Hello dear sir. Congratulations, your work is fantastic, I learn a lot from your videos. I would like to ask if you have videos on installing an alarm on a Kugoo Kirin M4 Pro scooter. The controller does not have any connector with an alarm function. I use a TF-100 display with a round pin connector. If you can respond I would be grateful. Greetings from Portugal, thank you
the brake cable (black and white one) will work withouy the cable for the light (black, white and orange)? can the ebrake be used only with the black and white cable connected? Thanks for your time.
the brake cable (black and white one) will work withouy the cable for the light (black, white and orange)? -- yes, they are independent can the ebrake be used only with the black and white cable connected? -- yes, should be no problem at all
Dear friend, I'm Orlando Tristão and I'm from Portugal. Your video is simple but very good. I regret not being able to take advantage of it as I cannot speak English and the subtitles are not good, but I got the point. I would like to connect two controllers of a Dualtron Thunder 2 and the Display, do you happen to have a video or an explanation that could help me? I will be grateful. I wish you much success in your work. A hug. Thanks
bossing musta tatanong lng ung trottinette ko nag palit ako ng stator ngayon kapag power on ko then start aandar sia 3to5?second lng tas ayaw na power off then start ganun parin
Bossing gud eve Tanong po Sana kami KC ung ebike 2 wheels Namin Meron po xang power kaso Hindi mg-ikot o mag-andar Ang motor. Ano po kadalasan sira Neto?
Hello my friend. I have a JP 52V 25a dual motor controller. In controller A I have 2 separate gray wires and in controller B there are also 2 separate gray wires. They are the same as in your video. Are these cables for self-study?
Sir my ask lng po ako.. Meron akong controller home energy ung name 60v/72v 90a. I tried to connect to my motor which is 60/72v 3000w with hall sensor.. Ngpalit din ako ng throttle s original display nya. Correct nmn ung kabit kc tumatakbo ung motor. Pero my error 10 at hnd n reread ang speed nya. Ano po nakikita nyong prob? Bago po lahat pti motor.
Sir anong kulay ng wire ung nilagyan mo ng connector pra s dual hub.. naayos q kc ung scooter q ngaun ung nbili q n controller nkatengga n.. binabalak q n idual hub nlang..
sir ask ko lang po ung issue ng scooter q,,tinister q po ung voltage ng battery, ok naman pero pag siniwitch on q po lumalabas lng saglit ung voltage reading sa voltmeter tas nagda drop to zero na sya,,
Sana ganyan yung dumating order ko sa lazada sa unitra happy ano advice mo sir ikakabit ko ba yung volt meter ko sa main battery directly or jan na sa motor controler na pag nag on lalabas din yung same Voltage nang battery
wiring sir, check maigi. as practice, ilagay nyo muna is battery, controller, throttle. then ON unit, para malimit natin at mafilter ano talaga ang sira.
Orange and black wire is voltage output,but where does it go?there isn't a plug for me to plug into,I can't get the display to turn on,it was working and I plugged out some wires and forgot where they went,but got them all in order,from copying videos,but I just need the display to turn on,been on this week's now,someone please help,
2 года назад
hello , mr100 has accelerator pedal, p12 mode is not active. how can i activate it. first start is too slow
@@robertianbelo7201 39V is cutoff V ng controller nio. 48V lang yang controller nio. Hindi yang capable of voltage range like other controllers na medyo mamahalin.
HI SIR ASK KO LANG PO SA DUAL HUB MTOR 60V EACH 1600W X2=3200WATTS W/ CONTROLLER Z66018SHZZ MODEL 60V/ 2PCS,BATTS CAPACITY 60V-24AH /INPUT:67.2V 10A. TANONG KO LANG PO IF PAANO SYA E UPGRADE OR Palakasin pa yung takbo nang escooter? begginer po kasi ako here in taiwan pra sa work.sana po matulungan nyo po ako.
ilang watts/amps yan controller ninyo na Z66018SHZZ? kung 30A yan, hanap ka pa ng mas mataas na amps. sa hub naman, ilang RPM? hanap ka pa ng mas mataas na RPM.
Boss nasira ung throttle ko nawalan ng display mula nong ginamit ko ung usb ng throttle para gawing usb flashlight or ilaw tpos bumili ako ng bagong throttle ayaw nman mag on
yan nga advise ko sa mga videos ko, wag gamitin yung USB ng mga throttle may chance na nadamay controller mo or baka hindi compatible yung binili mong bago, same brand ba?
Need open throttle, check kung may voltage na napasok sa Red and Black, if wala, meaning walang binabato si controller. If meron, tas hindi ma ON ang throttle, may prob sa throttle.
@@mskgenmer Meron naman pong power supply 54v. Pag idiniin ko ang power button tas hindi bibitawan gumagana naman mga lights nya pati horn. Ayaw lang talaga mag power on ang throttle nya. May available po ba kayong J&P throttle?
