welcome..
I have a dish remote 21.1 IR/UHF Pro remote. It was programmed to turn off my Samsung TV and now it has stopped working and i have re-programmed by entering the remote code and it still will not work. I’ve tried your learned method on the remote without any success. Any suggestions?
Do i need a new remote? I’ve tried to call Dish and they were no help. They kept saying that my TV is not compatible with the remote. Which is ridiculous cuz it was working previously.
How can they say Samsung is not compatible...That's a major brand name... what a joke!.. I have a Samsung and it works great. Sorry for the troubles.. did you check the batteries to make sure they're pretty fresh? If you have a different TV, try it on that to see if it works ok. Do you have the original Samsung remote to make sure something didn't happen to the TV itself.. long shot, but you never know...
Any tips for Sanyo sound bar?
It should program in the same way as the TV or DVD, I think it goes on the aux device button.... if that doesn't work, I believe the remote is teachable.. if you have the original remote you can teach the commands for the sound bar.
Rudy! Rudy! Rudy! Rudy! Thanx for Vid and links.
You're welcome!... 😀
I’m trying to reprogram a 20.1 ir remote to control 2 TVs in one house and then reprogram the UHF to a new tv ina different location. ?? Can u send. A link how to do this.
The second remote right now is programmed to a tv I use to have next door but I need it to be reprogrammed to a new tv next door.
I think you might be able to put the 2nd TV on the Aux button on the remote. The uhf works on an address that's in the satellite receiver. I don't really have a link you can go to except Dish Network themselves has some info on programming their remotes..This link should get you started.. :
my.dish.com/support/products/remotes/how-to/program-to-tvother
Hi I have a sharp tv and a 21.1 ir/uhf pro and I tried every single code on the list on dish website but nothing works. Is there any other way to get it work?
Yes, if you have your original remote, you can teach the dish remote the things you need. Not sure why nothing works. Sharp is a mainstream brand.. It should definitely work with Sharp.
@@JLPicard440 thanks for the response, I contacted customer support and they tried everything they can and said I got a defective remote, so they going to send me another one.
@@wangu4951 Yes that's a good possibility! Thanks for the update.. 😀
Thank you Soooo much. It really helped 😃
You're welcome!
Thank you so much!!! I needed this.
You are so welcome!
Thanks!
You're welcome... :-)
Excellent video 😎👍🏻
Thanks.... :-)
My remote is a 21.0 is it any different than the 21.1
I'm pretty sure they're both about the same...
You’re the best
You are! Thank you... 🙂
THANK YOU SO MUCH!! You were a great help!!!
You're welcome!
I have remote #2 on my second tv, everything works except for the Volume and Power Button. I’ve tried everything and can’t get them to work. When I try to program the tv and, hold and press tv button , i get the “ Attention - Mode Reminder” every time. CAN YOU PLEASE HELP ME
Hmmmm. maybe try turning off the satellite receiver, it doesn't need to be on for this. Also, try replacing the batteries if they're not that fresh..
I have the same problem did you find the solution
Thank you so much! That was so easy!
You're welcome!
How do I get a code for a westinghouse 32"dtv
There should be a link in the description for the codes, if not it's easy to google codes for dish network remote.. That should bring up the list.
Well done!
Thank U!.. :-)
How do I go from watching a DVD back to the satellite
switch the devices at the top back to sat on the left
Thankyou very much!
You're welcome!
Thank you!! U totally helped me out.
Glad I could help! You're welcome..
Thanks, this video was very helpful!
Glad to hear it!
Thank you very informative
Glad it was helpful! You're welcome..
Everytime i press tv the sat button lights up then the tv button flashes when I let go
Ive never seen that happen. How are the batteries, when they are low it can cause weird problems.
Ty I had the same tv as you so it was so essay
Awesome! 🤓😎😃
Thanks a lot, it is very helpful. The remote is programmed with TV, however it won't pair/work with dish receiver. Can you help?
It could be the remote address. Make sure the remote address is set to the same as the receiver. Try this... ;
www.mydish.com/support/products/remotes/how-to/program-to-receiver
It could also be that it is set for remote 2 . If it is a 21.1 , open the battery compartment and find a small toggle . Switch it from UHF to IR . Then the end cap can be pulled and flipped over. One side says 2 and the other says 1 Hope this helps. Thank you Take a Bath Productions for this helpful video.