Boss sana mapansin mo comment ko..pa help po sana Ako Kase Yung scooter ko pinalitan ko po ng controller..Ang nging problem po pag palit ko Yung ikot ng gulong baliktad na po tas nwala Yung takbo nya sa screen at Ang bagal po
@@mskgenmer Do you have or can you get the wire diagram for the fieabor Q06+? I have reached out to the fieabor and they will not help. I had a kid unplug the connectors and now can't figure out which connectors go where. Any help would be greatly appreciated! Thanks
@@mskgenmer boss controller related question po. ano po ba ibig sabihin pag nagbi-blink yung controller icon sa display pero ummandar naman yung scooter?
Ito ang content creator na ayos panoorin. Maayos magpaliwanag, at hindi kupal. Smooth lang. Thank you sir! :)
Salamat idol sa review ng wiring nakuha kona yong sa break ligth conection
welcome sir, salamat po
You are the best
Hello dear sir. Congratulations, your work is fantastic, I learn a lot from your videos. I would like to ask if you have videos on installing an alarm on a Kugoo Kirin M4 Pro scooter. The controller does not have any connector with an alarm function. I use a TF-100 display with a round pin connector. If you can respond I would be grateful. Greetings from Portugal, thank you
Salamat sa pag bahage mo idol.. May nalalaman ako dito
thanks bossing :)
the brake cable (black and white one) will work withouy the cable for the light (black, white and orange)? can the ebrake be used only with the black and white cable connected? Thanks for your time.
the brake cable (black and white one) will work withouy the cable for the light (black, white and orange)? -- yes, they are independent
can the ebrake be used only with the black and white cable connected? -- yes, should be no problem at all
Meron akong controller n ganyan (jp). Pwede po b yan sa ordinary throtle like generic n d pihit or pang xiaomi m365
Dear friend, I'm Orlando Tristão and I'm from Portugal. Your video is simple but very good. I regret not being able to take advantage of it as I cannot speak English and the subtitles are not good, but I got the point. I would like to connect two controllers of a Dualtron Thunder 2 and the Display, do you happen to have a video or an explanation that could help me? I will be grateful. I wish you much success in your work. A hug. Thanks
on my way making it, thank you
bossing musta tatanong lng ung trottinette ko nag palit ako ng stator ngayon kapag power on ko then start aandar sia 3to5?second lng tas ayaw na power off then start ganun parin
THANK YOU FOR YOUR VIDEO EXCELLENT INFORMATION 🇺🇸❤🛴
Our pleasure!
Bossing gud eve Tanong po Sana kami KC ung ebike 2 wheels Namin Meron po xang power kaso Hindi mg-ikot o mag-andar Ang motor. Ano po kadalasan sira Neto?
Marami pong reason. Controller. Throttle. Wiring. Etc..
Hi there i have a kugoo g2 pro but want to upgrade to the 48v 25a no hall sensor controller and lcd but do i need to change data cable from g2 pro ?
if your current throttle-controller data cable is 6 core, you may re-use it, otherwise, get new one
Sir ano po mangyayari kung magtataas k ng amps? Palitan q sana kc from 25a to 50a ung controller ano po magiging problema?
Sir asked kolang if pwd 5pin hub motor sa 6pin controler?
Just checked on JP 48v 25A controller. Its not a self learning direction spin wire BUT a SPEED LIMIT WIRE.
Sso if i unplug will it go faster?
@@AliensUnderOathyes, of corse.
@@AliensUnderOath how fast did you make it go?
Hello my friend. I have a JP 52V 25a dual motor controller. In controller A I have 2 separate gray wires and in controller B there are also 2 separate gray wires. They are the same as in your video. Are these cables for self-study?
They are speed limiters
Cioa ho una domanda.i due cavetti grigi dove vanno attaccati?e cosa sono bisogna coleggarli per forza?
English please
How much voltage can you measure on the starting wire (orange) to turn on/off the controller?
👍👍👍👍👍👍👍
Sir my ask lng po ako.. Meron akong controller home energy ung name 60v/72v 90a. I tried to connect to my motor which is 60/72v 3000w with hall sensor.. Ngpalit din ako ng throttle s original display nya. Correct nmn ung kabit kc tumatakbo ung motor. Pero my error 10 at hnd n reread ang speed nya. Ano po nakikita nyong prob? Bago po lahat pti motor.
error 10, hmmm.. di ko pa naexperience boss
@@mskgenmer ok boss slamat.
Paps, yang controller n yan. Ilan max speed kya at pde kaya sa 48volt 30ah??
60-70kph
Bro sana makagawa ka video about M5 grandoise or M5 lng controller how to by pass electronic ignition to manual key ignition. Many thanks in advance!
Sa key ignition, pagdikitin lang red and gray/green.
pede ba yan gamitin sa brushed motor like 775 ?
775 po?
@@mskgenmer yes brush motor 775
Do all the different throttles styles work with jp controller as long as pins are correct?
in my experience, no.
Sir anong kulay ng wire ung nilagyan mo ng connector pra s dual hub.. naayos q kc ung scooter q ngaun ung nbili q n controller nkatengga n.. binabalak q n idual hub nlang..
may video ako dual hub sir, yun watch mo
sir ask ko lang po ung issue ng scooter q,,tinister q po ung voltage ng battery, ok naman pero pag siniwitch on q po lumalabas lng saglit ung voltage reading sa voltmeter tas nagda drop to zero na sya,,
BMS or weak cell ng battery.
sir ask ko lang, possible ba na ang masira ay battery controller? kpg ng spark ung wire? oh sa throtle?
normal na may spark pag ikakabit ang battery sa controller, unless gagamit ka ng connector na anti spark
pwede po ba jp lang na controle? j&p kc ung luma ko sa t113 unit
Pwede po
My problema po ung display ko full nman battery nya pero empty nkalagay sa display. Bago na controller at battery ko pero ganun pdin.. bkt po kaya
mali P settings, kindly see video po ng P-settings
HH-100 po throttle ko wala po syang odometer ano po lang throttle ang pwede ko ipalit sa kanya ?
dapat ganyan din, kapag iba kasi hindi magcocomunicate sa controller. or change controller and throttle 1 time
Sana ganyan yung dumating order ko sa lazada sa unitra happy ano advice mo sir ikakabit ko ba yung volt meter ko sa main battery directly or jan na sa motor controler na pag nag on lalabas din yung same Voltage nang battery
Sa isip ko sa main battery directly nalang siguro kasi may settings yun baka ma bura pag nag off na si controller ang name nang volt meter is supnova
Kung gusto mo actual talaga ng battery charge, edi sa battery. Pag sa controller, may konting losses.
Ahh ok ok kunti lang cguro kain nyan gagawa kasi ako nang Scooter controller and frame nalang kulang papa welding kupa
@@mskgenmer sir same lng ba ya Ng njax t ung scooter ko kc nawala ung break indicator saka ung speed meter nya pero gumagana nman scooter ko
I wanted to ask how can I test the controller without the Display? Is it possible to connect an accelerator instead of the Display? Thanks
Ngpalit n po kc aq controller bago kaso lng same padin ung blinking controller padin.. ano po kya sira nun..
wiring sir, check maigi. as practice, ilagay nyo muna is battery, controller, throttle. then ON unit, para malimit natin at mafilter ano talaga ang sira.
What is the orange wire for and where to conect
sir pwede ba ikabit ang jp controller sa hub na may hall censor?
May video ako sir latest. Sensorless vs sensortype. Pakicheck po.
Orange and black wire on the Jap controller I have any idea
Voltage output
Orange and black wire is voltage output,but where does it go?there isn't a plug for me to plug into,I can't get the display to turn on,it was working and I plugged out some wires and forgot where they went,but got them all in order,from copying videos,but I just need the display to turn on,been on this week's now,someone please help,
hello ,
mr100 has accelerator pedal, p12 mode is not active.
how can i activate it.
first start is too slow
Some MR-100 don't have it actually.
Sir anong watt po yan... Tanong ko lang rin po pwd ba gamitan nang 800watt controller un 700watt motor 52v
1500watts po, okay lang yan sir, may tolerance naman motor, kaya pa yan
Boss tanong ko lang po yong kugoo g booster ko po kasi 48V pwde ko po ba siya gawin kahit 60V? Salamat. 20ah battery niya stock
Check mo controller mo kung 48-60 range. Kung hinde, change controller, battery and hub motor.
@@mskgenmer cheneck ko boss controller ko 39V lang nakalagay saka 25A
@@robertianbelo7201 39V is cutoff V ng controller nio. 48V lang yang controller nio. Hindi yang capable of voltage range like other controllers na medyo mamahalin.
HI SIR ASK KO LANG PO SA DUAL HUB MTOR 60V EACH 1600W X2=3200WATTS W/ CONTROLLER Z66018SHZZ MODEL 60V/ 2PCS,BATTS CAPACITY 60V-24AH /INPUT:67.2V 10A.
TANONG KO LANG PO IF PAANO SYA E UPGRADE OR Palakasin pa yung takbo nang escooter? begginer po kasi ako here in taiwan pra sa work.sana po matulungan nyo po ako.
ilang watts/amps yan controller ninyo na Z66018SHZZ? kung 30A yan, hanap ka pa ng mas mataas na amps. sa hub naman, ilang RPM? hanap ka pa ng mas mataas na RPM.
Boss pa turo naman ng dual hub anong color yung i tap??
May video ako gagawin sir about dual hub. Pa wait nalang po
Sir saan pwede i-tap ang 12v para sa reverse horn?. TIA.
walang 12V output sa controller, gamit ka stepdown
New sub sir.ano po masugest nyo tester baguhan po
Fluke. 😊
Yown boss pede kaya to sa fieabor qx5 plus?
Ibig nyong sabihin kung pwede yung wiring diagram na yan? Check nio po kung yung J&P niyo is sensorless or sensor type.
Bos magkano yung JP controler 52 volts 23 ah sa inyo
Please message us in page po
Boss nasira ung throttle ko nawalan ng display mula nong ginamit ko ung usb ng throttle para gawing usb flashlight or ilaw tpos bumili ako ng bagong throttle ayaw nman mag on
yan nga advise ko sa mga videos ko, wag gamitin yung USB ng mga throttle
may chance na nadamay controller mo or baka hindi compatible yung binili mong bago, same brand ba?
Hello and for dual motor?
I have video for dual motor
For contrôler a/b jp?
Paano naman po sir kapag ang throttle ay hindi nagpower-on? Ano po possible na nasira? Thanks in advance sa sagot.
Need open throttle, check kung may voltage na napasok sa Red and Black, if wala, meaning walang binabato si controller. If meron, tas hindi ma ON ang throttle, may prob sa throttle.
@@mskgenmer Meron naman pong power supply 54v. Pag idiniin ko ang power button tas hindi bibitawan gumagana naman mga lights nya pati horn. Ayaw lang talaga mag power on ang throttle nya. May available po ba kayong J&P throttle?
Available pa pi ba ito sa shop nyo sir
Wala pa po kami JAP controller sa ngayon. Sorry.
Eto pa lang po ang meron.
SHOPEE: invol.co/cl56h03
LAZADA: invol.co/cl730bk
How to use self learning cable and reverse the motor hub?
I have video showing it. Please search.
@@mskgenmer then the video doesnt have the right tittle. I cant find.
My controller is restricted to run at 20km/h, how I can modify controller to run at full potential? Please help
That's normal for low end controllers. What brand is your controller?
Ma vanno tenuti scollegati i cavi di autoapprendimento?
Yes that should always be disconnected
Boss sana mapansin mo comment ko..pa help po sana Ako Kase Yung scooter ko pinalitan ko po ng controller..Ang nging problem po pag palit ko Yung ikot ng gulong baliktad na po tas nwala Yung takbo nya sa screen at Ang bagal po
pag baliktad, check video ko rito sir, meron ako video dito sa YT
May no. Ka sir
Sir san pwede magkabit ng thumb throttle?
Sa amin? :)
Please upload dc controller wirimg diagram..🙏
coming soon
Ano po top speed na JnP?
90kph no load
Sir san po location niyo?
san pedro laguna, message nio na lang po kami sa FB namin :)
Sir hanggang ilang watts ng hub ang kaya ng ng jp controller n 60v 25a?
Jp controller din sya 48v 25a
Ibig nyong sabihin kung pwede yung wiring diagram na yan? Check nio po kung yung J&P niyo is sensorless or sensor type.
@@mskgenmer Do you have or can you get the wire diagram for the fieabor Q06+? I have reached out to the fieabor and they will not help. I had a kid unplug the connectors and now can't figure out which connectors go where. Any help would be greatly appreciated! Thanks
Where could i get full JP wire diagram
single hub or dual? actually internet has a lot. or message us in FB
Singolo
Anche io cerco lo schema jp singolo 48v 25ah hall
boss saan po yung sensor ng speedometer? biglang di kasi gumagana yung saakin.
Check mo hub hall sensor, or sa loob mismo na ng controller sira
@@mskgenmer boss controller related question po. ano po ba ibig sabihin pag nagbi-blink yung controller icon sa display pero ummandar naman yung scooter?
@@gigababies2922 Not sure, hindi pa po na experience. Research natin yan :)
Why is the title in English if the audio isn’t…
Why can't I use this controller for my ebike?
Pas sensor dosent have
My e bike is 350 w. 48 volts pls help me
Big wire
Orange big wire where to conect
Hey I am interested to make dual motor. Could you please show how to connect two controllers?
I have video here. Please search.
saan po nakakabili ng controler
facebook.com/mskgenmer
hey, where is wiring diagram?
Send me a message in Page.
@@mskgenmer hello could you please send me the wiring diagram for dual motor ?
Hi have error 5 pls help
E-05 is battery low. What model of throttle are you using?
Hello friend.Which outputs on the circuit board are connected to the cables that provide voltage when the brake sensor is activated?
share a pic please!!😢
in 11:23 :)